Control4 C4-PS24-30 Vibrant Power Supply Installation Guide

Control4 C4-PS24-30 Vibrant Power Supply

Product Information

The Control4 Vibrant 24V Power Supply is available in different wattage options including 30W, 60W, 96W, 200W, and 300W. The 30/60/96-Watt supplies come with a low profile aluminum enclosure with knock-outs for easy installation in low-voltage applications. The 200/300-Watt supplies are encased in a sealed low profile aluminum enclosure suitable for outdoor locations. These power supplies are compatible with MLV / ELV / Incandescent TRIAC (forward phase) dimmers and can be used to power multichannel (color) control systems.

Introduction

The Control4 Vibrant 24V Power Supply dimmable drivers operate with any standard MLV / ELV / Incandescent TRIAC (forward phase) dimmers or can be used to power multichannel (color) control systems. The 30/60/96-Watt supplies are encased in a low profile aluminum enclosure that includes knock-outs for easy installation in any low-voltage application. The 200/300-Watt supplies are encased in a sealed low profile aluminum enclosure suitable for outdoor locations.

Supported models

• C4-PS24-30 – Control4 Vibrant 30 Watt 24V Power Supply
• C4-PS24-60 – Control4 Vibrant 60 Watt 24V Power Supply
• C4-PS24-96 – Control4 Vibrant 96 Watt 24V Power Supply
• C4-PSO24-200 – Control4 Vibrant 200 Watt 24V Power Supply
• C4-PSO24-300 – Control4 Vibrant 300 Watt 24V Power Supply

Specifications and supported dimming

The specifications are described below.

Warnings and considerations

• IMPORTANT! Read all installation instructions before beginning; if not qualified, do not attempt installation. Contact a qualified electrician
• IMPORTANT! To reduce the risk of fire, electric shock, or injury to persons, pay close attention to this manual and stay within its guidelines when using this product. Save these instructions for future use.
• IMPORTANT! Do not cover this product with paper surface coverings, fabrics, streamers, or other similar combustible materials.
• IMPORTANT! Do not route the cord through walls, ceilings, doors, windows, or any similar part of the building structure.
• IMPORTANT! Do not secure this product or its cord with staples, nails, or like means that may damage the outer jacket or cord insulation.
• IMPORTANT! Do not install in airtight tanks or enclosures of any kinds.
• WARNING! These products may represent a possible shock or fire hazard if improperly installed or attached in any way. Products should be installed in accordance with these instructions, current electrical codes, and/or the current National Electric Code (NEC).
• WARNING! To reduce the risk of fire, electric shock or injury to persons, make sure that the electrical power to the system is disconnected at the source prior to installation or any servicing.
• WARNING! This device must be protected by a circuit breaker (20A max).
• ATTENTION! Cet appareil doit être protégé par un disjoncteur (20A max.)
• IMPORTANT! Using this product in a manner other than outlined in this document voids your warranty. Further, Snap One is NOT liable for any damage incurred with the misuse of this product. See “Troubleshooting.”
• IMPORTANT! Snap One does not guarantee the performance of any power supply in your environment. Customer assumes all risks,including any damage to Snap One products, associated with (i) the type, load rating and quaility of the bulb and lamp/fixture, or (ii) any use or installation not in accordance with the documentation furnished by Snap One, either with the Snap One product or at www.Snapone.Com.

Before you install the power supply

Ensure that the location and intended use meet the following criteria:

• Your tape light does not exceed the maximum run length.
• Your power supply is rated for 20% more than the total wattage of the run.
• The voltage drop from the tape light length and the length of connecting wires does not go below 21.6V.

1. Before you install the power supply, calculate the length of the tape light run and multiply the length by the wattage per distance specification. For example, if you have 10 feet of Fully Tunable linear light at 6.5 W per foot, you need at least a 65-Watt power supply, that would mean you need the C4-PS24-96 – Control4 Vibrant 96-Watt 24V Power Supply.
2. Ensure that the total length of tape, wiring, and connectors does not drop the voltage below 21.6V. See this link to calculate voltage drop based on length of wires and wire gauge: ctrl4.co/vibrant-voltage drop.

