Shark Navigator NV60 Upright Vacuum Cleaner Owners Guide

Shark Navigator NV60 Upright Vacuum Cleaner Owners Guide

IMPORTANT SAFETY INSTRUCTIONS

For Household Use Only
WHEN USING YOUR SHARK® NAVIGATOR® VACUUM, BASIC SAFETY PRECAUTIONS SHOULD ALWAYS BE FOLLOWED, INCLUDING THE FOLLOWING: READ ALL INSTRUCTIONS BEFORE USING YOUR SHARK® NAVIGATOR® VACUUM.

POLARIZED PLUG
This appliance has a polarized plug (one blade is wider than the other). As a safety feature, this plug will fit into a polarized outlet only one way. Do not force into the outlet or try to modify the plug to fit.

WARNING:
TO REDUCE THE RISK OF ELECTRIC SHOCK OR INJURY DO NOT USE OUTDOORS OR ON WET SURFACES.

WARNING:
TO REDUCE THE RISK OF FIRE, ELECTRIC SHOCK, OR INJURY

GENERAL ELECTRICAL SAFETY:

1. Unplug from the electrical outlet when not in use and before servicing.
2. DO NOT use a vacuum with a damaged cord or plug. If an appliance is not working as it should, has been dropped, damaged, left outdoors, or dropped into water, return it to SharkNinja Operating LLC for examination, repair, or adjustment.
3. DO NOT pull or carry the vacuum by the cord.
4. DO NOT unplug by pulling on the cord; to unplug, grasp the plug, not the cord.
5. D O NOT handle plugs or appliances with wet hands.
6. DO NOT run the vacuum over the power cord.
7. DO NOT use the cord as a handle.
8. DO NOT close a door on the cord.
9. DO NOT pull the cord around sharp corners. The use of an extension cord is not recommended.
10. DO NOT leave the appliance when plugged in.
11. Keep the cord away from heated surfaces.
12. Turn off all controls before plugging or unplugging the vacuum cleaner.
13. Always turn off this appliance before connecting or disconnecting the motorized nozzle.
14. Store your appliance with the power cord secured around the two cord holders as shown in the storage instructions.

HOSE ATTACHMENTS

1. DO NOT use if airflow is restricted; if the air paths, the hose, or the accessories become blocked, turn the vacuum cleaner off. Remove all obstructions before you turn on the unit again.
2. Keep the end of the hose and accessory openings away from the face and body.
3. Keep cleaning tools and hose suction openings away from hair, face, fingers, uncovered feet, or loose clothing.
4. Only use the manufacturer’s recommended attachments.

GENERAL USE:

1. Use only as described in this manual.
2. DO NOT put any objects into openings. DO NOT use with any opening blocked; keep free of dust, lint, hair, and anything that may reduce airflow.
3. Keep your work area well-lit.
4. Keep the vacuum moving over the carpet surface at all times to avoid damaging the carpet fibers.
5. DO NOT place a vacuum on unstable surfaces such as chairs or tables.
6. DO NOT allow young children to operate the vacuum or use as a toy. Close attention is necessary when used near children.
7. DO NOT use a vacuum cleaner if it has been dropped, damaged, left outdoors, or submerged in water. Return to SharkNinja Operating LLC for examination, repair, or adjustment.
8. DO NOT use without a dust cup and/or filters in place.

DUST CUP/FILTERS/ACCESSORIES:
Before turning on the vacuum:

1. Make sure that all filters are thoroughly dry after routine cleaning.

2. Make sure that the dust cup and all filters are in place after routine maintenance.

3. Make sure accessories are free of blockages.

4. Only use filters and accessories provided by SharkNinja Operating LLC. [Failure to do so will void the warranty.]

GENERAL CLEANING

1. DO NOT pick up large-sized objects.
2. DO NOT pick up hard or sharp objects such as glass, nails, screws, or coins that could damage the vacuum cleaner.
3. DO NOT pick up smoking or burning objects such as hot coals, cigarette butts, fireplace ash or matches.
4. DO NOT use to pick up drywall dust.
5. DO NOT pick up flammable or combustible materials such as lighter fluid, gasoline, or kerosene, or use a vacuum in areas where they may be present.
6. DO NOT pick up toxic solutions such as chlorine bleach, ammonia, or drain cleaner
7. DO NOT use in an enclosed space where vapors are present from paint, paint thinner, moth-proofing substances, flammable dust, or other explosive or toxic materials.
8. DO NOT vacuum up any liquids.
9. DO NOT immerse the vacuum cleaner in water or other liquids.
10. DO NOT use outdoors or on wet surfaces; use only on dry surfaces.
11. Use extra care when cleaning on stairs.

