BRIZO 61374LF-C-GL RO/Cold Water Dispenser Instruction Manual

61374LF-C-GL RO/Cold Water Dispenser
Instruction Manual

61374LF-C-GL RO/Cold Water Dispenser

Model Number: __
Date of Purchase: _____
To find model number, look on the water line label underneath sink.
Register Online
www.brizo.com/customer-support/product-registration
To reference replacement parts and access technical documents, product info, and cleaning and care instructions, visit www.brizo.com
This model is supplied with an air gap designed to accommodate most reverse osmosis drain systems, if required by state or local codes.Read all instructions prior to installation.
CAUTION
Failure to read these instructions prior to installation may result in personal injury, property damage, or product failure. Manufacturer assumes no responsibility for product failure due to improper installation.
1-877-345-BRIZO (2749)
www.brizo.com/customer-support

This product can be used in three ways. Follow instruction as shown for your specific use.

• Reverse Osmosis System
• Cold Water Tap
• Filtered Water Device

You may need:
Usted puede necesitar:
Articles dont vous pouvez avoir besoin:

112897 REV B 11/30/2022

• Slide gasket onto the tubes with paper backing oriented up.
• Remove paper backing to expose adhesive and install gasket.
• Insert faucet into sink, ensuring it is centered in the hole.

• Install mounting hardware with supplied wrench until snug.
• Adjust final position of faucet above sink if necessary.
• Tighten hardware (method 2A or 2B depending on model) until faucet resists movement, being careful not to overtighten.

NOTICE
To avoid risk of property damage, follow instructions for proper installation.
Failure to follow these instructions may result in risk of property damage caused by leaking at this connection.
Do not use pipe dope or other sealants on water line connections.
Maximum tube bend is 8”.
Faucet fittings are 3/8” compression. If  fittings are used, ensure fittings and end connections are free of debris. turn nut by hand until it feels snug, then tighten nut at least 2 more turns with a wrench. Drain Line:

• Route the black drain line from the faucet air gap to the drain so that it slopes continuously downward without any loops or low spots.
• Cut tubing to the proper length if necessary, referring to the ‘Custom Fit Connection’ section, and connect it to the drain saddle elbow.

Supply Line:

• Connect supply line with a short and direct connection between the RO system and the faucet.
• A 3/8” x ¼” union (not included) may be required depending on the RO system used.

RO Waste Line:

• Route the red RO Waste line from the RO system to the faucet in a direct connection, without any loops or low spots.

Drain and Waste Lines:
– Coil and secure both lines out of the way as they are not used for this installation. Or if you never plan on using the RO system, you may cut both tubes.
Supply Line:

• Use the inlet tubing and 1/4” compression fitting to connect directly to the cold water supply stop.
• If a cut is required, refer to the ‘Custom Fit Connection’ section and use a PLASTICferrule or direct connection system for 1/4” O.D. pex tubing.

Drain and Waste Lines:

• Coil and secure both lines out of the way as they are not used for this installation. Or if you never plan on using the RO system, you may cut both tubes.

Supply Line:

• Connect the inlet fitting to the filter system using the method prescribed by the filter manufacturer. A coupling may be required to connect the 1/4” supply line on the faucet to the filter.
• If a cut is required, refer to the ‘Custom Fit Connection’ section and use a PLASTIC ferrule or direct connection system for 1/4” O.D. pex tubing.

• Remove aerator and flush system for a minimum of 5 gallons (19 liters).
• Reinstall aerator and tighten.
• Check all connection points for leaks.

CUSTOM FIT CONNECTIONS

NOTICE

If you determine the PEX supply tubing for this faucet is too long and must be shorter to create an acceptable installation, be sure to read these instructions and plan ahead. When cutting the supply tubing, the installer accepts the responsibility to do so in a way that allows a leak-free joint to be created. Manufacturer is not responsible for tubing that is cut too short or cut in a way that will not allow for a leak-free joint. DO NOT use a metal sleeve (ferrule) or gasket (supplied with faucet) in place of the plastic sleeve (ferrule) supplied because it may not create a leak-free joint. Do not use pipe dope or other sealants on water line connections.
For custom fit installations, you must use plastic sleeves (ferrules) supplied with model and nuts included on supply lines. Do not use gasket supplied with PEX tubing or brass ferrule supplied with valve stops. Tube cut must be straight and burr free.
Failure to use plastic sleeve (ferrule) in the correct orientation will result in disconnection and possible water damage.

• Determine desired length of supply tube, leaving 1″- 2″ of extra length to allow for easier installation.
• Cut tube, ensuring it is cut straight and burr free.

• Slide nut and plastic sleeve (ferrule) onto supply tube. Ensure plastic sleeve is oriented as shown.
• Insert supply tube into supply valve connection. Supply tube should touch bottom of hole inside supply valve.

• Slide plastic sleeve down supply tube until it contacts the supply valve connection.

