Milwaukee M18TM FUEL Single Battery Brush Cutter Instruction Manual
- June 12, 2024
- Milwaukee
Table of Contents
BULLETIN NO.
54-49-3010
Instruction Manual
SERVICE PARTS LIST
SPECIFY CATALOG NO. AND SERIAL NO. WHEN ORDERING PARTS| REVISED BULLETIN| DATE
June 2023
---|---|---
M18™ FUEL Single Battery Brush Cutter
CATALOG NO.| 3015-20| STARTING SERIAL NO.| N46A| WIRING INSTRUCTION
EXAMPLE:
Component Parts (Small #)
Are Included When Ordering
The Assembly (Large #).
FIG. | PART NO. | DESCRIPTION OF PART | NO. REQ. |
---|---|---|---|
30 | 42-92-0099 | Extension Tube | 1 |
31 | 42-92-0122 | Tube Liner | 1 |
32 | 36-18-0022 | Spline Drive Shaft | 1 |
33 | 31-44-0297 | Handlebar w/Left Handle Assy | 1 |
35 | 05-88-1200 | M4 x 16mm Pan Hd. ST T-20 Screw | 7 |
36 | ————— | Right Handle Cover | 1 |
37 | 22-56-0063 | Wire Cover | 1 |
38 | 23-66-0207 | Trigger | 1 |
39 | ————— | Right Handle Halve-Support | 1 |
40 | 40-50-0218 | Torsion Spring | 1 |
41 | 31-76-0026 | Trimmer Lockout | 1 |
42 | 22-44-0015 | Handlebar Loom Clip | 1 |
43 | 06-82-0154 | M3 x 10mm Pan Hd. ST T-10 TP Screw | 2 |
44 | 05-77-0013 | Wing Screw | 1 |
45 | 28-10-0017 | Top Clamp | 1 |
46 | 40-50-0479 | Clamp Spring | 1 |
47 | 28-10-0019 | Bottom Clamp | 1 |
48 | 05-74-0246 | M6 x 16mm Pan Hd. T-30 Mach. Screw | 4 |
49 | 05-74-0249 | M4 x 20mm Pan Hd. T-20 Machine Screw | 1 |
50 | 45-88-0379 | Washer | 1 |
51 | ————— | Motor Mount | 1 |
52 | 05-88-0032 | M4 Hex Nut | 1 |
53 | 42-06-0048 | Drive Shaft Coupling | 1 |
54 | ————— | Motor Insulator – Bottom | 1 |
55 | ————— | Rotor | 1 |
56 | ————— | Ball Bearing | 1 |
57 | ————— | Motor Insulator – Top | 1 |
58 | ————— | M3.0 x 14mm Pan Hd. T-10 ST Screw | -6 |
59 | ————— | PCBA | -1 |
60 | 06-82-0053 | M2.6 x 8mm Pan Hd. Tapt. T-8 Scr. | -3 |
62 | ————— | Lower Housing-Right | -1 |
FIG. | PART NO. | DESCRIPTION OF PART | NO. REQ. |
--- | --- | --- | --- |
63 | ————— | Motor Housing-Right | 1 |
64 | ————— | Motor Housing-Left | 1 |
65 | ————— | Lower Housing-Left | 1 |
66 | 05-88-1200 | M4 x 16mm Pan Hd. ST T-20 Screw | 7 |
67 | 05-88-1300 | M4 x 1.4 x 28mm Pan Hd. ST T-20 Screw | 3 |
68 | 44-52-0001 | Rubber Pad with Adhesive (Set of 2) | 1 |
69 | 42-70-0079 | M3 x 22mm Pan Hd. ST T-10 Screw | 2 |
70 | 28-10-0022 | Wire Clamp | 1 |
71 | 05-74-0315 | M5 x 17mm Pan Hd. T-25 Machine Screw | 1 |
72 | 28-10-0021 | Tube Clamp | 1 |
73 | 06-82-7240 | 6-19 x 1/2” Pan Hd. ST T-15 Screw | 4 |
75 | 23-94-0073 | Harness Loop Band | 1 |
76 | 05-74-0238 | M6 x 14mm Pan Hd. T30 Screw | 1 |
77 | 42-70-0082 | Loom Clip | 3 |
80 | 28-10-0023 | Bottom Clamp Cap | 1 |
