Sungale A10 Multi-Function Jump Starter User Manual

Sungale A10 Multi-Function Jump Starter

Functional diagram

1. Emergency Lights
2. Start Port
3. Main switch
4. DC charging port
5. Display Screen
6. Function Key
7. TYPE-C charging port
8. USB output port

Technical parameters

• Model: A10
• Size: 1687838mm
• Input: 5V~2A 9Vm2A 14V?1A
• USB Port: 5Vm3A (2A+1Al
• Applicable models: 12V
• Starting current: 400A
• Peak current: 800A
• Applicable temperature: -30-65″C

Car started steps

Important reminder

1. Do not reverse the starting steps of the car;
2. The metal head of the battery clamp and the metal wires on the positive and negative poles of the battery should be fully contacted, and dust or rust should be cleaned first.
3. After confirming that the electric quantity meets the starting conditions, the Start engine shall be operated only when the main power switch is turned off and shall be turned on again when the electric quantity needs to be confirmed next time.
4. If the battery is too low or has no electricity, disconnect the negative connection line of the battery and connect the positive and negative connection lines with clips to achieve a better starting effect. (Remember: the positive and negative wires must not be connected by mistake! )

Startup of five-prevention smart clamp

1. Please make sure that the electric quantity is not less than 60%, and the startup is prohibited below 60% (starting the car at full power as much as possible will ensure the service life of the power supply). Insert the smart clamp into the power supply (insert the plug firmly). At this time, the traffic lights on the clamp will flash alternately.
2. Clamp the red clamp to the positive(+) pole of the battery and the black clamp to the negative(-) pole of the battery. The intelligent clamp can be started when the green light is on for a long time.
3. Please operate and start the car within 30 seconds, otherwise, the power will be cut off automatically, and the red light on the clamp will be on for a long time with an alarm sound.
4. Remove the battery clamp and start the power supply within 20 seconds after starting. It is forbidden to insert the battery clamp into the power supply for a long time.
5. Cannot exceed 3 seconds for the Start engine. If the start-up is unsuccessful, please remove it from the car and wait for 2-3 minutes (after the temperature of the clamp drops) and then restart the connection.

Ordinary Battery Clamp Starts Car

1. Please make sure that the electric quantity is not less than 60%, and the starting is forbidden if the electric quantity is less than 60% (starting power supply starts the car at full power state as much as possible, which will ensure the service life of the power supply). Insert the ordinary clip into the power supply (insert the plug as hard as possible).
2. Clamp the red clamp to the positive(+) pole and the black clamp to the negative(-) pole of the battery.
3. Please operate and start the car within 30 seconds.
4. Remove the battery clip and start the power supply within 20 seconds after starting. It is forbidden to insert the battery clip into the power supply for a long time.
5. Cannot exceed 3 seconds for the Start engine. If the start-up is unsuccessful, please remove it from the car and wait for 2-3 minutes (after the temperature of the clip protection module decreases) before reconnecting and starting.

Functional operation instructions

Main switch instructions
The main switch controls the function of the entire board (the power start Port is not controlled by the main switch, Before starting the car, please turn off the main switch and push it to the OFF side.) Before charging, please turn on the main switch and push it to the ON side to connect the charger to charge the power supply; When not in use, please turn off the main switch and push it to the OFF side to reduce power loss.

Instructions for Using Function Key
On the premise of turning on the main switch, press the function key once to display the power quantity. After the screen is lit, press the function key for 3 seconds to turn on the illuminating lamp, and then press it for a short time to switch the illuminating mode, which is: strong light, flash, SOS, and off.

Description of electric quantity display
The LCD display screen displays 0-100% digitally.
Charging Display : When charging is connected, the display IN blinks, and the electricity quantity number indicates the current electricity quantity. Discharge display: power on displays the current power OUT, USB output displays OUT 5V2.1A.

Description of charge and discharge

This product has built-in boost voltage, supports 5V2A, 9V2A, and 14V1A charging input, and supports 5V3A (2A+1A) output. When charging, be sure to use a regular charger that matches its parameters. Do not use the inferior charger to charge, otherwise, safety accidents may occur. Please do not connect the overpowering products when outputting USB.