• Slide nut over plastic sleeve.

• Start nut by hand to prevent cross-threading.
  Turn nut by hand until it feels snug. Then tighten nut at least two more turns with a wrench.

• Repeat for other supply line.

• Return to regular instructions.

additional cut, being careful not to cut the tube too short.
Tubing is cut too short.| Buy a coupling union and a replacement supply line that mate together. The coupling union end
intended to connect to the faucet must mate to the standard 3/8” connection nuts and plastic sleeves
(ferrules) supplied with the faucet.
The plastic sleeve (ferrule) or connection nut is lost.| Purchase a replacement nut and/or plastic sleeve (ferrule) that are designed to seal with PEX tubing.

TROUBLESHOOTING

reinstalling aerator.
– SHUT OFF WATER SUPPLIES. Replace valve assembly. When reinstalling parts, ensure gasket is in place and bonnet nut is tightened securely with a wrench.
Faucet leaks from under handle.| Loose bonnet nut.| Using a wrench, ensure bonnet nut is tight.
If faucet continues to leak from handle:| SHUT OFF WATER SUPPLIES. Replace valve assembly. When reinstalling parts, ensure bonnet nut is tightened securely with a wrench.
Faucet leaks from spout outlet.| Valve issue.| – SHUT OFF WATER SUPPLIES. Replace valve assembly. When reinstalling parts, ensure bonnet nut is tightened securely with a wrench.
Water leaks from air gap module opening.| – The drain line tubing is looped, kinked, or has a low spot.
– The drain line is blocked or the drain hole is not drilled through completely. – Air is locked in the air gap outlet.
– There is excessive RO reject flow.| – Trim any excess tubing to obtain a short, “straight-shot” to the drain.
– Check to see that the drain line is clear of any obstruction and remove the drain saddle fitting to verify that the hole is drilled through completely.
– Blow air into the air gap outlet using a short length of tubing.
Noise in the drain (gurgling or dribbling sound).| The reject water is dripping into the standing water in the drain trap| – Make sure that the 3/8″ drain tubing from the faucet air gap module slopes continuously downward to the drain saddle without any loops or low spots.
– Angle the drain piping so that the reject water runs down the side of the drain pipe.
– Change the location of the drain saddle to the horizontal drain pipe or any alternate vertical
drain pipe which is farther from the trap. Properly plug the original hole. Drill larger hole in
drain pipe. Make sure the drain saddle is always installed above (before) the trap.
Airgap makes excessive noise.| – The reject water is dripping into the standing water in the water pipe.
– The drain line has a loop or low spot.
– The RO system requires an inline restrictor that was located in the line between the RO Waste line and Faucet.| The airgap included with this faucet does not include an inline flow restrictor that may be required for the existing RO filtration system. Reference the RO Systems Information to determine if an additional flow restrictor (not provided) needs to be added to the waste line coming from the RO system.

Limited Warranty on Brizo® Faucets

Parts and Finish. All parts (other than electronic parts, air switch power modules, batteries, and parts not supplied by Brizo Kitchen andBath Company) and finishes of Brizo® faucets purchased from authorized Brizo sellers are warranted to the original consumer purchaserto be free from defects in material and workmanship for as long as the original consumer purchaser owns the home in which the faucet wasfirst installed. For commercial purchasers, (a) the warranty period is ten (10) years for multi-family residential applications and (b) five (5)years for all other commercial uses, in each case from the date of purchase. For purposes of this warranty, the term “multi-family residentialapplication” refers to the purchase of the faucet from an authorized Brizo seller by a purchaser who owns but does not live in the residentialdwelling in which the faucet is initially installed, such as in a rented or leased single unit or multi-unit detached home (duplex or townhome),or a condominium, apartment building or community living center. The following installations are not considered multi-family residential applications, are excluded from the 10-year warranty, and are subject to the 5-year warranty: industrial, institutional or other business premises,such as a dormitory, hospitality premises (hotel, motel, or extended stay location), airport, educational facility, long- or short-term healthcarefacility (hospital, rehabilitation center, nursing, assisted or staged-care living unit), public space or common area.
Electronic Parts and Batteries (if applicable). Electronic parts (other than air switch power modules and batteries), if any, in Brizo® faucets purchased from authorized Brizo sellers are warranted to the original consumer purchaser to be free from defects in material and workmanship for five (5) years from the date of purchase or, for commercial users, for one (1) year from the date of purchase. No warranty is provided on batteries.
Air Switch Power Module. The electronic power module of Brizo® air switches purchased from authorized Brizo sellers is warranted to the original consumer purchaser to be free from defects in material and workmanship for two (2) years from the date of  purchase or, for commercial users, for one (1) year from the date of purchase.
What We Will Do. Brizo Kitchen & Bath Company will repair or replace, free of charge, during the applicable warranty period (as describedabove), any part or finish that proves defective in material and/or workmanship under normal installation, use, and service. Brizo Kitchen & Bath Company may, in its sole discretion, use new, refurbished or recertified parts or products for such repair or replacement. If repair or replacement is not practical, Brizo Kitchen & Bath Company may elect to refund the purchase price in exchange for the return of the product.These are your exclusive remedies.
What Is Not Covered. Because Brizo Kitchen and Bath Company is unable to control the quality of Brizo products sold by unauthorized sellers, unless otherwise prohibited by law, this warranty does not cover Brizo products purchased from unauthorized sellers (visit Brizo.com to see a list of our Authorized Online Resellers).
Any labor charges incurred by the purchaser to repair, replace, install or remove this product are not covered by this warranty. Brizo Kitchen& Bath Company shall not be liable for any damage to the product resulting from reasonable wear and tear, outdoor use, misuse (includinguse of the product for an unintended application), freezing water, abuse, neglect, or improper or incorrectly performed assembly, installation,maintenance or repair, including failure to follow the applicable care and cleaning instructions. Customized components purchased by theconsumer or commercial user and installed into a Brizo product, and any damage resulting from removal or improper installation of suchcomponents, are not covered by this warranty.
Brizo Kitchen & Bath Company recommends using a professional plumber for all installation and repair of faucets. We also recommend that
you use only genuine Brizo® replacement parts.
What You Must Do To Obtain Warranty Service or Replacement Parts. A warranty claim may be made and replacement parts maybe obtained by calling 1-877-345-BRIZO (2749) or by contacting us by mail or online as follows (please include your model number and dateof purchase):

