BLACKSTONE 1832 17 Inch Griddle Owner’s Manual
- June 12, 2024
- BlackStone
Table of Contents
- BLACKSTONE 1832 17 Inch Griddle
- Product Information
- Product Usage Instructions
- IMPORTANT SAFETY INFORMATION
- ACTIVATE YOUR WARRANTY
- ASSEMBLY GUIDE
- USING YOUR BLACKSTONE
- Griddle Seasoning Instructions
- Cooking on Your Blackstone
- TROUBLESHOOTING
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
BLACKSTONE 1832 17 Inch Griddle
Product Information
- Model: 1832 v15
- Manufacturer: North Atlantic Imports LLC
- Warranty: 1-Year Warranty
- Product Usage: Griddle
Product Usage Instructions
- Read and follow all warnings and instructions in the user manual before assembling and using the appliance.
- Make sure the installation of the appliance conforms with local codes. In the absence of local codes, refer to the National Fuel Gas Code, ANSI Z223.1/NFPA 54, Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58; or Natural Gas and Propane Installation Code, CSA B149.1; Propane Storage and Handling, CSA B149.2; or The Standard for Recreational Vehicles, ANSI A119.2/NFPA 1192; and Recreational Vehicle Code, CSA Z240 RV Series, as applicable.
- Activate your warranty by providing your appliance’s serial number when registering.
- The warranty covers replacement parts up to one year after the date of purchase.
- The appliance should be operated exclusively for domestic use and not for private or public club, institutional, or commercial purposes.
- For any defects in material and workmanship under normal use and service, contact North Atlantic Imports LLC for free replacement or repair of the defective part(s) within the specified periods of time from the date of purchase.
Note: For more detailed information and support, please visit BlackstoneProducts.com/support.
IMPORTANT:
This instruction manual contains important information necessary for the
proper assembly and safe use of the appliance.
Read and follow all warnings and instructions before assembling and using the
appliance.
Follow all warnings and instructions when using the appliance.
Keep this manual for future reference.
Installer/Assembler: Leave these instructions with the consumer.
SAFETY ALERT KEY
danger
Indicates a hazardous situation that, if not avoided, will result in death or
serious injury.
Caution
Indicates a hazardous situation that, if not avoided, could result in minor or
moderate injury.
WARNING
Indicates a hazardous situation that, if not avoided, could result in death or
serious injury.
NOTICE
Indicates information considered important, but not hazard-related (e.g.
messages related to property damage).
IMPORTANT SAFETY INFORMATION
DANGER
If you smell gas:
- Shut off gas to the appliance.
- extinguish any open flame.
- open hood.
- If odor continues, keep away from the appliance and immediately call your gas supplier or your fire department.
Failure to follow these instructions could result in fire or property damage, personal injury or death.
danger
- Never operate this appliance unattended.
- Nevers operate this appliance within 10 ft (3.0 m) of any structure, combustible material or other gas cylinder.
- Never operate this appliance within 25 ft (7.5 m) of any flammable liquid.
- If a fire should occur, keep away from the appliance and immediately call your fire department. do NoT attempt to extinguish an oil or a grease fire with water.
Failure to follow these instructions could result in fire or property damage, personal injury or death.
WARNING
- do Knot store or use gasoline or other flammable liquids or vapors in the vicinity of this or any other appliance.
- An lPG cylinder not connected for use shall not be stored in the vicinity of this or any other appliance.
GAS APPLIANCE SAFETY
- The use of alcohol, prescription, or non-prescription drugs may impair the consumer’s ability to properly assemble or safely operate the appliance?
- Keep children and pets away from the appliance at all times
- Have a type BC or ABC fire extinguisher readily available
DO NOT USE FOR PURPOSES OTHER THAN INTENDED:
- do Not use for commercial cooking
- do Not use this appliance as a heater
THIS APPLIANCE SHALL BE USED OUTDOORS ONLY.