Getting Started

WHAT’S IN THE BOX YOU JUST OPENED:

• Vacuum Body
• Floor Power Nozzle
• Handle Assembly
• Super Stretch Hose
• Cleaning Wand
• Wide Upholstery Tool
• Dusting Brush
• Crevice Tool

Your Shark® Navigator® is easy to assemble

1. Lay your vacuum body on a level surface.

2. Slide the electrical connection from the power nozzle into the main body to click into place.

3. Connect the hose from the main body to the power nozzle; push with a slight turning motion to create a snug fit.

4. Slide the handle assembly into the upright unit aligning the hose hook on the handle assembly with the power cord hooks on the back of the unit

5. Your Shark® Navigator® is easy to assemble:

6. Lay your vacuum body on a level surface. Slide the electrical connection from the power nozzle into the main body to click it into place.

7. Connect the hose from the main body to the power nozzle; push with a slight turning motion to create a snug fit.

8. Slide the handle assembly into the upright unit aligning the hose hook on the handle assembly with the power cord hooks on the back of the unit

9. Attach the Super Stretch Hose:

   • Snap hose into the swivel connector
   • Route under the anti-tip hook to prevent a vacuum from tipping
   • The route over the upper hose holder
   • Press securely onto the cleaning wand with the handle
     IMPORTANT:
     Insert the hose into the wand. This completes the air path and enables suction to reach the Floor Power Nozzle.

10. To store the vacuum: When storing your vacuum, wind the cord around the two cord holders and secure with cord clip:

    • Quick Cord release at the top of the unit – place in the upright position.
    • Cord holder near the base – turn it until it is pointing down. To release the cord, turn the Quick Cord release to the left or right.

11. To store the vacuum: When storing your vacuum, wind the cord around the two cord holders and secure them with a cord clip

12.  Quick Cord release at the top of the unit – place in the upright position.

13. Cord holder near the base – turn it until it is pointing down.

14. To release the cord, turn the Quick Cord release to the left or right.

Using the Vacuum

IMPORTANT: To protect your carpets, the brush roll will only turn on when you have pulled the handle back towards you and released the Floor Power Nozzle. Release suction for easier push and pull on high-pile carpets
and area rugs. Your Shark® Navigator® Vacuum can be used to clean bare floors or carpets – with the click of a switch. Stand the vacuum in the upright position.

Plug in the vacuum

1.  Start with the Power Switch in the “O” – Off position.
2. Place your foot on the Floor Power Nozzle and pull the handle towards you.
3. Set the Power Switch to desired cleaning setting.
4. Push the power cord into the groove on the handle and then secure the power cord into the cord clip.
5. Press the On/Off switch to the“I” position to vacuum bare floors or clean with the hose (straight suction only) or to the “II” position to engage the motorized floor brush (for vacuuming carpets and rugs).
6. Due to the huge suction power of this vacuum, it may become necessary to adjust the suction release on the hose.
7. If the vacuum is difficult to push or pull or if it is lifting up area rugs, adjust the suction release by opening the valve at the top end of the hose. Close the suction release valve for maximum suction when vacuuming floors or when using the Wide Upholstery Tool.

IMPORTANT:
Your Brushroll Indicator Light will illuminate solid green when the brush roll is on, or solid red if there is a blockage. This feature is designed to protect your Lifetime A belt that powers your brush roll. See Checking for Blockages on page 11. NOTE: The height of your power nozzle has been optimized for easy pushing and superior cleaning on all floor types, so there is no need to make any height adjustments as you transition to different floor & carpet types.