In the United States and Mexico:
Brizo Kitchen & Bath Company
55 E. 111th Street
Indianapolis, IN 46280
Attention: Warranty Service
https://www.brizo.com/customer-support/contact-us| In Canada:
Masco Canada Limited, Plumbing Group
Technical Service Centre
350 South Edgeware Road
St. Thomas, Ontario, Canada N5P 4L1
https://www.brizo.com/customer-support/contact-us
---|---

Proof of purchase (original sales receipt) from the original purchaser must be made available to Brizo Kitchen & Bath Company for all warranty claims unless the purchaser has registered the product with Brizo Kitchen & Bath Company. This warranty applies only to Brizo® faucets installed in the United States of America, Canada, and Mexico.
Limitation on Duration of Implied Warranties. Please note that some states/provinces (including Quebec) do not allow limitations on how long an implied warranty lasts, so the below limitations may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, ANY IMPLIED WARRANTY, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY AND OF FITNESS FOR A PARTICULAR PURPOSE, IS LIMITED TO THE STATUTORY PERIOD OR THE DURATION OF THIS WARRANTY, WHICHEVER IS SHORTER.
Limitation of Special, Incidental or Consequential Damages. Please note that some states/provinces (including Quebec) do not allow the exclusion or limitation of special, incidental, or consequential damages, so the below limitations and exclusions may not apply to you. TO THE MAXIMUM EXTENT PERMITTED BY APPLICABLE LAW, THIS WARRANTY DOES NOT COVER, AND BRIZO KITCHEN & BATH COMPANY SHALL NOT BE LIABLE FOR ANY SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES (INCLUDING LABOR CHARGES TO REPAIR, REPLACE, INSTALL OR REMOVE THIS PRODUCT), WHETHER ARISING OUT OF BREACH OF ANY EXPRESS OR IMPLIED WARRANTY, BREACH OF CONTRACT, TORT, OR OTHERWISE. BRIZO KITCHEN & BATH COMPANY SHALL NOT BE LIABLE FOR ANY DAMAGE TO THE FAUCET RESULTING FROM REASONABLE WEAR AND TEAR, OUTDOOR USE, MISUSE (INCLUDING USE OF THE PRODUCT FOR AN UNINTENDED APPLICATION, FREEZING WATER, ABUSE, NEGLECT OR IMPROPER OR INCORRECTLY PERFORMED ASSEMBLY, INSTALLATION, MAINTENANCE OR REPAIR, INCLUDING FAILURE TO FOLLOW THE APPLICABLE INSTALLATION, CARE AND CLEANING INSTRUCTIONS. Notice to residents of the State of New Jersey: The provisions of this warranty, including its limitations, are intended to apply to the fullest extent permitted by the laws of the State of New Jersey.
Additional Rights. This warranty gives you specific legal rights, and you may also have other rights which vary from state/province
to state/province. This is Brizo Kitchen & Bath Company’s exclusive written warranty, and the warranty is not transferable.

If you have any questions or concerns regarding our warranty
please contact us as provided above or visit our website at
www.brizo.com
© 2022 Masco Corporation of Indiana

References

• Brizo.com
• brizo.com
• brizo.com/customer-support
• brizo.com/customer-support/product-registration
• brizo.com/customer-support/contact-us

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>