Hamworthy Stratton mk3 Retro Fit Mounting Plate Kit Instruction Manual
- June 12, 2024
- Hamworthy
Table of Contents
Hamworthy Stratton mk3 Retro Fit Mounting Plate Kit
Product Information
| Product Name | Stratton mk3 Retro-Fit Mounting Plate Kit |
|---|---|
| Compatible Boiler Models | 40, 60, 70, 40P, 60P, 70P |
| Manufacturer | Hamworthy Heating |
Product Usage Instructions
- Before commencing installation, ensure that the mounting frame/s are placed on a flat and level floor.
- Drill and fit the floor bolts (not provided) through the holes in the front of the frame feet before installing the boiler or headers.
- Isolate all flue, water, gas, and electrical services/supplies to the existing Stratton mk2 boiler.
- Use suitable lifting equipment to safely handle the weight of the boiler and remove it from the frame (Refer to Stratton mk2 Installation Manual).
- Install the retro-fit mounting plate onto the two hooks on the support frame.
- Use the provided M6 self-drilling screws to secure the mounting plate to the support frame.
- Place the Stratton mk3 boiler onto the two locating hooks on the retrofit mounting plate.
Kit Contents
| Item | Description |
|---|---|
| A | 1 x 40-70 kW Retro-Fit Mounting Plate |
| B | 1 x DN25-1 BSP Mac Union* |
| C | 2 x DN32 – 1 1/4 Gasket* |
| D | 2 x M6 Self Drilling Screw |
Supplied to assist with the boiler retro-fitting process.
IMPORTANT NOTE
THESE INSTRUCTIONS MUST BE READ AND UNDERSTOOD BEFORE INSTALLING,
COMMISSIONING, OPERATING OR SERVICING EQUIPMENT
Customer After Sales Services
- Telephone: 01202 662555
- Email: service@hamworthy-heating.com
- Fax : 01202 662522
Technical Enquiries
To supplement the detailed technical brochures, technical advice on the
application and use in the Hamworthy Heating range is available from our
technical team in Poole and our accredited agents.
Site Assembly
Hamworthy offer a service if site assembly for many of our products where
plant room access is restricted. Using our trained staff we offer a high
quality of build and assurance of a boiler built and tested by the
manufacturer.
Commissioning
Commissioning of equipment by our own engineers, accredited agents or
specialist sub-contractors will ensure the equipment is operating safely and
efficiently.
Service Contracts
Regular routine servicing of equipment by Hamworthy service engineers inspects
the safety and integrity of the plant, reducing the risk of failure and
improving performance and efficiency. Service contracts enable you to plan and
budget more efficiently.
Breakdown service, repair, replacement
Hamworthy provide a rapid response breakdown, repair or replacement service
through head office at Poole and accredited agents throughout the UK.
Spare Parts
We offer a comprehensive range if spare parts, providing replacement parts for
both current and discontinued products. Delivery options are available to suit
you. Please refer to our website hamworthy-heating.com for more details.
IMPORTANT : NOTE TO THE INSTALLER: LEAVE THESE INSTRUCTIONS ADJACENT TO THE GAS METER.
INTRODUCTION
IMPORTANT : Before commencing installation, the mounting frame/s must
stand on a flat and level floor. Before the boiler or headers are installed
drill and fit the floor bolts (not provided) through the holes in the front of
the frame feet.
The Stratton mk3 has a smaller footprint than the Stratton mk2. Therefore to
allow the Stratton mk3 to be fitted to a Stratton mk2 support frame this kit
has been provided.
This retrofit mounting plate allows boilers to be correctly positioned onto
the support frame and align with piping kits when replacing the Stratton mk2
for a Stratton mk3.
KIT CONTENTS
| Item | Description |
|---|---|
| A | 1 x 40-70 kW Retro-Fit Mounting Plate |
| B | 1 x DN25-1 BSP Mac Union* |
| C | 2 x DN32 – 1 1/4 Gasket* |
| D | 2 x M6 Self Drilling Screw |
Supplied to assist with the boiler retro-fitting process
FITTING THE RETRO-FIT MOUNTING PLATE
- Isolate all flue, water, gas and electrical services/supplies to the existing Stratton mk2 boiler.
- Remove the boiler from the frame using suitable lifting equipment to safely handle the boiler weight. (Refer to Stratton mk2 Installation Manual).
- Install the retro-fit mounting plate onto the two hooks on the support frame.
- Install the 2 x M6 self drilling screws through the 2 holes (as below) into the support frame fully tightened.
- Install the Stratton mk3 boiler onto the two locating hooks on the Retrofit mounting plate.
- Reconnect all flue, water, gas and electrical services/supplies to the Stratton mk3 boiler.
- Do all the checks as stated in the Stratton mk3 Installation Manual Commissioning section.
Hamworthy Heating Accredited Agents
Southern Ireland (Sales & Service) HEVAC Limited Naas Road, Dublin 12, Ireland
tel : 00 353 141 91919
fax : 00 353 145 84806
email : info@hevac.ie
Scotland (Sales & Service)
McDowall Modular Services
2 Penson Road, Queenslie Industrial Estate, Glasgow, G33 4AG tel: 0141 336
8795 fax: 0141 336 8954
email: MMS.McDowallModularServices@hamworthy-
heating.com
Hamworthy Heating Customer Service Centre
Sales
tel: 01202 662552
email : sales@hamworthy-heating.com
Technical Enquiries
tel : 01202 662505
email : technical@hamworthy-heating.com
Servicing
tel : 01202 662555
email : service@hamworthy-heating.com
Spares
tel: 01202 662525
email : spares@hamworthy-heating.com
British engineering excellence from Hamworthy Heating; the commercial heating
and hot water specialists.
Customer Service Centre
Hamworthy Heating Limited, Wessex House, New Fields Business Park, Stinsford
Road, Poole, Dorset, BH17 0NF
Telephone : 01202 662500
Fax : 01202 662522
Email : service@hamworthy-heating.com
Website : www.hamworthy-heating.com
Hamworthy reserves the right to make changes and improvements which may
necessitate alteration to the specification without prior notice.
References
- Hamworthy Heating commercial boilers and heating systems
- Heating.com
- Hamworthy Heating commercial boilers and heating systems
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>