Kinetic technologies KTD2690 Single Flash LED Driver User Manual
- June 12, 2024
- Kinetic Technologies
Table of Contents
- Kinetic technologies KTD2690 Single Flash LED Driver
- Product Information
- Product Usage Instructions
- Brief Description
- Ordering Information
- 3D CAD Image
- User-Supplied Equipment
- Jumper Descriptions
- Quick-Start Procedures
- Graphical User Interface
- Electrical Schematic
- Printed Circuit Board (PCB)
- Additional Test Procedures
- Troubleshooting
- Important Notices
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
Kinetic technologies KTD2690 Single Flash LED Driver
Product Information
Product Name | KTD2690 EVAL Kit |
---|---|
Part Number | KTD2690EVAB-MMEV01 |
IC Package | UDFN22-10 |
Description | KTD2690 is a single flash LED driver with a programmable 1.5A |
current source. The EVAL Kit is used to demonstrate and evaluate
the functionality, performance, and PCB layout of the KTD2690 in
UDFN package.
Product Usage Instructions
- Ensure that the following user-supplied equipment is available:
- – VIN, VOUT, LED LX power supply with a voltage range of 2.7V to 5.5V
- Optional equipment:
- – Graphical User Interface (GUI) software
- Recommended operating conditions:
- – VIN, VOUT, LED LX voltage: 2.7V to 5.5V
- Jumper Descriptions:
Designator | Name | Description | Default |
---|---|---|---|
P1 | VIN_I2C | Jumper to connect the LED (D1). To use the on-board LED (D1), |
the jumper is present. To use an external LED, the jumper is
removed.| Open
P3| STROBE| Jumper to short the 0.1 sense resistor (R3). When the jumper is
not present, measuring the voltage across P5 testpoints allows
calculating the LED current ILED = VP5 / 0.1.| LED open
Follow the Quick-Start Procedures in the user manual for more detailed instructions on using the EVAL Kit and the Graphical User Interface (GUI) software.
Graphical User Interface (GUI) Window
To Check the I2C Connection to the Device:
- Open the GUI software.
- Follow the instructions in the user manual for checking the I2C connection to the KTD2690 device.
To Turn on Flash Mode by I2C Command for 1000ms Duration at 375mA Flash Current:
- Open the GUI software.
- Follow the instructions in the user manual for turning on the flash mode using the I2C command.
Note: Refer to the Electrical Schematic and Bill of Materials(BOM) in the user manual for additional technical information about the EVAL Kit.
Brief Description
The KTD2690 Evaluation (EVAL) Kit is used to demonstrate and evaluate the KTD2690 in UDFN package functionality, performance, and PCB layout. The kit includes a fully assembled and tested PCB with the KTD2690 IC installed, and a printed copy of the Quick-Start Guide (also contained within this document).
Ordering Information
Part Number | Description | IC Package |
---|---|---|
KTD2690EVAB-MMEV01 | KTD2690 EVAL Kit | UDFN22-10 |
3D CAD Image
EVAL Kit Physical Contents
Item # | Description | Quantity |
---|---|---|
1 | KTD2690 EVAL Kit fully assembled PCB | 1 |
2 | MCP2221A Board – General Purpose USB to GPIO I2C – Stemma QT / Qwiic | 1 |
3 | Stemma QT / Qwiic JST SH 4-pin Cable – 100mm Long | 1 |
4 | Anti-static bag | 1 |
5 | KTD2690 EVAL Kit Quick-Start Guide — printed 1-page (A4 or US Letter) | 1 |
6 | EVAL Kit box | 1 |
QR Links for Documents
User-Supplied Equipment
Required Equipment
- Bench Power Supply for VIN 5V and 3A, as needed for the intended application.
- Digital Multimeter – one or more, used to measure input/output voltages and currents.
Optional Equipment
- Oscilloscope – for dynamic testing of voltages (and currents with a current probe, if available).
