BLACKplusDECKER BDH2000L, CHV1410L Cordless Hand VAC Instruction Manual

October 30, 2023
BLACKplusDECKER

BDH2000L, CHV1410L Cordless Hand VAC

Black+Decker

Cordless Hand Vac INSTRUCTION MANUAL

Catalog Numbers
BDH2000L
CHV1410L

Thank you for choosing Black+Decker!

Please read before returning this product for any reason.

If you have a question or experience a problem with your Black+Decker purchase, go to http://www.blackanddecker.com/instantanswers  If you can’t find the answer or do not have access to the Internet, call  1-800-544-6986 from 8 a.m. to 5 p.m. EST Mon. – Fri. to speak with an agent.  Please have the catalog number available when you call.

Save this manual for future reference.

To register your new product, visit www.BlackandDecker.com/NewOwner

SAFETY GUIDELINES – DEFINITIONS

It is important for you to read and understand this manual. The information it contains  relates to protecting YOUR SAFETY and PREVENTING PROBLEMS. The symbols  below are used to help you recognize this information.

DANGER: Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.

WARNING: Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.

CAUTION: Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.

NOTICE: Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may result in property damage.

IMPORTANT SAFTEY INSTRUCTIONS

When using an electrical appliances, basic precautions should always be followed, including the following: READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

WARNING: Read all safety warnings and all instructions.

Failure to follow the warnings and instructions listed below may result in electric shock, fire and/or serious injury.

WARNING:  Some household dust contains chemicals known to the

State of California to cause cancer, birth defects or other reproductive harm such as asbestos and lead in lead based paint.

WARNING: To reduce the risk of fire, electrical shock or injury:

  • Close supervision is necessary when any appliance is used by or near children. Do not allow to  be used as a toy.
  • Do not use without dust bag and/or filters in place.
  • Do not charge the unit outdoors.
  • Shock Hazard. To protect against risk of electrical shock, do not put unit or charging base in  water or other liquid.
  • Do not use dry hand vacs to pick up liquids, toxic substances, flammable or combustible liquids  such as gasoline or use in areas where they may be present.
  • Do not use wet/dry hand vacs to pick up toxic substances, flammable or combustible liquids  such as gasoline or use in areas where they may be present.
  • Do not operate in the presence of explosives and/or flammable fumes or liquids.
  • Shock Hazard. Do not operate any appliance with a damaged cord or charger or after the appliance malfunctions, is left outdoors, dropped into water or is damaged in any manner.  Return the appliance to any authorized service facility.
  • Do not use dry hand vacs outdoors or on wet surfaces.
  • Do not abuse the cord. Never carry the charger or base by the cord or yank to disconnect from an outlet; instead grasp the charger and pull to disconnect. Keep cord away from heated  surfaces. Do not pull cord around sharp edges or corners.
  • Do not allow the cord to hang over the edge of a table or counter or touch hot surfaces The unit should be placed or mounted away from sinks and hot surfaces. • Do not use an extension cord. Plug the charger directly into an electrical outlet.
  • Use the charger only in a standard electrical outlet (120V/60Hz).
  • Do not attempt to use the charger with any other product; do not attempt to charge this product with any other charger. Use only the charger supplied by the manufacturer to recharge.
  • Keep hair, loose clothing, and all parts of body away from openings and moving parts.
  • Do not insert accessories when unit is running.
  • Shock Hazard. Do not handle plug or appliance with wet hands.
  • Do not put any object into unit openings. Do not use with any openings blocked; keep free of dust, lint, hair, and anything that may reduce air flow. • Fire Hazard. Do not vacuum burning or smoking materials, such as lit cigarette butts, matches or hot ashes.
  • Do not use on or near hot surfaces.
  • Use extra caution when cleaning on stairs.
  • This appliance is intended for household use only and not for commercial or industrial use.
  • Use only as described in this manual. Use only manufacturers recommended attachments.
  • Unplug the charger from outlet before any routine cleaning or maintenance.
  • This product includes rechargeable Lithium Ion batteries. Do not incinerate batteries as they will explode at high temperatures.
  • If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for 15 minutes or until  irritation ceases. If medical attention is needed, the battery electrolyte for Lithium Ion batteries is  composed of a mixture of liquid organic carbonates and lithium salts. WARNING: Do not look into the air vents when the unit is switched on, as sometimes there  is a possibility of small debris being discharged from the air vents, especially after cleaning /  replacement of the filters as debris inside the unit can be disturbed.
  • The charger supplied with this product is intended to be plugged in such that it is correctly orientated in a vertical or floor mount position.