Cleaning with the Vacuum Accessories

• Before cleaning with your accessories:
• Stand the vacuum in an upright position.
• Secure Super Stretch Hose in the anti-tip hose hook to prevent tipping.
• Select the “I” – On position for suction-only cleaning.
• DO NOT pull the vacuum cleaner around by the hose.
• DO NOT overextend the hose.

Before cleaning with your accessories
Stand the vacuum in an upright position.

• Secure Super
• Stretch Hose in the anti-tip hose
• hook to prevent tipping.
• Select the “I” – On position for suction-only cleaning.
• DO NOT pull the vacuum cleaner around by the hose.
• DO NOT overextend the hose.

Using the Cleaning Wand:
Stand the vacuum upright position.

1. Remove the Cleaning Wand (with a hose attached) from the unit.
2. Push the selected tool into the end of the Cleaning Wand.
3. Wide Upholstery Tool
4. Dusting Brush
5. Crevice Tool To order additional parts and accessories, go to www.sharkclean.com or call 1-800-798-7398.

Maintenance

For best results empty the Dust Cup Assembly after each use, as needed during prolonged usage or when it reaches the MAX fill line. DO NOT OVERFILL. Turn the vacuum off before emptying.

CAUTION:
Unplug the vacuum; failure to do so might result in an electric shock.

To empty the Dust Cup:

1. Grip the carry handle and press the Dust Cup release button to remove it.

2.  Option A: For Quick Empty: Insert Dust Cup deep inside trash receptacle to contain dust and debris.

3. Press the bottom Dust Cup release button; tap the container gently to dislodge and release dust and debris. Snap door in place.
   Important: If the Dust Cup

4. The door does not swing open after pressing the release button, push the door open using the bottom door tabs.

Option B :
For Allergy Sufferers: Wrap a trash bag around the Dust Cup leaving space at the bottom for the door to swing
open. Locate the Dust Cup Door release button within the trash bag and press to release as you shake the dust cup to empty dust and debris. Snap the bottom door in place.
Note: Option B can also be performed outside of the home to further minimize releasing dust back into the air. Carry just the Dust Cup and trash bag outside.

Note: Some dust and debris may remain in the top of your dust cup on or near the metal screen. It is not necessary to completely remove this material before continuing to vacuum; Shark® advanced cyclonic action will sweep the metal
screen clean once you begin to refill your dust cup.

• DO NOT operate the vacuum without ALL the filters in place.
  DO NOT operate the vacuum with WET filters.

IMPORTANT
Loss of Suction may occur if the foam filter is not cleaned every month. Rinse and allow to air dry completely. Also, tap loose dirt off the filter between washes as needed. Foam filters may appear dirty after use – this is normal.

To clean the pre-motor filters:

1.  Remove the dust cup.

2. Pull the 2 filters out from the top of the motor base.

3. Rinse the filters thoroughly in lukewarm water until the water runs clear. DO NOT put the filters in the washing machine or dishwasher.
   NOTE: The material in the filters will discolor over time. This is NORMAL and will not affect the performance of the filters.

4. Squeeze out excess water and let air dry for at least 24 hours before replacing. Do not use a hair dryer or other heating methods to dry.

5. Place the felt filter in first, then the foam filter.

6. Replace the dust cup

To clean the post-motor HEPA filter:

1. Remove the filter cover from the front of the vacuum by pulling up on the tab and pulling the cover away from the vacuum.

2. Take out the HEPA filter by pulling it straight out.

3. Turn the HEPA filter over so that the dirty side is on the bottom and vigorously tap it clean against a garbage can to remove any dust. Wash the HEPA filter under the tap using lukewarm water with the dirty side face down until the water runs clear. DO NOT put the HEPA filter in the washing machine or dishwasher.
   NOTE: The material in the filter will discolor over time. This is NORMAL and will not affect the performance of the filter.

4. Allow the HEPA filter to air dry for 24 hours. Do not use a hair dryer or other heating methods to dry.

5. Once the HEPA filter is dry, replace it back into the vacuum.

6. Replace the cover by inserting the two tabs into the holes at the bottom and then swinging the cover up until it clicks into place.

Troubleshooting

Vacuum is not picking up dirt.

| Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the vacuum. (See “Maintenance” sections for instructions.)

Dust cup may be full; empty dust cup.

Check hose and hose connections for blockages; clear blockages if required.