85 | 23-94-0511 | Dual Strap Harness | 1 |
86 | ————— | Stator | 1 |
90 | 34-60-0066 | E-Ring | 1 |
92 | 10/20/9887 | Warning Label (not shown) | 1 |
94 | 12-20-0582 | Service Nameplate (not shown) | 1 |
100 | 31-44-0701 | Housing Kit | 1 |
101 | 31-50-0023 | Motor Insulator Kit | 1 |
103 | 16-01-0036 | Rotor Assembly | 1 |
105 | 31-44-0713 | Handle/Trigger Kit | 1 |
106 | 31-44-0708 | Handle Attachment Kit | 1 |
107 | 31-44-0706 | Lower Housing Kit | 1 |
108 | 42-92-0121 | Tube Kit | 1 |
109 | 14-20-0412 | Electronics Assembly | 1 |
MILWAUKEE TOOL l www.milwaukeetool.com
13135 W. Lisbon Road, Brookfield, WI 53005
Drwg. 2
FIG. | PART NO. | DESCRIPTION OF PART | NO. REQ. |
---|---|---|---|
1 | 14-46-0423 | Trimmer Head, Easy Load | 1 |
9 | 42-26-0024 | Cutoff Line Blade | 1 |
10 | 05-74-0935 | M5 x 15mm Pan Hd. T-25 Machine Screw | 2 |
11 | 28-28-0039 | String Trimmer Guard w/ Captive Screws | 1 |
13 | 05-81-0131 | M6 x 17.8mm Flat Hd. Hex Mach Screw | 1 |
14 | 05-74-0084 | M6 x 4mm Pan Hd. T-30 Captive Screw | 8 |
15 | 28-28-0044 | Lock Plate Assembly | 1 |
16 | 31-01-0042 | Gearbox | 1 |
23 | 05-74-0015 | M6 x 21.5mm Cap Hd. T-30 Mach Screw | 2 |
81 | 31-10-0019 | Blade Mount Assembly | 1 |
82 | 05-74-0313 | Hexagon Nut | 1 |
83 | 28-41-0022 | Brush Cutter Guard | 1 |
84 | 49-16-2757 | Brush Cutter Blade | 1 |
97 | 45-96-0030 | Wrench | 1 |
98 | 42-92-0175 | Brush Cutter Cover Head Removal Pin | 1 |
99 | 44-60-0143 | String Trimmer Guard Assembly | 1 |
104 | 43-54-0027 | 43-54-0027 | 1 |
SCREW TORQUE SPECIFICATIONS
FIG. PART NO. WHERE USED| SEAT TORQUE
(kgf-cm) (lb-in)
10| 05-74-0935| String Timmer Guard| 15-20| 15-17
23| 05-74-0015| Gear Case| 25-28| 22-24
35| 05-88-1200| Right Handle Cover| 16-20| 14-17
43| 06-82-0154| Wire Cover| 8-10| 7-9
48| 05-74-0246| Bottom Clamp Cap| 32-40| 28-35
49| 05-74-0012| Motor Mount| 11-14| 10-12
58| 06-82-1080| Motor Insulator| 8-12| 7-10
60| 06-82-0053| Stator| 2.5-3| 2-3
66| 05-88-1200| Motor Housing – Left| 19-23| 17-20
67| 05-88-1300| Lower Housing – Left| 16-20| 14-17
71| 05-74-0315| Powerhead Support| 30-40| 26-35
73| 06-82-7240| Motor Mount Assembly| 10/5/13| 9-11
76| 05-74-0238| Harness Loop| 40-50| 35-43
Route all wires as shown ensuring wires are placed completely down in wire traps. Verify all electrical components are installed firmly and squarely in housing cavities.
Route all wires as shown ensuring wires are placed completely down in wire traps. Verify all electrical components are installed firmly and squarely in housing cavities.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>