SAFETY WARNINGS AND INSTRUCTIONS: BATTERIES

  • Do not disassemble or open, drop (mechanical abuse), crush, bend or deform, puncture, or shred.
  • Do not modify or remanufacture, attempt to insert foreign objects into the battery, immerse or expose to water or other liquids, or expose to fire, excessive heat including soldering irons, or  put in microwave oven.
  • Only use the battery / tool with a charging system specified by the manufacturer/supplier.
  • Do not short-circuit a battery or allow metallic or conductive objects to contact both battery  terminals simultaneously.
  • Dispose of used batteries promptly according to the manufacturer/supplier’s instructions.
  • Improper battery use may result in a fire, explosion, or other hazard.
  • Battery / tool usage by children should be supervised.

SAFETY WARNINGS AND INSTRUCTIONS: CHARGING

  1. This manual contains important safety and operating instructions.
  2. Before using battery charger, read all instructions and cautionary warnings on battery charger and product using battery. CAUTION: To reduce the risk of injury, use this charger only with this  product. Batteries in other products may burst causing personal injury or damage. 
  3. Do not expose charger to rain or snow.
  4. Use of an attachment not recommended or sold by Black+Decker may result in a risk of fire,  electric shock, or injury to persons.
  5. To reduce risk of damage to electric plug and cord, pull by plug rather than cord when  disconnecting charger.
  6. Make sure cord is located so that it will not be stepped on, tripped over, or otherwise subjected  to damage or stress.
  7. An extension cord should not be used unless absolutely necessary. Use of improper extension  cord could result in a risk of fire, electric shock or electrocution.
  8. Use only the supplied charger when charging your tool. The use of any other charger could damage the tool or create a hazardous condition.
  9. Use only one charger when charging.
  10. Do not attempt to open the charger. There are no customer serviceable parts inside. Return to any authorized Black+Decker service center.
  11. DO NOT incinerate the tool or batteries even if they are severely damaged or completely worn out. The batteries can explode in a fire. Toxic fumes and materials are created when lithium ion  battery packs are burned.
  12. Do not charge or use battery in explosive atmospheres, such as in the presence of flammable  liquids, gases or dust. Inserting or removing the battery from the charger may ignite the dust or fumes.
  13. If battery contents come into contact with the skin, immediately wash area with mild soap and water. If battery liquid gets into the eye, rinse water over the open eye for three minutes or until  irritation ceases. If medical attention is needed, the battery electrolyte is composed of a mixture  of liquid organic carbonates and lithium salts.

WARNING: Burn hazard. Battery liquid may be flammable if exposed to spark or flame.

SAVE THESE INSTRUCTIONS

Symbols

• The label on your tool may include the following symbols. The symbols and their  definitions are as follows:

V……………….volts A………………..amperes
Hz……………..hertz W……………….watts
min……………minutes or AC……..alternating current
or DC…direct current no………………no load speed
……………..Class I Construction ………………earthing terminal
(grounded) ………………safety alert symbol
……………..Class II Construction …/min or rpm..revolutions or reciprocation
(double insulated) per minute

Product Features

  1. On/off switch
  2. Bowl release button
  3. Charging indicator
  4. Dust bowl
  5. Nozzle
  6. Nozzle release button
  7. Nozzle rotating button
  8. Extendable crevice tool
  9. Flip-up Brush
  10. Charger base
  11. Charge
  12. Cloth filter
  13. Plastic pre-filter

Charging the battery

• Place the appliance on the charging base as shown.

• Plug in the charger. The charging indicator will flash  continuously (slowly).

• Leave the appliance to charge.

While charging, the charger may get warm, this is  perfectly normal and safe. The charging indicator will be  lit as long as the appliance is connected to the plugged in charger. It can remain on charge indefinitely without  damage or danger. It is not possible to “overcharge” the  battery cells with the charger provided.

WARNING: Do not charge the battery at ambient temperatures below 39°F (4°C) or above 104°F (40°C). The charge is complete when the charging indicator lights continuously. The charger  and the battery can be left connected indefinitely with the LED illuminated. The LED will  change to flashing (charging) state as the charger occasionally tops off the battery charge.

  • Charge discharged batteries within 1 week. Battery life will be greatly diminished if  stored in a discharged state.