- do Not use this appliance inside buildings, garages, or any other enclosed area
- do Not install this appliance in or on a boat
- do Not install this appliance in or on a recreational vehicle
MAINTAIN PROPER CLEARANCES FROM COMBUSTIBLE MATERIAL:
- do Not use this appliance on or under any apartment or condo-minimum balcony or deck
- do Not use this appliance under overhead combustible construction
- do Not obstruct the flow of combustion and ventilation air
- do Not operate this appliance any closer than 36 in (1 m) from the sides and back of the appliance
INSTALLATION MUST CONFORM WITH LOCAL CODES
In the absence of local codes, installation must conform with:
- National Fuel Gas Code, ANSI Z223?1/NFPA 54, Storage and Handling of Liquefied Petroleum Gases, ANSI/NFPA 58; or
- Natural Gas and Propane Installation Code, CSA B149?1; Propane Storage and Handling, CSA B149?2; or
- The Standard for Recreational Vehicles, ANSI A119?2/NFPA 1192; and Recreational Vehicle Code, CSA Z240 RV Series, as applicable
ACTIVATE YOUR WARRANTY
The North Atlantic Imports llC 1-Year Warranty covers replacement parts up to one year after the date of purchase
TO ENABLE THIS WARRANTY, YOU WILL NEED TO PROVIDE:
Your appliance’s Serial Number
The Serial Number can be found on your appliance’s Manufacturer label
Register your appliance at BlackstoneProducts.com/register
WARRANTY OVERVIEW
North Atlantic Imports, the manufacturer, will warranty for one year from
purchase all parts, workmanship, and finishes It will be the manufacturer’s
option as to whether to repair or replace any of the above items All
warranties are limited to the original purchaser only
This warranty does not cover any liability on the part of North Atlantic
Imports, its agents or employees, for any indirect or consequential damages
for breach of warranty
The purchaser must follow the manufacturer’s usage instructions
Under no circumstances is the manufacturer responsible for damages from the
failure to operate the cooking station properly
It is the responsibility of the purchaser to establish the warranty period by
verifying the original purchase date with original sales receipt
DETAILED Explanation OF THE WARRANTY
North Atlantic Imports llC warrants to the owner that the product covered by
this agreement is free from defects in material and work- stated periods of
time from the date of purchase; for one year from purchase, all parts, finish,
and workmanship. Should any failure to conform to this warranty become
apparent during applicable warranty periods stated above, the original
purchaser must notify North Atlantic Imports llC of breach of warranty within
the applicable warranty period.
North Atlantic Imports llC shall upon notice and compliance by the original
purchaser with such instructions, correct such nonconformity by repair or
replacement of the defective part or parts. Correction in the manner provided
above shall constitute a fulfillment of all obligations of North Atlantic
Imports llC with respect to the quality of the product.
North Atlantic Imports llC does not warrant this equipment to meet the
requirement of any safety code of any state, municipality or other
jurisdiction, and the original purchaser assumes all risk and liability
whatsoever resulting from the use thereof, whether used in accordance with
North Atlantic Imports llC instructions or otherwise.
This warranty does not cover and is intended to exclude any liability on the
part of North Atlantic its agents, servants or employees whether under this
warranty or implied by law for any indirect or consequential damages for
breach on any warranty. The purchaser must establish all applicable warranty
periods pursuant to this warranty by verifying the original purchase date by
producing the dated sales receipt. This warranty shall not apply to this
product or any other part thereof which has been subject to accident,
negligence, alteration, abuse, or misuse or which has been repaired or altered
without North Atlantic written consent, outside of North Atlantic Imports llC
factory. The full manufacturer warranty is
not valid for griddles purchased from unlicensed, third-party resellers,
purchased at a discount due to missing or damaged parts, or purchased as a
floor model; at the discretion of North Atlantic Imports.