If dust cup is empty, and attachment inlets are clear, check for other blockages. (See “Checking for Blockages” for instructions.)

Vacuum lifts scatter rugs (lightweight, movable rugs).| Suction is powerful. Take care when vacuuming scatter-type rugs or rugs with delicately sewn edges. Open the suction release on the hose to decrease suction power.

Airflow is restricted. No suction or light suction.

| Check filters to see if they need cleaning. Follow instructions for rinsing and drying the filters before re-inserting back into the vacuum. (See “Maintenance” sections for instructions.)

Dust cup may be full; empty dust cup.

Check hose, hose connections, nozzles and accessories for blockages; clear blockages if required.

Close the suction release on the hose to increase suction power.

If dust cup is empty, and attachment inlets are clear, check for other blockages. (See “Checking for Blockages” for instructions.)

Motorized floor brush has become jammed or has shut off.| Immediately turn off and unplug vacuum, disconnect the nozzle and remove blockage before reconnecting and turning vacuum back on. (See “Checking for Blockages” for instructions.)

Vacuum turns off on its own.

| This vacuum cleaner is equipped with a motor protective thermostat. If for some reason your vacuum overheats, the thermostat will automatically turn the unit off. Should this occur, perform the following steps to restart the motor thermostat:

1. Move the On/Off switch to the “O” (Off) position.

2. Unplug the vacuum.

3. Empty the dust cup and clean filters. (See “Maintenance” sections for instructions.)

4. Check for blockages in hose, accessories and inlet openings. (See “Checking for Blockages” for instructions.)

5. Allow the unit to cool for a minimum of 45 minutes.

6. Plug in the vacuum.

7. Turn the On/Off switch to the “I” (On) position to restart the vacuum.

Note: If vacuum still does not start, contact Customer Service at:

1-800-798-7398.

WARNING:
To reduce the risk of electric shock, the power cord must be disconnected before performing maintenance/troubleshooting checks

Checking for Blockages

Unplug the vacuum before checking for blockages. Reassemble all parts securely before operating the vacuum Blockages may cause your vacuum to overheat and shut down. If so, clear the blockages, then follow the instructions for Resetting the Motor Thermostat on page 12.

WARNING: Never insert sharp objects into any opening to clear an obstruction.
IMPORTANT : Damages caused while clearing or attempting to clear blockages are not covered under your product’s limited warranty.

1. Dust Cup Air Duct: Stand vacuum into an upright position. Remove Dust Cup Assembly and empty Dust Cup if necessary. Disconnect the Super Stretch Hose. Check Air Duct behind Dust Cup for clogs; clear before replacing Dust Cup Assembly.
2. Intake Opening behind the Brushroll: Lay the vacuum flat to expose the brush roll. Check the opening behind the brush roll for clogs. Clear the opening. Clear the brush roll; use scissors to carefully cut away threads, hair, or other debris that might be trapped in the bristles.
3. Floor Power Nozzle Hose Connector: Lay the vacuum flat. Remove the Nozzle Hose and check for clogs. Push the Hose Connector back onto the Floor Power Nozzle.
4. Hose: Stand the vacuum upright. Remove the hose from both the unit and Cleaning Wand ends. Inspect both ends and the length of the hose for clogs. Return the hose to the unit.

Maintenance

Cleaning The Motorized Floor Brush When your motorized floor brush needs cleaning or locks onto an object, it automatically shuts down to prevent damage to your lifetime belt. The indicator light will illuminate red warning you to turn
off the vacuum and clear the blockage immediately. The light will reset itself once the blockage has been cleared and power has been cycled on/off or the vacuum has been locked in the upright position.

1. Detach the motorized floor brush from the detachable
   canister.

2. Inspect the opening underneath and the rotating brush. If a build-up of debris is present, remove it. Carefully cut anything wound around the rotating brush with scissors. Avoid damaging or cutting the bristles

Cleaning The Motorized Floor Brush When your motorized floor brush needs cleaning or locks onto an object, it automatically shuts down to prevent damage to your lifetime belt. The indicator light will illuminate red warning you to turn off the vacuum and clear the blockage immediately. The light will reset itself once the blockage has been cleared and power has been cycled on/off or the vacuum has been locked in the upright position.