- Additional Digital Multimeters
Recommended Operating Conditions
Symbol | Description | Value | Units |
---|---|---|---|
VIN, VOUT, LED | 2.7 to 5.5 | V | |
LX | ≤ 6 | V |
Jumper Descriptions
Designator | Name | Description | Default |
---|
P1
| ****
VIN_I2C
| I2C logic supply
· Open: VIN_I2C should be supplied externally from the MPC2221A board via the 4-wire Stemma cable
· VIN: with the jumper present, VIN_I2C is supplied from VIN
| ****
open
P3
| ****
STROBE
| Flash STROBE control input
· GND: STROBE input set low to GND (disabled)
· VIN: STROBE input set high to VIN (enabled)
|
P4
| ****
LED
| Jumper to connect the LED (D1).
To use the on-board LED (D1), the jumper is present. To use an external LED, the jumper is removed.
| ****
LED
P5
| ****
GND
| Jumper to short the 0.1Ω sense resistor (R3).
When the jumper is not present, measuring the voltage across P5 testpoints allows to calculate the LED current ILED = VP5 / 0.1.
| ****
open
Quick-Start Procedures
- Connect one pair of Banana-to-clip power cables to the test points at VIN and GND (left side of EVAL Kit).
- Before connecting the EVAL Kit to the VIN bench supply, turn on the supply and adjust the voltage as close to 0V as possible. Then turn off the supply. While off, connect the banana ends of the Banana-to-clip power cables to the VIN bench supply.
- Turn on the VIN bench supply and very slowly ramp its voltage to an appropriate voltage of 3.6V. While ramping VIN slowly, use the bench supply’s output current indication (or a digital multimeter) to monitor the VIN current. If the current becomes high, reduce the VIN voltage quickly to prevent damage. Then inspect the setup for any wiring errors.
- Use a digital multimeter to check the Standby supply current at VIN. For conditions of VIN = 3.6V in Standby mode, it should be below 2A.
- Connect the Stemma QT 4-wire cable (GND, SDA, SCL) to the KTD2690 evaluation board connector CN3, as shown in the Typical Test Setup Figure below.
- Connect the other end of the Stemma QT 4-wire cable to the MCP2221A USB to I2C interface board.
- Connect the MCP2221A board to a computer via the USB type-C cable.
- Connect the MCP2221A board output G0 to the KTD2690 board STROBE testpoint via the wire (STROBE) cable.
- Install GUI software.
Graphical User Interface (GUI)
- Download and install GUI software located on EVAL Kit Page (https://www.kinet-ic.com/ktd2690evab-mmev01/
- After installing software, the interface will appear with the status message “USB Device Attached” at the bottom left side of the window.
- If the displayed message is “USB Device Detached”, make sure the computer is properly connected to the board.
Typical Test Setup Diagram
Use the following test setup for the Quick-Start Procedures.
Graphical User Interface
(GUI) Window
To Check the I2C Connection to the Device
- In the “Reg 0x06 Device ID Register” section, click on the “Read 0x06” button.
- The GUI should display the Device ID equal to 001.
- If the device is not responding (I2C engine timeout), make sure VIN are powered from the 3.6V supply.
To Turn on Flash Mode by I2C Command for 1000ms Duration at 375mA Flash Current
- Set the Flash Current Code in Reg 0x03 register section by selecting “0x1F: 375mA” in the “LED Flash Current Code” list. Then click on “Write 0x03” button.
- Turn on Flash Mode in Reg 0x01 register section by selecting “11: Flash Mode” in the Mode Setting list, and then click on “Write 0x01” button.
- The LED current can be measured briefly by connecting a digital multimeter on P5 header across R3 0.1Ω resistor and GND. For 375mA, the voltmeter should measure a voltage around 38mV.