North Atlantic Imports llC makes no warranty whatsoever in respect to
accessories or parts not supplied with it. This warranty shall apply only
within the boundaries of the United States of America and Canada. This
warranty gives the original purchaser specific rights, and the original
purchaser may also have other rights, which vary from state to state.
ASSEMBLY GUIDE
Exploded View
Parts List
Parts : Qty
- 1.1a Front panel 1
- 1.1b Knob bezel 1
- 1.2 Back panel 1
- 1.3a Bottom panel 1
- 1.3b Hat channels 2
- 1.4 Right panel 1
- 1.5 Left panel 1
- 1.6 Front baffle panel 1
- 1.7 Gas rail 1
- 1.8 H burner 1
- 1.9 Ignition needle 1
Assembly **Instructions**
Find a large, clean area to assemble your appliance. Remove all packing
material before assembling.
Caution
Sharp edges. Wear gloves while assembling.
- Step 01
Remove the griddle body from the packaging. Take the griddle top off and set aside. Place griddle on a smooth flat surface. Install the control knob by pushing it into place in the OFF position.
-
STEP 02
Ensure that the fuel nozzle is housed within the burner opening -
STEP 03
Use four (4) M8 flange nuts to attach four (4) griddle feet to the bottom of the griddle?
- STEP 04
Set the griddle on its feet? ensure that the ignition needle is set 3-7mm above the burner tube?
-
Step 05
Place the griddle top on the griddle body. Make sure the four positioning pegs on the griddle top are seated into the griddle body. -
Step 06
Assemble the grease cup. Hang the grease cup on the rear of the griddle top.
-
Step 07
Proceed to USING YOUR BLACKSTONE.
NOTICE
Place appliance on a heat-resistant and flame-resistant surface while in use.
USING YOUR BLACKSTONE
CONNECT THE LPG CYLINDER 1 LB (453 G)
- STEP 01
Screw in the lPG cylinder into the gas regulator, turning the cylinder clockwise. The regulator may make a humming or whistling noise during operation. This
will not affect safety or use of the appliance.
REGULATOR SAFETY
WARNING
Cross threading can occur if you force thread a connection at an improper
angle. This will damage the threads, lead to propane leaking, and potentially
result in a build-up of fuel that can ignite.
DO NOT cross thread the connection between your LPG cylinder and regulator or
regulator and gas rail.
WARNING
If you can not connect the regulator, DO NOT use the regulator.
Regulator must be replaced with a Blackstone approved model by a
professionally licensed, authorized dealer.
Use this appliance, as purchased, only with gas and regulator/valve assembly
supplied.
If regulator f fails in unit, it must be replaced with a Blackstone approved
model (found on your Manufacturer label) by a professionally licensed,
authorized dealer. Failure to comply will void the warranty.
- STEP 02
Insert the regulator and lPG cylinder into the gas line of the appliance. Turn the collar of the regulator clockwise to secure it to the gas line.
LEAK TEST INSTRUCTIONS NOTICE
DO NOT use household cleaning agents. Damage to gas valve and regulator
components may result. Use a clean paintbrush and a 10/90 mild soap and water
solution to perform the leak test.
-
STEP 01
Turn the control knobs to oFF. -
STEP 02
Connect the lPG cylinder to the regulator. Connect the regulator to the appliance.
The regulator may make a humming or whistling noise during operation. This will not affect safety or use of the appliance.
IF FROSTING PERSISTS AFTER BOTTLE IS ANGLED CORRECTLY:
-
STEP 01
Turn off the appliance and disconnect lPG cylinder immediately.
This indicates a problem with the lPG cylinder and it should not be used on any product. -
STEP 02
Return lPG cylinder to supplier. -
STEP 03
Brush soapy solution onto joint areas of valves and regulator. leaks are indicated by growing bubbles.
STEP 04
If growing bubbles appear, re-tighten connections.
WARNING
- If leaks cannot be stopped, DO NOT try to repair.
- Regulator must be replaced with a Blackstone approved model.
