Laney FS4 Four Switch Pedal User Manual
- June 12, 2024
- Laney
Table of Contents
Laney FS4 Four Switch Pedal
Product Information
The FS4 is a footswitch designed to control amps that require up to four
features to be switched. It comes with 4 footswitches and a sticker sheet for
labeling. The FS4 is suitable for controlling the LANEY IRONHEART range of
amps, specifically the LEAD, CLEAN, REVERB, and BOOST functions.
Features
- 4 footswitches
- Blank switches that can be labeled using the provided sticker sheet
- LED indicators for active functions
- 5 pin DIN socket for connection to the IRT amplifier
- Cannot be used simultaneously with remote jack sockets on the amp
Top View
The FS4 does not have any labeling on the switches when it arrives. The
sticker sheet is used to correctly label each switch for the amp it’s
controlling.
Rear View
The rear panel of the FS4 has a 5 pin DIN socket for connecting to the IRT
amplifier using the provided DIN cable. Note that when using the FS4 to
control your amp, any remote jack sockets (if present) cannot be used
simultaneously.
Labeling
The FS4 is specifically designed for controlling the LANEY IRONHEART range
of amps. The switches should be labeled as follows from left to right: LEAD,
CLEAN, REVERB, and BOOST. When the associated function is active, the adjacent
LED will light up. If the FS4 is not being used with one of the listed
amplifiers, it is recommended to check each footswitch with the assumed
function before labeling.
Safety and Warnings
It is important to carefully read the owner’s manual for proper usage and
to ensure the long and trouble-free performance of the product. When unpacking
the product, check for any signs of damage that may have occurred during
transit. When connecting the FS4, ensure that the wire colored green and
yellow is connected to the terminal marked by the letter E, the earth symbol,
colored green or colored green and yellow.The product manual contains
important operating and maintenance instructions that should be followed.
INTRODUCTION
FEATURES
- Solid metal chassis construction
- 4 high-quality switching components
- Active control status LEDs
- Sticker sheet included
- 3M long 5 pin DIN cable
TOP VIEW
The FS4 comes with 4 footswitches designed to control amps that require up to four features to be switched. When it arrives, your FS4 will be blank with no labeling on each of the switches. A sticker sheet is provided with your product to correctly label the FS4 for the amp it’s controlling.
REARVIEW
On the rear
panel of your FS4, you’ll find the 5-pin DIN socket to be used with the
provided DIN cable.
Plug in here and connect the other end to your IRT amplifier.
NOTE: when using the FS4 to control your amp, any remote jack sockets (if
present) cannot be used simultaneously.
LABELLING
Ironheart Range
Your FS4 is suitable for controlling the LANEY IRONHEART range of amps with four main functions: LEAD, CLEAN, REVERB, and BOOST from left to right. Use your sticker sheet to label the switches as shown. When the associated function is active, the adjacent LED will light up
Other
If your FS4 is not being used with one of the amplifiers listed, we recommend
checking each footswitch with the assumed function before labeling. The image
below shows the full sticker sheet included with the FS4:
SAFETY AND WARNINGS
In order to take full advantage of your new product and enjoy long and trouble-free performance, please read this owner’s manual carefully, and keep it in a safe place for future reference.
- Unpacking: On unpacking your product please check carefully for any signs of damage that may have occurred whilst in transit from the Laney factory to your dealer. In the unlikely event that there has been damage, please re-pack your unit in its original carton and consult your dealer. We strongly advise you to keep your original transit carton, since in the unlikely event that your unit should develop a fault, you will be able to return it to you dealer for rectification securely packed.
- Amplifier Connection: In order to avoid damage, Generally it is advisable to establish and follow a pattern for turning on and off your system. With all system parts connected, turn on source equipment, mixers, effects processors etc, BEFORE turning on your amplifier. Many products have large transient surges at turn on and off which can cause damage to your speakers. By turning on your amplifier LAST and make sure its level control is set to a minimum, any transients from other equipment should not reach your loudspeakers. Wait till all system parts have stabilized, usually a couple of seconds. Similarly when turning off your system always turn down the level controls on your amplifier and then turn off its power before turning off other equipment.
- Cables: Never use shielded or microphone cables for any speaker connections as this will not be substantial enough to handle the amplifier load and could cause damage to your complete system. Use good quality shielded cables everywhere else.
- Servicing: The user should not attempt to service these products. Refer all servicing to qualified service personnel.
- Heed all warnings.
- Follow all instructions.
- Do not use this apparatus near water.
- Clean only with a dry cloth.
- do not block any of the ventilation openings. Install in accordance with manufacturer’s instructions.
- Do not install near any heat sources such as radiators, heat registers, stoves or other apparatus (including amplifiers) that produce heat.
- An apparatus with Class I construction shall be connected to a main socket outlet with a protective connection. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding-type plug has two blades and a third grounding prong. The wide blade or third prong is provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for the replacement of the obsolete outlet.
- Protect the power cord from being walked on or pinched, particularly at plugs, convenience receptacles, and the point they exit from the apparatus.