Battery diagnostics

If the appliance detects a weak battery, the charging indicator will flash at a fast rate.  Proceed as follows:

  • Place the appliance on the charging base.
  • Plug in the charger.
  • Leave the appliance to charge.

If the appliance detects a damaged battery, the charging indicator will flash at a fast  rate when the appliance is on the charger base. Proceed as follows:

• Take the appliance and the charger to be tested at an authorized service facility.

Note: It may take as long as 60 minutes to determine that the battery is defective.  If the battery is too hot or too cold, the LED will alternately blink, fast and slow,  one flash at each speed and repeat.

Use

Switching on and off

  • Figure B – To start, slide the On/Off switch  forward (i.e. “O”= Off, “I” = On). 
  • To stop, slide the switch back.
  • Return the product to the charger immediately  after use so that it will be ready and fully charged  for the next use. Ensure that the product is fully  engaged with the charger base.

Cleaning and emptying the product

WARNING:  Projectile/Respiratory Hazard: Never use the vac  without its filter.

NOTE:  The filter is re-usable, do not confuse it with a disposable dust bag, and do not  throw it away when the product is emptied. We recommend that you replace the filter  every 6-9 months depending on frequency of use.

There are two methods of cleaning the bowl, a quick empty method and a thorough  clean method.

For a quick empty (figures C,D)

  • Figure C – Press in on both nozzle release  buttons on the sides of the nozzle and remove the  nozzle by pulling straight off.
  • Figure D – Empty the dust from the bowl.
  • For a more thorough cleaning, remove bowl as  described in figures E, F, & G.

Removing the dust bowl and filters (figures E – H)

WARNING: The filters are re-usable and should be cleaned regularly.

  • Press the release latch and pull the dust bowl  straight off.
  • While holding the dust bowl over a bin or sink,  pull out the filter to empty the contents of the  bowl.
  • To replace the dust bowl, place it back onto the  handle until it “clicks” firmly into position.

WARNING: Never use the appliance without the filters. Optimum dust collection will only be achieved with clean filters.

• Figure F – This vacuum has a plastic pre-filter  and an inner cloth filter. To separate the cloth  filter from the plastic filter, twist the plastic filter in a  clockwise direction.

• Remove the inner cloth filter and shake or lightly  brush any loose dust off both filters.

• Figure G – The dust bowls and filters can be washed in warm soapy water. Allow to dry  before placing back into the vac.

• Figure H To replace the filters, slide the outer plastic filter over  the cloth filter.

• Align the wings of the plastic filter with the slots in the cloth  filter and twist in a counterclockwise direction.

• Place filters back into the bowl pressing firmly to ensure a  secure fit.

• To replace dust bowl, place it back onto the handle until it  “clicks” firmly into position.

IMPORTANT:  Maximum dust collection will only be obtained  with a clean filter and an empty dust bowl. If dust begins to fall  back out of the product after it is switched off, this indicates that  the bowl is full and requires emptying.

• Wash the filters regularly using warm, soapy water and ensure  that they are completely dry before using again. The cleaner the  filter is, the better the product will perform.

• It is very important that the filter is correctly in position before  use.

Nozzle / Accessories

• Figure I – A crevice tool is built into the nozzle  and can be extended as shown in figure H by  pulling the extension piece until it locks into position.

• Figure J – A brush accessory is built into the  nozzle and can be flipped upwards for use.

• Figure K – The nozzle can be rotated for better  access in tight spots. To rotate the nozzle, press  the button shown in figure K and rotate the nozzle to the left or right until it clicks into place.

Replacing the filters

The filters should be replaced every 6 to 9 months and whenever worn or damaged.  Replacement filters are available from your Black+Decker dealer. Visit www.blackanddecker.com to locate dealers.

• Remove the old filters as described above.

• Fit the new filters as described above.

Maintenance

Bowls and filters can be washed thoroughly; however, use only mild soap and a damp  cloth to clean the main part of the vacuum.

IMPORTANT: To assure product SAFETY and RELIABILITY, repairs, maintenance and adjustment (other than those listed in this manual) should be performed by authorized  service centers or other qualified service personnel, always using identical replacement  parts.

Troubleshooting

If the product does not work, check the following:

  • The charge indicator light is flashing when unit is connected to charger.
  • The charger was correctly plugged in for recharge. (It feels slightly warm to the touch.)
  • The charger cord is not damaged and is correctly attached.
  • The charger is plugged into a working electrical outlet.
  • The switch is in the “OFF” position when charging.