FIRST Timed Cleaning
CLEANING YOUR GRIDDLE TOP
NOTICE
Soap will ruin a seasoned griddle. This is the only time you should use soap
on the griddle cooking surface.
-
STEP 01
Wash the griddle cooking surface with hot, soapy water. -
STEP 02
Rinse and dry completely.
Ignition Instructions
CHECK VALVES
- STEP 01 Turn knob to of position.
- STEP 02 Push in knob and release. Knob should spring back. If knobs do Not spring back, replace valve assembly before using appliance.
- STEP 03 Rotate knob to low then turn back to off. Knob should turn smoothly.
PIEZO-ELECTRIC GRIDDLE IGNITION
- do not lean over the appliance while lighting
- Push the control knob in to start gas flowing.
- Turn the control knob counter-clockwise to activate the starter.
- Adjust the temperature to desired level.
CHECK BURNER FLAME
Always check burner flame before use.
-
STEP 01
light burners and rotate knobs from HIGH to loW. -
STEP 02
look below the cooking top to view burners. When knob is at HIGH, flames should be larger than when knob is at loW
WARNING
A clogged burner can lead to a fire beneath the appliance.
Burner should be removed and cleaned annually or whenever heavy build-up or
insects/insect nests are found.
HEALTHY BURNER FLAME
PATTERN
- Flickers of yellow color.
- dark blue color.
- Vibrant blue
BURNER FLAMES ARE YELLOW OR IRREGULAR
If there is a sudden drop or low flame issue, please reference the Troubleshooting chapter.
Griddle Seasoning Instructions
WHAT OIL IS BEST TO USE?
- Blackstone Seasoning and Cast Iron Conditioner.
- Any plant-based cooking oil.
- Rendered animal fat with no additives.
VIDEO TUTORIAL
How to Season a New Blackstone Griddle
youtube.com/watch?v=VspmdVnj2pI&t=3s
-
STEP 01
Wipe any debris off griddle top -
STEP 02
Set your griddle to high heat until your griddle top changes color. (~10 min) -
STEP 03
Use tongs to hold a paper towel or cotton cloth and spread 2-3 tablespoons of your seasoning oil across the entire griddle top. When seasoning your griddle top, remember to use a thin and even layer of oil—the thinner the layer of oil, the easier it will be to burn it offff. -
STEP 04
The griddle top is ready for another layer of oil when it stops smoking. Repeat STEP 03 3-4 times, or until the griddle surface is black.
SEASONING TROUBLESHOOTING
THERE IS A BROWNISH RESIDUE ON THE GRIDDLE SURFACE:
POSSIBLE : CAUSES SOLUTION
-
Too much oil was used.
-
You turned off the heat too soon.
-
STEP 01
Turn your griddle on high and let it heat for 10-15 minutes. -
STEP 02
Scrape off as much of the thickened and partially cooked oil as you can. -
STEP 03
Re-season with a very thin layer of oil.
-
THE EDGES OF THE GRIDDLE SURFACE ARE NOT BLACK:
After using your griddle for multiple cooks, the seasoning will even out and
improve.
PREVENTING RUST
Use your griddle frequently. every time you cook, you are adding to the
seasoning, which makes rust less likely.
NOTICE
If you live in a humid or coastal climate, your griddle may require more
frequent seasonings between uses. If rust appears on the griddle surface, rub
it off with steel wool, low grit sandpaper or the Blackstone Pumice Stone and
re-season the surface.
VIDEO TUTORIAL
Recovering your Blackstone Griddle Top
youtube.com/watch?v=thPe2IgnSiI
Cooking on Your Blackstone
danger
Flammable items can spontaneously combust if placed near the appliance. DO NOT
place flammable items such as aerosol containers, oily or greasy towels near
the cooking surface.
Caution
This appliance will be hot during and after use. DO NOT handle hot parts with
unprotected hands. Use long-handled cooking utensils and oven mitts.
NOTICE
DO NOT store any items within 3 in (8 cm) of the cooking surface while in use.