Installing the power supply

1. Securely mount the power supply using the slots or screw holes on both ends of the power supply.
2. The 30W, 60W, and 96W power supplies have a wiring enclosure with line voltage and low voltage wiring compartments with knockouts that can be used to safely run your wiring. For the 200W and 300W power supplies, install your high voltage wiring inside an approved wallbox or enclosure. Ensure that all wiring complies with local electrical codes and regulations. Procedures for wiring the power supply are on the following page.

Product Usage Instructions

1. Before installing the power supply, calculate the length of the tape light run and multiply it by the wattage per distance specification to determine the required power supply. Ensure that the total length of tape, wiring, and connectors does not drop the voltage below 21.6V. You can use this link to calculate voltage drop based on wire length and gauge.
2. Securely mount the power supply using the slots or screw holes on both ends.
3. For the 30W, 60W, and 96W power supplies, use the wiring enclosure with line voltage and low voltage wiring compartments with knockouts to safely run your wiring. For the 200W and 300W power supplies, install high voltage wiring inside an approved wallbox or enclosure. Ensure that all wiring complies with local electrical codes and regulations.
4. To wire the power supply, follow the diagram below:

Connect the dimmer or switch to the 24V DC power supply as the load. Then, connect the 24V DC to the tape light. Make sure to check the polarity and connect the red wire to + and the black wire to -. Refer to the tape lighting installation guide for instructions on wiring the tape light.

Wiring the power supply

Dimmer or switch control:

• Connect the white wire (Neutral) to the corresponding terminal.
• Connect the copper wire (To ground) to the corresponding terminal.
• Connect the black wire (Line in /Hot) to the corresponding terminal.
• Connect the red wire (To Load) to the corresponding terminal.

As shown in the diagram below, connect the dimmer or switch to the 24V DC power supply as the load. Then, connect the 24V DC to the tape light. Always check the polarity and connect the red wire to + and the black wire to -. To wire the tape light, follow the instructions in the tape lighting installation guide.

Multi-channel (color) control:

Follow the same wiring instructions as for dimmer or switch control.

Ensure that you read all installation instructions before beginning and if you are not qualified, do not attempt installation. Contact a qualified electrician for assistance. It is important to pay close attention to this manual and stay within its guidelines to reduce the risk of fire, electric shock, or injury. Save these instructions for future use. Do not cover the product with paper surface coverings. If using a DMX decoder, wire the 24V DC power supply into the V+ and V- DC power input terminals on the decoder as shown below. To wire the tape light, follow the instructions in the tape lighting installation guide.

Warranty and legal information

Find details of the product’s Limited Warranty at snapone.com/legal or request a paper copy from Customer Service at 866.424.4489.
Find other legal resources, such as regulatory notices and patent information, at snapone.com/legal.

Copyright ©2022, Snap One, LLC. All rights reserved. Control4 and SnapAV and their respective logos are registered trademarks or trademarks of Wirepath Home Systems, LLC, dba “Control4” and/or dba “SnapAV” in the United States and/or other countries. 4Store, 4Sight, Control4 My Home, Snap AV, Araknis Networks, BakPak, Binary, Dragonfly, Episode, Luma, Mockupancy, Nearus, NEEO, Optiview, OvrC, Pakedge, Sense, Strong, Strong Evolve, Strong Versabox, SunBriteDS, SunBriteTV, Triad, Truvision, Visualint, WattBox, Wirepath, and Wirepath ONE are also registered trademarks or trademarks of Wirepath Home Systems, LLC. Other names and brands may be claimed as the property of their respective owners. All specifications subject to change without notice.

References

• LED Strip Light Wire Gauge & Voltage Drop Calculator | Waveform Lighting
• Policies
• Snap One

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>