Toxic and Harmful Substances
O: indicates all homogeneous materials’ hazardous substance content is below the MCV limit specified in the standard (EU)2015/863.

Warning

1. The emergency starting operation steps of the car cannot lie in reverse
2. In case •f failure, please contact the dealer for handling. It is forbidden to disassemble the main machine without authorization; otherwise, safety accidents may be caused.
3. The positive and negative poles of the power supply are prohibited from butt joint, reverse connection er indirect short circuit; otherwise, safety accidents will be caused.
4. When using or charging, please stop using and consult customer service if any abnormal situation is found.
5. Please keep away from high temperatures or humid environments, and do not place it in direct sunlight.
6. Children are prohibited from contacting this product to avoid safety accidents.
7. When charging the product, please put it in an empty place and have an adult look after it.
8. Please be sure to read the instructions and follow them. If you have any questions, please contact customer service at any time. It is strictly prohibited to disassemble, puncture, refit, short-circuit the product or put it into water, fire or expose it to an environment ° with a temperature higher than 65 C to avoid damage to the product or other hazards.
9. 10. Do not clamp battery clamps or connect the positive and negative electrodes directly or indirectly with conductors to avoid safety accidents

Maintenance tips

1. This product can effectively deal with car start-u11 failure caused by s11erallic 11relllems of car batteries such as insufficient electricity and low temperature. However, it can only be used as emergency equipment and cannot replace the frequent use of car batteries or professional rescue. If the battery is aged, please replace the new battery in time after starting the car. After the car starts, please replenish the electricity in time for the next use.
2. Do not start the car at less than 60% of the power, otherwise, it will easily lead to over-discharge of the battery and damage te the latte cere.
3. The last way te maintain the emergency starting power supply for automobiles is to use it lightly and charge it quickly. The 9reater the frequency and number ef times it is used, the faster the battery will lose. The smaller the degree of deep discharge of the startin9 the longer the use time. If 11essillle, aveill fre11uent full char and discharge.
4. The startup port is the direct output port of the battery. It is not protected and must not be directly connected to products without voltage protection. Otherwise, the products and power supply may be damaged.
5. When not in use for a long period of time (more than 15 days), the battery has self-consumption, which requires regular checks to maintain a certain amount of electricity and charge and discharge at least once a month. Otherwise, the power supply may be damaged.

Warranty Statement

1. Within 7 days from the next day when you sign for the product, if the product has any quality problem caused by non-human reasons, you can enjoy the service of return and replacement without reason after being confirmed by the manufacturer.
2. Within 8-15 days from the next day when you sign for the product, if the product has any quality problem caused by non-human factors, you can enjoy free replacement or maintenance service upon confirmation by the manufacturer.
3. Within 12 months from the day after you sign for the product (within 3 months for accessories), if there is any product quality problem caused by non-human factors, you can enjoy free maintenance service upon confirmation by the manufacturer.

Non-warranty Regulations

1.  Unauthorized maintenance, misuse, collision, negligence, abuse, excessive discharge, liquid intake, accident, alteration, incorrect use of non-product accessories or accessories that do not conform to parameters, tearing up, altering labels and production dates.
2. The validity period of three guarantees has expired
3. Damage caused by force majeure.
4. Performance failure of this product and accessories is caused by human factors.
5. Do not operate or maintain according to instructions.
6. Normal battery loss and performance degradation caused by power supply usage.

Warranty Card

For warranty service, please show this warranty card and fill in the relevant contents in detail. The manufacturer provides warranty service to the purchasing customer for 12 months from the next day when the product is received, and 3 months for accessories. For products that are not covered by the warranty, our company can provide maintenance services, but the maintenance expenses and round-trip freight shall be borne by the customer.
Note : This product is for commercial use and only provides a one-month warranty service.

Implementation standards: GB4943.1-2011 GB31241-2014

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>