FLYCAM VSTA-II-AV Stabilizer Arm & Vest User Manual
- June 4, 2024
- FLYCAM
Table of Contents
VSTA-II-AV Stabilizer Arm &
Vest User Manual
What’s In The Box
Please inspect the contents of your shipped package to ensure you have received everything that is listed below.
All rights reserved.
No part of this document may be reproduced, stored in a retrieval system, or
transmitted by any form or by any means, electronic, mechanical, photocopying,
recording, or otherwise, except as may be expressly permitted by the
applicable copyright statutes or in writing by the Publisher.
Safety Hints
ATTENTION: PLEASE READ THIS BEFORE USING IT TO PREVENT SERIOUS DAMAGE TO
THE GEAR!
BE WATCHFUL OF THE HANDS
Cautiously operate to avoid pinching your hand/fingers inside the arm.
ALWAYS ESTABLISH THE CORRECT BALANCE Adjust the weight balance before
telescoping the length.
NEVER LEAVE THE FIXTURES LOOSE
All the knobs/screws must be locked tightly to avoid unbalancing of the whole
camera setup.
BE HIGHLY VIGILANT WHILE ASSEMBLING
Lack of attention while attaching Stabilizer, Arm & Vest together can cause
substantial damage to equipment.
NEVER LEAVE THE ARM UNATTENDED
Don’t let an unloaded arm swing about as it may hit you or someone near you.
FOLLOWING THESE GUIDELINES WILL PROVIDE BETTER SHOTS AND TROUBLE-FREE
OPERATION.
SHOULD YOU NEED ADDITIONAL INFORMATION, TECHNICAL ASSISTANCE IS AVAILABLE
‘ONLINE’ BY CONTACTING OUR SALES REPRESENTATIVE.
Vista-II Vest Setup
-
Attach both parts of the Jacket by attaching the top shoulder buckles (Part-1a) with (Part-1).
-
Follow the same step on another side. Then wear the jacket/vest.
-
After wearing the vest, attach the waist buckles (Part-1a) with (Part-1) on both sides.
-
Now attach the Hip Pad (Part-2) from both sides by attaching the buckles with (Part-1)
-
Then tighten the strap properly.
-
The length of the chest plate (Part-1) can be adjusted according to the height of a person.
-
Then Use the pin & knob (Part-1), as shown in the image.
-
You can also adjust the height of the Socket Block (Part-1).
-
Adjust the Height provided with the knob.
-
You can also remove the Socket Block (Part 1)
-
Adjust to left and right position with the pro- vided knob as shown in the image.
NOTE: It can be operated efficiently either right or left-handed. -
Loosen the knobs of the Socket Block on Vest (Part-1).
-
Then Insert the male connecting socket of Arm (Part-3) into the Socket Block of the Vest (Part-1).
-
After tightening both knobs of Socket Block on Vest (Part 1) to secure the section. NOTE: Adjust the ‘forearm’ (section nearest to Stabilizer) first, then the ‘upper arm’ section.
-
You can adjust the tension of the Arm (Part-3) with a mounted Stabilizer, by providing a knob, according to your setup requirement.
-
Adjust the lift with the Arm angled slightly up, and the knob will turn easily. Both Arm sections should track together.
NOTE: 17. For attaching the Stabilizer to Arm & Vest, keep the handle of the Stabilizer straight in accordance with the pin of the Arm.
18. There is a 16mm mounting post and we are giving 19 and 22mm bush, so you can easily mount the stabilizer (Not Included) on the mounting post of the arm according to your requirement. -
Insert bush (Part-4) on arm mounting post (Part-3)
-
Then insert it into the handle of your stabilizer.
To Use As Single Arm Configuration -
Pull the pin from the middle jointer.
-
Remove one section of the Arm (Part 3).
-
Now, attach the single arm (Part 3)
-
Insert the pin from the middle jointer to secure it.
-
Finally, the single arm (Part-3) is properly attached as shown in the image.
Arm Adjustment
The arm tension is adjusted for the heaviest camcorder it can hold, so it does
not bottom out when you put the camcorder and sled on it for the first time.
Now adjust the Arm for the weight of your camcorder:
- With the Vest On, attach Arm & unlock the rig.
- Move Arm to the middle of its booming (up and down) range and let go (If it stays where it is, you are probably close to the right adjustment).
- Keep making small adjustments until the camcorder does not rise or fall when you let go of it in the middle of its booming range.
Position arm
- Move the camcorder to your left so the arm crosses your body.
- Adjust the arc of your arm so the rig feels comfortable to you.
- Keep the camcorder close to your body.
For Interchanging the Spring, Follow this video https://bit.ly/3eYzHs6
Maintenance
Bearing Maintenance
If after some period of time the bearings stop running smoothly as when new,
you can oil it with light lubricating oil. We recommend using only a few
drops, anything more than a little will end up dripping from the bearing and
onto the rest of your Arm. Be sure to keep the oil away from your Camera, and
clean up any over-spill when done.
Cleaning
Do not use solvents or harsh cleaners of any kind on Vista-II Arm & Vest. If
the unit becomes dirty, use only a cloth or sponge with water and a very mild
detergent to gently rub the unit clean. Rinse well.
Storage
If you are going to store Flycam Vista-II Arm & Vest for a long period of
time, then we recommend storing it upright in a dry or low-to-normal humidity
area.
If you are unable to find an environment like this, then we suggest you store
the unit in an airtight plastic container or bag. Keeping the unit upright
helps to lessen stress on the system.
YOUR VISTA-II STABILIZER ARM & VEST ARE ALL DRESSED UP AND READY TO GO!
(SHOWN WITH OPTIONAL ACCESSORIES)
Warranty: We offer one year warranty for our products from date of
purchase. Within this period of time, we will repair it without charge for
labor or parts. Warranty doesn’t cover transportation costs nor does it cover
a product subjected to misuse or accidental damage. Warranty repairs are
subjected to inspection and evaluation by us.
Liability: We are not liable for damage caused by products that we do not
supply or from mishandling in transit, accident, misuse, neglect, lack of care
of the product, or service by anyone other than our company.
Contact Us: In case of any kind of dissatisfaction, please Contact us
immediately and we promise our utmost support and care until you use our
product.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>