eufy S100 Wall Light Cam User Manual
- June 12, 2024
- Eufy
Table of Contents
eufy S100 Wall Light Cam User Manual
AT A GLANCE
Light- Camera Lens
- Status LED
- Motion Sensor
- Micro-USB Port
- Reset Hole
WHAT’S INCLUDED
SETTING UP THE SYSTEM
-
Open the USB port cover on the back of the device, then connect it to power with the provided cable. The status LED will display red when the device is ready for setup.
-
Download and install the eufy Security app, then set up an account.
https://play.google.com/store/apps/details?id=com.wenquan.euf11&hl=en_US
https://apps.apple.com/us/app/eufy-security/id1424956516
-
Scan the QR code on the back of the device, then follow the on-screen instructions to complete the setup.
-
Disconnect the device from power and close the USB port cover, then secure the rubber plugs.
INSTALLATION
1. Turn off the circuit breaker of your home. Turn the lights on and off to check the electricity in your home is properly turned off.
2. Select a location for the device and mark it.
For the best motion detection experience, install the device between 1.8m and
2m above the ground.
Do not install the device more than 2.2m above the ground.
3. If no wires exist, run wires to the installation location. Next, screw the mounting bracket onto the wall.
- On wooden walls, do not pre-drill holes. Use the screws provided to fix the mounting bracket onto the wall.
- For walls made of hard materials, such as stucco, brick, or concrete, pre-drill holes in the required locations, insert the provided anchors, and then use the provided screws to fix the mounting bracket to the wall.
4. Loosen the wire screws, insert the neutral, ground, and live wires into the connectors, and then tighten the wire screws to thoroughly secure the wires.
5. Mount the device onto the mounting bracket, and then secure it with a screw on each side.
6. Turn on the circuit breaker of your home.
ADJUSTING ANGLES
1. Turn the device while checking the live stream from the eufy Security app until you get the desired view.
2. Turn each light for different lighting effects.
SAFETY
-
This equipment is not suitable for use in locations where children are likely to be present. This equipment is not intended for use by children.
-
Do not use the product in any way other than described herein in order to avoid personal injury or property damage.
-
User should comply with the laws and regulations of the corresponding countries and regions where the equipment is located (used), abide by professional ethics, pay attention to safety obligations, and strictly prohibit the use of our products or equipment for any illegal purposes.
Our company will not be responsible for any violators’ legal liability under any circumstances. -
An appropriate disconnect device shall be provided as part of the building installation An all-pole mains switch in accordance with Annex L shall be incorporated in the electrical installation of the building
-
The luminaire internded to be mounted on or over an outlet box and shall be provided with supply conductors long enough to extend 150mm(6 in) into the outlet box.
-
Caution, risk of electric shock
-
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE INSTALLATIONCODE BY A PERSON FAMILIAR WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT ANDTHE HAZARDS INVOLVED
-
MIN 90°C SUPPLY CONDUCTORS
NOTICE
NOTICE (United States of America)
FCC Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2)this device must accept any interference received,
including interference that may cause undesired operation.
Warning : Changes or modifications not expressly approved by the party
responsible for compliance could void the user’s authority to operate the
equipment.
Note: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation.
This equipment generates uses and can radiate radio frequency energy and, if
not installed and used in accordance with the instructions, may cause harmful
interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception, which can be
determined by turning the equipment off and on, the user is encouraged to try
to correct the interference by one or more of the following measures: (1)
Reorient or relocate the receiving antenna. (2) Increase the separation
between the equipment and receiver. (3) Connect the equipment into an outlet
on a circuit different from that to which the receiver is connected. (4)
Consult the dealer or an experienced radio/TV technician for help.
FCC Radio Frequency Exposure Statement
The device has been evaluated to meet general RF exposure requirements.
Thedevice can be used in fixed/mobile exposure condition. The min separation
distanceis 20cm.
Notice: Shielded cables
All connections to other computing devices must be made using shielded cables
tomaintain compliance with FCC regulations.
The following importer is the responsible party
Company Name: POWER MOBILE LIFE, LLC
Address: 10900 NE 8th St, Ste 501, Bellevue WA 98004
Telephone:1-800-988-7973
NOTICE（Canada）
IC Statement
This device complies with Industry Canada licence-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
IC RF Statement
When using the product, maintain a distance of 20cm from the body to ensure
compliance with RF exposure requirements.
NOTICE (Europe and United Kingdom)
This product complies with the radio interference requirements of the European Community.
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance
with the essential requirements and other relevant provisions of Directive
2014/53/EU. Forthe declaration of conformity, visit the Web site:
https://uk.eufylife.com/
This product complies with the radio interference requirements of the United
Kingdom
Declaration of Conformity
Hereby, Anker Innovations Limited declares that this device is in compliance
with Radio Equipment Regulations 2017(SI 2017/1206). The full text of the UK
declaration of conformity is available at the following internet address:
https://uk.eufylife.com/Do not use the Device in the environment at too high
or too low temperature, never expose the Device under strong sunshine or too
wet environment.
The suitable temperature for the device and accessories is -20°C to 50°C.
It is recommended to supply the device in an environment with a temperature
that ranges from 5℃~25℃. When supplying, please place the device in an
environment that has a normal room temperature and good ventilation.
RF exposure information
The Maximum Permissible Exposure (MPE) level has been calculated based on a
distance of d=20 cm between the device and the human body. To maintain
compliance with RF exposure requirement, use product that maintain a
20cmdistance between the device and human body.
Frequency bands and power as below:
The following importer is the responsible party (contract for EU matters): Anker Innovations Deutschland GmbH I Georg-Muche-Strasse 3, 80807 Munich, Germany
The following importer is the responsible party (contract for UK matters): Anker Technology (UK) Limited I GNR8, 49 Clarendon Road, Watford, Hertfordshire, WD17 1HP, United Kingdom
This product is designed and manufactured with high quality material sand components, which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and
should be delivered to an appropriate collection facility for recycling.
Proper disposal and recycling helps protect natural resources, human health
and the environment. For more information on disposal and recycling of this
product, contact your local municipality, disposal service, or the shop where
you bought this product.
NOTICE (Australia)
Do not use the Device in the environment at too high or too low temperature,
never expose the Device under strong sunshine or too wet environment.
The suitable temperature for the device and accessories is -20°C to 50°C.
It is recommended to supply the device in an environment with a temperature
that ranges from 5℃~25℃. When supplying, please place the device in an
environment that has a normal room temperature and good ventilation.
This product is designed and manufactured with high quality materials and components, which can be recycled and reused.
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.
Anker Innovations Limited | Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon, Hong Kong
Customer Service
Service client
12-month limited warranty
(US) +1 800-988-7973
(UK) +44 (0) 1604 936200
(DE) +49 (0) 69 9579 7960
Anker Innovations Limited
Room 1318-19, Hollywood Plaza, 610 Nathan Road, Mongkok, Kowloon,
Hong Kong
Anker Innovations Limited. All rights reserved. eufy Security and eufy Security Logo are trademarks of Anker Innovations Limited, registered in the United States and other countries. All other trademarks are the property of their respective owners.
51005003643 V01
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>