- Only use attachments/accessories provided by the manufacturer.
- Use only with a cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.
- The mains plug or an appliance coupler is used as the disconnect device and shall remain readily operable. The user should allow easy access to any mains plug, mains coupler and mains switch used in conjunction with this unit thus making it readily operable. Unplug this apparatus during lightning storms or when unused for long periods of time.
- Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as when the power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.
- Never break off the ground pin. Connect only to a power supply of the type marked on the unit adjacent to the power supply cord.
- If this product is to be mounted in an equipment rack, rear support should be provided.
- Note for UK only: If the colors of the wires in the mains lead of this unit do not correspond with the terminals in your plug‚ proceed as follows: The wire that is colored green and yellow must be connected to the terminal that is marked by the letter E‚ the earth symbol‚ colored green or colored green and yellow. The wire that is colored blue must be connected to the terminal that is marked with the letter N or the color black. The wire that is colored brown must be connected to the terminal that is marked with the letter L or the color red.
- This electrical apparatus should not be exposed to dripping or splashing and care should be taken not to place objects containing liquids, such as vases, upon the apparatus.
- Exposure to extremely high noise levels may cause permanent hearing loss. Individuals vary considerably in susceptibility to noise-induced hearing loss, but nearly everyone will lose some hearing if exposed to sufficiently intense noise for a sufficient time. The U.S. Government’s Occupational Safety and Health Administration (OSHA) has specified the following permissible noise level exposures: According to OSHA, any exposure in excess of the above permissible limits could result in some hearing loss. Earplugs or protectors to the ear canals or over the ears must be worn when operating this amplification system in order to prevent permanent hearing loss if exposure is in excess of the limits as set forth above. To ensure potentially dangerous exposure to high sound pressure levels, it is recommended that all persons exposed to equipment capable of producing high sound pressure levels such as this amplification system be protected by hearing protectors while this unit is in operation.
- If your appliance features a tilting mechanism or a kickback-style cabinet, please use this design feature with caution. Due to the ease with which the amplifier can be moved between straight and tilted back positions, only use the amplifier on a level, stable surface. DO NOT operate the amplifier on a desk, table, shelf or otherwise unsuitable non-stable platform.
- Symbols & nomenclature used on the product and in the product manuals, intended to alert the operator to areas where extra caution may be necessary, are as follows: Intended to alert the user to the presence of uninsulated ‘Dangerous Voltage’ within the product’s enclosure that may be sufficient to constitute a risk of electrical shock to persons. Intended to alert the user of the presence of important operating and maintenance (Servicing) instructions in the literature accompanying the product.
CAUTION: Risk of electrical shock – DO NOT OPEN. To reduce the risk of electrical shock, do not remove the cover. No user-serviceable parts inside. Refer servicing to qualified personnel.
WARNING: To prevent electrical shock or fire hazards, do not expose this appliance to rain or moisture. Before using this appliance please read the operating instructions for further warnings.
This device complies with Part 15 of the FCC rules Operation is subject to the following two conditions:
- This device may not cause harmful interference
- This device must accept any interference received, that may cause undesired operation.
Warning: Changes or modifications to the equipment not approved by Laney can void the user’s authority to use the equipment.
Note: This equipment has been tested and found to comply with the limits for Class B digital devices, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try and correct the interference by one or more of the following measures. Reorient or relocate the receiving antenna. Increase the separation between the equipment and the receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. This product conforms to the requirements of the following European Regulations, Directives & Rules: CE Mark (93/68/EEC), Low Voltage (2014/35/EU), EMC (2014/30/EU), RoHS (2011/65/EU), ErP (2009/125/EU)
SIMPLIFIED EU DECLARATION OF CONFORMITY
Hereby, Laney Electronics Ltd. declares that the radio equipment is in
compliance with Directives 2014/53/EU, 2011/65/EU, and 2009/125/EU. Full text
of the EU declaration of conformity is available at the following internet
address:
http://support.laney.co.uk/approvals
The object of the declaration described above is in conformity with the relevant statutory requirements of Electrical Equipment (Safety) Regulations 2016, Electromagnetic Compatibility Regulations 2016, The Restriction of the use of Certain Hazardous Substances in Electrical and Electronic Equipment Regulations 2012, The Ecodesign for Energy-Related Products and Energy Information, (Amendment) (EU Exit) Regulations 2012 In order to reduce environmental damage, at the end of its useful life, this product must not be disposed of along with normal household waste to landfill sites. It must be taken to an approved recycling centre according to the recommendations of the WEEE (Waste Electrical and Electronic Equipment) directive applicable in your country STEELPARK ROAD, COOMBSWOOD BUSINESS PARK WEST, HALESOWEN, B62 8HD. UK FOR THE LATEST INFORMATION PLEASE VISIT WWW.LANEY.CO.UK IN THE INTEREST OF CONTINUED DEVELOPMENT, LANEY RESERVES THE RIGHT TO AMEND PRODUCT SPECIFICATIONS WITHOUT PRIOR NOTIFICATION.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>