For assistance with your product, visit our website www.blackanddecker.com for the  location of the service center nearest you or call the Black+Decker help line at  1-800-544-6986.

Accessories

Recommended accessories for use with your product are available from your local dealer  or authorized service center. If you need assistance regarding accessories, please call:  1-800-544-6986.

  • Filter accessory number VF110.

WARNING: The use of any accessory not recommended for use  with this product could be hazardous.

Battery Removal and Disposal

This product uses Lithium Ion rechargeable and recyclable batteries. When the batteries no longer hold a charge, they should be removed from the Vac and recycled.  They must not be incinerated or composted.

The batteries can be taken for disposal to a Black+Decker, Company-Owned or Authorized Service Center. Some local retailers are also participating in a national  TM recycling program (see “RBRC Seal”). Call your local retailer for details. If you bring the batteries to a Black+Decker Company-Owned or Authorized Service Center,  the Center will arrange to recycle old batteries. Or, contact your local municipality for  proper disposal instructions in your city/town.

To remove the battery pack for disposal:

  1. First, before attempting to disassemble the product, turn it on and leave it on until  the motor completely stops insuring a complete discharge of the batteries.
  2. Using a phillips screwdriver, remove the seven screws securing the two housing  halves.
  3. Lift the housing cover away from the assembly.
  4. Detach all lead connections from battery pack.
  5. Remove battery pack and dispose of as per recommended guidelines.

The RBRC™ Seal

The RBRC™ (Rechargeable Battery Recycling Corporation)

Seal on the Lithium Ion battery (or battery pack) indicates that the costs to recycle  the battery (or battery pack) at the end of its useful life have already been paid by  Black+Decker. In some areas, it is illegal to place spent Lithium Ion  batteries in the trash or municipal solid waste stream and the RBRC program  provides an environmentally conscious alternative.

RBRC in cooperation with Black+Decker and other battery users, has established programs in the United States and Canada to facilitate the collection of spent Lithium Ion batteries. Help protect our environment and conserve  natural resources by returning the spent Lithium Ion battery to an authorized  Black+Decker service center or to your local retailer for recycling. You may also  contact your local recycling center for information on where to drop off the spent battery,  or call 1-800-8-BATTERY.

Service Information

All Black+Decker Service Centers are staffed with trained personnel to provide customers with efficient and reliable power tool service. Whether you need technical  advice, repair, or genuine factory replacement parts, contact the Black+Decker location nearest you. To find your local service location, call: 1-800-544-6986 or visit  www.blackanddecker.com

Limited Two-Year Home Use Warranty

Black & Decker (U.S.) Inc. warrants this product to be free from defects in material or  workmanship for a period of two (2) years following the date of purchase, provided that the  product is used in a home environment. This limited warranty does not cover failures due to  abuse, accidental damage or when repairs have been made or attempted by anyone other  than Black+Decker and its Authorized Service Centers. A defective product meeting the  guarantee conditions set forth herein will be replaced or repaired at no charge in either of two  ways:

The first, which will result in exchanges only, is to return the product to the retailer from  whom it was purchased (provided that the store is a participating retailer). Returns  should be made within the time period of the retailer’s policy for exchanges. Proof of  purchase may be required. Please check with the retailer for its specific return policy  regarding time limits for returns or exchanges. The second option is to take or send  the product (prepaid) to a Black+Decker owned or authorized Service Center for  repair or replacement at Black+Decker’s option. Proof of purchase may be required.

Black+Decker owned and authorized service centers are listed online at www.blackanddecker.com.

This warranty does not apply to accessories. This warranty gives you specific legal  rights and you may have other rights which vary from state to state. Should you have  any questions, contact the manager of your nearest Black+Decker Service Center.  This product is not intended for commercial use, and accordingly, such commercial use  of this product will void this warranty. All other warranties, express or implied, are hereby  disclaimed.

LATIN AMERICA: This warranty does not apply to products sold in Latin America. For  products sold in Latin America, check country specific warranty information contained in  the packaging, call the local company or see the website for such information. free warning label replacement: If your warning labels become illegible or  are missing, call 1-800-544-6986 for a free replacement.

Imported by

Black & Decker (U.S.) Inc.,

701 E. Joppa Rd.

Towson, MD 21286 U.S.A.

References

Read User Manual Online (PDF format)

Loading......

Download This Manual (PDF format)

Download this manual  >>

Related Manuals