Electrical Schematic
Bill of Materials (BOM)
Line #| Quantity| Designator| Description| Value| Package| Manufacturer|
Manufacturer Part Number| Digikey Part Number| Mouser Part Number
---|---|---|---|---|---|---|---|---|---
1| 1| C1| CAP 100uF 10V X5R 1206| 100uF| 1206| Murata| GRM31CR61A107ME05L| 490
-GRM31CR61A107ME05LTR-ND| 81-GRM31CR61A107ME5L
2| 1| C2| CAP 10uF 16V X5R 0603| 10uF| 0603| Murata| GRM188R61C106MA73D|
490-7201-1-ND| 81-GRM188R61C106MA3D
3| 1| C3| CAP 10uF 16V X5R 0805| 10uF| 0805| Murata| GRM21BR61C106KE15L|
490-3886-1-ND| 81-GRM21BR61C106KE15
4| 1| CN3| CONN HEADER SMD R/A 4POS 1MM| | | JST Sales America Inc.| SM04B-
SRSS-TB(LF)(SN)| 455-1804-1-ND|
5| 1| D1| LED SST20 WHITE| | SMD| Luminus
Devices Inc.
| SST-20-WCS-B120-L4651| 1214-SST-20-WCS-B120-L4651CT-ND| 896-20WCSB120L4651
6| 1| L1| FIXED IND 1UH 2.9A 48
MOHM SMD
| 1uH| | Murata
Electronics
| DFE201612E-1R0M=P2| 490-16593-1-ND|
7
| ****
2
| ****
P1, P4
| CONN HEADER VERT 6POS 2.54MM| | Through Hole| Sullins Connector
Solutions
| ****
PREC002SAAN-RC
| ****
S1012EC-02-ND
|
8| 1| P3| CONN HEADER VERT
3POS 2.54MM
| | Through
Hole
| Sullins| PREC003SAAN-RC| S1012EC-03-ND|
9
| ****
1
| ****
P5
| CONN HEADER VERT 2POS 2.54MM| | Through Hole| Sullins Connector
Solutions
| ****
PREC002SAAN-RC
| ****
S1012EC-02-ND
|
10| 2| R1, R2| RES 47K 1% 1/10W 0603| DNP| 0603| Yageo| RC0603FR-0747KL|
311-47.0KHRCT-ND| 603-RC0603FR-0747KL
11| 1| R3| RES 0.1 OHM 1% 1/10W
0603
| 0.1R| 0603| Yageo| RL0603FR-070R1L| 311-.10QCT-ND| 603-RL0603FR-070R1L
12| 2| TP1, TP2| TERM TURRET SINGLE
L=5.56MM TIN
| | 1POS| Keystone| 1502-2| 36-1502-2-ND| 534-1502-2
13| 1| TP3| PC TEST POINT MULTIPURPOSE RED| | Through Hole| Keystone| 5010|
36-5010-ND| 534-5010
14| 3| TP4, TP5, TP6| PC TEST POINT MULTIPURPOSE BLACK| | Through Hole|
Keystone| 5011| 36-5011-ND| 534-5011
15
| ****
1
| ****
U1
| Inductorless, Single Flash LED Driver with Programmable 1.5A
Current Source
| | | ****
Kinetic Technologies
| ****
KTD2690EVAB-TR
| |
Printed Circuit Board (PCB)
Additional Test Procedures
To Turn on Torch Mode by I2C Command at 103mA Torch Current
- Set the Torch Current Code in Reg 0x04 register section by selecting “0x22: 103mA” in the “LED Torch Current Code” list. Then click on “Write 0x04” button.
- Turn on Torch Mode in Reg 0x01 register section by selecting “10: Torch Mode” in the Mode Setting list, and then click on “Write 0x01” button.
- The LED current can be measured by connecting a digital multimeter on P5 header across R3 0.1Ω resistor and GND. For 102mA, the voltmeter should measure a voltage around 10mV.
- Turn off Torch Mode in Reg 0x01 register section by selecting “00: Standby” in the Mode Setting list, and then click on “Write 0x01” button.
Troubleshooting
Symptom | Root Cause | Solution |
---|---|---|
“USB Device Detached” displayed on the bottom left of the GUI | MPC2221A board | |
not plugged in to computer or to the EVB | Make sure the MPC2221A board is |
connected to the computer via the USB cable.