GREASE OR OTHER HOT MATERIAL DRIPS ONTO VALVE, HOSE OR REGULATOR:
- STEP 01 Turn off gas supply immediately.
- STEP 02 determine the cause and correct it.
- STEP 03 Clean and inspect valve, hose and regulator.
- STEP 04 Perform a leak test. (Please reference the leak Test Instructions in USING YOUR BLACKSTONE.) VIDEO RECIPES
Find recipes and cooking tips at:
- BlackstoneProducts.com/blogs/recipes
- youtube.com/c/BlackstoneGriddles
- @blackstoneproducts
Cleaning Your Appliance
Clean your appliance after each use, after it is cool to the touch.
- do Knot use abrasive pad on areas with graphics.
- If a bristle brush is used to clean any of the cooking surfaces, ensure no loose bristles remain on cooking surfaces prior to cooking.
WARNING
Grease build up can cause a fire. Clean any part of the appliance that gets
hot and experiences grease build up after each use.
PLASTIC PARTS & PAINTED SURFACES:
Wash with warm soapy water and wipe dry with a non-abrasive cloth.
NOTICE
DO NOT use Cortisol, abrasive cleaners, or a concentrated cleaner on plastic
parts. This may result in damage to and failure of parts.
FOR EVERY SURFACE
The Blackstone degreaser and Cleaning Spray is gentle enough to clean every
surface of your appliance. Use it on the cooking surface, the appliance frame,
or anywhere that experiences a build up of grease
APPLIANCE STORAGE
WARNING
DO NOT move the appliance when in use. Allow the appliance to cool to 115°F
(45°C) before moving or storing.
COVER FIT GUIDE
Always cover your appliance when stored outdoors.
To find a cover that will fit your appliance, visit
BlackstoneProducts.com/support
CLEANING YOUR GRIDDLE TOP
Clean griddle top after each use, while still warm.
- do Not use soap on the griddle top. This will destroy the griddle’s seasoning.
- The grease cup must be removed and emptied after each use.
CAUTION
Grease cup will be hot during and after use. DO NOT remove the grease cup
until the griddle has completely cooled.
VIDEO TUTORIAL
How to Clean your Blackstone Griddle
youtube.com/watch?v=-Iedu9z6NPY
-
STEP 01
Push loose food debris into the grease cup with spatula or straight metal scraper. -
STEP 02
Wipe down griddle top with paper towel. -
STEP 03
Apply a few tablespoons of water to the griddle surface, then scrape the water and debris into the grease cup. (For stuck-on food residue, use a bit of coarse salt.) -
STEP 04
Wipe again with a paper towel and dry completely. -
STEP 05
Apply thin coat of cooking oil to maintain seasoning and protect the griddle top disconnect
disconnect The lPG Cylinder
1 LB (453 G)
-
STEP 01
-
ensure that the control knob(s) are turned to oFF.
-
STEP 02
once the appliance has cooled, disconnect the regulator from the gas line by unscrewing the collar. -
STEP 03
Unscrew the lPG cylinder from the regulator. -
STEP 04
Place dust cap on lPG cylinder valve outlet whenever cylinder is not in use. only install the type of dust cap on cylinder valve outlet that is provided with the cylinder valve. other types of caps or plugs may result in leakage of propane.
STORING LPG CYLINDERS
WARNING
- DO NOT store a spare LPG cylinder under or near this appliance.
- DO NOT fill an LPG cylinder beyond 80% full. If the information above is not followed exactly, a fire causing death or serious injury may occur.
- The lPG cylinder must be disconnected when the appliance is not in use.
- only store the appliance indoors if the lPG cylinder is disconnected and removed from the appliance
TROUBLESHOOTING
IGNITION TROUBLESHOOTING
BURNER WILL NOT IGNITE:
If ignition does not occur in 5 seconds:
-
STEP 01
Turn the burner control knob oFF. -
STEP 02
Wait 5 minutes. -
STEP 03
Repeat the lighting procedure.