1. Detach the motorized floor brush from the detachable canister.
2. Inspect the opening underneath and the rotating brush. If a build-up of debris is present, remove it. Carefully cut anything wound around the rotating brush with scissors. Avoid damaging or cutting the bristles

Cleaning The Motorized Floor Brush When your motorized floor brush needs cleaning or locks onto an object, it automatically shuts down to prevent damage to your lifetime belt. The indicator light will illuminate red warning you to turn
off the vacuum and clear the blockage immediately. The light will reset itself once the blockage has been cleared and power has been cycled on/off or the vacuum has been locked in the upright position.

1. Detach the motorized floor brush from the detachable canister.
2. Inspect the opening underneath and the rotating brush. If a build-up of debris is present, remove it. Carefully cut anything wound around the rotating brush with scissors. Avoid damaging or cutting the bristles

PART PART NO

• Super Stretch Hose 152FFJ
• Dusting Brush &
• Crevice Tool 1115FC
• Foam & Felt Filters XFF80
• Hepa Filter XHF80
• Wide Upholstery Tool 261FFJ46
• Cleaning Wand 114FFJ

FIVE (5) YEAR LIMITED WARRANTY

SharkNinja Operating LLC warrants this product to be free from defects in material and workmanship for a period of one (5) years from the date of the original purchase, when utilized for normal household use, subject to the following conditions, exclusions, and exceptions. If your appliance fails to operate properly while in use under normal household conditions within the warranty period, return the complete appliance and accessories, freight prepaid. For assistance with warranty service options or customer support, please call our customer care and product specialists at, call 1-800-798-7398 or visit our website www.sharkclean.com. If the appliance is found to be defective in material or workmanship, SharkNinja Operating LLC will repair or replace it free of charge. Proof of purchase is required and a fee of $19.95 will apply to cover the cost of return freight. *

The liability of SharkNinja Operating LLC is limited solely to the cost of the repair or replacement of the unit at our option. This warranty does not cover normal wear of parts and does not apply to any unit that has been tampered with or used for commercial purposes. This limited warranty does not cover damage caused by misuse, abuse, negligent handling or damage due to faulty packaging or mishandling in transit. This warranty does not cover damage or defects caused by or resulting from damages from shipping or repairs, service or alterations to the product or any of its parts, which have been performed by a repair person not authorized by SharkNinja Operating LLC.

This warranty is extended to the original purchaser of the unit and excludes all other legal and/or conventional warranties. The responsibility of SharkNinja Operating LLC warranty if any, is limited to the specific obligations expressly assumed by it under the terms of the limited warranty. In no event is SharkNinja Operating LLC liable for incidental or consequential damages of any nature whatsoever. Some states/provinces do not permit the exclusion or limitation of incidental or consequential damages, so the above may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province. *Important: Carefully pack items to avoid damage in shipping. Be sure to include proof of purchase date and to attach tag to the item before packing with your name, complete address and phone number with a note giving purchase information, model number and what you believe is the problem with the item. We recommend you insure the package (as damage in shipping is not covered by your warranty). Mark the outside of your package “ATTENTION CUSTOMER SERVICE”.

Product Registration

Please visit www.sharkclean.com or call 1-800-798-7398 to register your new Shark® product within ten (10) days of purchase. You will be asked to provide the store name, date of purchase and model number along with your name and address. The registration will enable us to contact you in the unlikely event of a product safety notification. By registering you acknowledge to have read and understood the instructions for use, and warnings set forth in the accompanying instructions.
SharkNinja Operating LLC
U.S.: Newton, MA 02459
Canada: Ville St. Laurent, Québec H4S 1A7 1-800-798-7398
www.sharkclean.com Copyright © SharkNinja Operating LLC 2016 Printed in China

Illustrations may differ from actual products. We are constantly striving to improve our products, therefore the specifications contained herein are subject to change without notice.For SharkNinja U.S. Patent information visit http://www.sharkninja.com/USPatents. Shark and Navigator are registered trademarks of SharkNinja Operating LLC. NV60_31_IB_E_160427_1

Download PDF:Shark Navigator NV60 Upright Vacuum Cleaner Owners Guide

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>