Device is not responding to I2C command| MPC2221A board not plugged in to
computer or to the EVB| Make sure the MPC2221A board is connected to EVB
SDA/SCL/GND connector header CN3, and the USB cable is plugged into the
computer.
Device is not responding to I2C command| KTD2690 evaluation board VIN supply
is not powered| Make sure the KTD2690 board VIN testpoint is powered from an
external power supply.
LED is not turning on in Flash mode or in Torch mode| LED not connected on the
board| If using the on-board LED D1, make sure the jumper P4 is present.
Important Notices
Legal notice
Copyright © Kinetic Technologies. Other names, brands and trademarks are the
property of others.
Kinetic Technologies assumes no responsibility or liability for information
contained in this document. Kinetic Technologies reserves the right to make
corrections, modifications, enhancements, improvements, and other changes to
its products and services at any time and to discontinue any product or
services without notice. The information contained herein is believed to be
accurate and reliable at the time of printing.
Reference design policy
This document is provided as a design reference and Kinetic Technologies
assumes no responsibility or liability for the information contained in this
document. Kinetic Technologies reserves the right to make corrections,
modifications, enhancements, improvements, and other changes to this reference
design documentation without notice.
Reference designs are created using Kinetic Technologies’ published
specifications as well as the published specifications of other device
manufacturers. This information may not be current at the time the reference
design is built. Kinetic Technologies and/or its licensors do not warrant the
accuracy or completeness of the specifications or any information contained
therein.
Kinetic Technologies does not warrant that the designs are production worthy.
Customer should completely validate and test the design implementation to
confirm the system functionality for the end use application.
Kinetic Technologies provides its customers with limited product warranties,
according to the standard Kinetic Technologies terms and conditions.
For the most current product information visit us at www.kinet-
ic.com
Life support policy
LIFE SUPPORT: KINETIC TECHNOLOGIES’ PRODUCTS ARE NOT DESIGNED, INTENDED, OR
AUTHORIZED FOR USE AS COMPONENTS IN LIFE SUPPORT DEVICES OR SYSTEMS. NO
WARRANTY, EXPRESS OR IMPLIED, IS MADE FOR THIS USE. AUTHORIZATION FOR SUCH USE
SHALL NOT BE GIVEN BY KINETIC TECHNOLOGIES, AND THE PRODUCTS SHALL NOT BE USED
IN SUCH DEVICES OR SYSTEMS, EXCEPT UPON THE WRITTEN APPROVAL OF THE PRESIDENT
OF KINETIC TECHNOLOGIES FOLLOWING A DETERMINATION BY KINETIC TECHNOLOGIES THAT
SUCH USE IS FEASIBLE. SUCH APPROVAL MAY BE WITHHELD FOR ANY OR NO REASON.
“Life support devices or systems” are devices or systems which (1) are
intended for surgical implant into the human body, (2) support or sustain
human life, or (3) monitor critical bodily functions including, but not
limited to, cardiac, respirator, and neurological functions, and whose failure
to perform can be reasonably expected to result in a significant bodily injury
to the user. A “critical component” is any component of a life support device
or system whose failure to perform can be reasonably expected to cause the
failure of the life support device or system, or to affect its safety or
effectiveness.
SUBSTANCE COMPLIANCE
Kinetic Technologies IC products are compliant with RoHS, formally known as
Directive 2002/95/EC of the European Parliament and of the Council of 27
January 2003 on the restriction of the use of certain hazardous substances in
electrical and electronic equipment. However, this evaluation kit does not
fall within the scope of the EU directives regarding electromagnetic
compatibility, restricted substances (RoHS), recycling (WEEE), FCC, CE or UL,
and may not meet the requirements of these or related directives. To the best
of our knowledge the information is true and correct as of the date of the
original publication of the information. Kinetic Technologies bears no
responsibility to update such statement.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>