If this does not work, to determine the cause, please try to ignite your appliance with a match.
MATCH LIGHTING INSTRUCTIONS
Before beginning, check for gas leaks. open hood (if applicable).
-
STEP 01
Turn control knob to oFF position -
STEP 02
light a match (or long lighter) no shorter than 11 inches long. -
STEP 03
Place the flame next to burner. -
STEP 04
Push in and turn the control knob to start gas flowing. ensure burner lights and stays lit.
IF YOU CAN IGNITE YOUR APPLIANCE WITH A MATCH:
POSSIBLE CAUSES : SOLUTION
- Ignitor wire misaligned
- ensure that the ignition needle is positioned 3-7mm away from the burner tube, and above a burner hole.
- damage to the ignition system.
- Contact customer service for replacement parts.
GAS FLOW TROUBLESHOOTING
BURNER FLAMES ARE YELLOW OR IRREGULAR:
- Appliance will not achieve a high heat or heats unevenly.
- Burner flames start strong, then immediately drop to low even when burner is set to high position.
- Flame height drops when a second burner is lit.
- Flames do NoT extend the full length of the burner, or only run on one side of the burner.
- Burner flames are inconsistent.
POSSIBLE CAUSES : SOLUTION
-
obstructions in the burner, gas jets, or fuel rail.
- Clean the burner, jets, and gas hose.
-
lPG cylinder is empty or low. Refill or replace the lPG cylinder.
- The regulator’s flow limiting device was triggered.
-
Reset the safety system:
-
STEP 01
Turn oFF the appliance, close the lPG cylinder valve, and disconnect the regulator from the lPG cylinder. -
STEP 02
Wait five minutes toallow the pressure to dissipate, then reconnect the regulator to the lPG cylinder and slowly open the oPd hand wheel one half turn. -
STEP 03
-
Ignite your appliance.
-
-
Regulator stuck in safety position.
- Contact customer service for replacement parts
A FLAME IS COMING OUT OF THE AIR GATE:
POSSIBLE CAUSES: SOLUTION
- Something is blocking the venture in the burner.
- Clean the burner assembly to remove the obstruction.
CLEANING THE BURNER ASSEMBLY
VIDEO TUTORIAL
How to Clean Your Burner Tube
youtube.com/watch?v=xKQTCrFCzf8
-
STEP 01
ensure that the gas is turned oFF at control knobs and gas supply. Remove the cooking top. -
STEP 02
Carefully detach and remove the burner. -
STEP 03
Clean the inside of the burner:- Run a narrow bottle brush through each burner tube several times. (do NoT use wire brushes)
- Run a stiff wire bent into a small hook through each burner tube several times.
- Use compressed air to blow through the burner tube and out the burner ports. Check that air blows through each hole. (Wear eye protection)
-
STEP 04
Brush entire outer surface of burner to remove grime. -
STEP 05
Clean any blocked ports with stiff wire such as an open paper clip. -
STEP 06
Carefully replace burners and reattach.- The gas rail fuel nozzle must be reengaged within the burner opening
CUSTOMER SERVICE
Visit us online at
blackstoneproducts.com/support for
assistance concerning appliance use, replacement parts, or your warranty.
CUSTOMER SERVICE HOURS:
Monday – Friday 7:00 am – 5:00 pm (MST)
This product may be covered by one or more issued U.S. and/or international
patents and may include patent applications pending.
For more information, please visit:
BlackstoneProducts.com/patents
distributed BY Norths Atlantic Imports, llC 1073 W 1700 N Logan, UT 84321 USA
| Blackstone IS A Registered Trademark of Norths Atlantic Imports, ll
©2022 Norths A 20 Atlantic Imports. All RIGHTS Reserved.
References
- Blackstone Recipes – Blackstone Products
- Register Product - Blackstone Products
- Support – Blackstone Products
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>