Neomounts by Newstar DS60-425WH1 Monitor Arm Desk Mount Instruction Manual

June 12, 2024
NEOMOUNTS BY NEWSTAR

Neomounts by Newstar DS60-425WH1 Monitor Arm Desk Mount

Product Information

Product Name: DS60-425WH1
Measuring Unit: mm
Weight Capacity: 0-8 kg | 0-17.6 lbs
Adjustable Height: 27.5-55.5 cm
Compatible VESA Sizes: 75×75, 100×100 mm
Manufacturer Website: www.neomounts.com

Product Usage Instructions

  1. Step 1: Clamp
    Mount the desk clamp to the rod and install the clamp to the desk

  2. Step 1: Grommet
    Mount the desk grommet to the rod and install the grommet in the desk.

  3. Step 2: Assemble Arm
    Assemble the arm and attach it to the rod.|

  4. Step 3: Attach Screen
    Screw 2 bolts in the upper 2 VESA holes of the screen, leaving 3mm spacing.

  5. Step 4: Slide Bolts
    Slide the bolts into the top holes of the VESA plate and tighten the bolts. Attach the other 2 bolts in the lower part of the VESA plate.

  6. Step 5: Cable Management
    Remove the cable cover and run the cable(s) through the cover.

  7. Step 6: Adjust Position
    If the display does not stop at your desired position, tighten the screw as shown.

Monitor desk mount

Neomounts-by-Newstar-DS60-425WH1-Monitor-Arm-Desk-
Mount-1

PARTS

Neomounts-by-Newstar-DS60-425WH1-Monitor-Arm-Desk-
Mount-3

INSTRUCTION

Clamp

STEP 1
Mount the desk clamp to the rod and install the clamp to the desk

Neomounts-by-Newstar-DS60-425WH1-Monitor-Arm-Desk-
Mount-5

Grommet

STEP 1
Mount the desk grommet to the rod and install the grommet in the desk

Neomounts-by-Newstar-DS60-425WH1-Monitor-Arm-Desk-
Mount-6Neomounts-by-Newstar-DS60-425WH1
-Monitor-Arm-Desk-Mount-7

STEP 2
Assemble the arm and attach it to the rod

Neomounts-by-Newstar-DS60-425WH1-Monitor-Arm-Desk-
Mount-8

STEP 3
Screw 2 bolts in the upper 2 VESA holes of the screen, leaving 3 mm spacing

STEP 4
Slide the bolts into the top holes of the VESA plate and tighten the bolts. Attach the other 2 bolts in the lower part of the VESA plate

Neomounts-by-Newstar-DS60-425WH1-Monitor-Arm-Desk-
Mount-11

STEP 5
Remove the cable cover and run the cable(s) through the cover

STEP 6
Adjust the mount to your desired position

STEP 7
Adjust the torque

Note: If the display does not stop at your desired position, tighten the screw as shown.

Neomounts-by-Newstar-DS60-425WH1-Monitor-Arm-Desk-
Mount-13

Neomounts-by-Newstar-DS60-425WH1-Monitor-Arm-Desk-
Mount-14

CAUTION

  1. To ensure safety, please read this manual carefully before installation and follow the instructions. Store this manual in a secure place for future reference.
  2. The manufacturer shall not be legally responsible for any equipment damage or personal injury caused by incorrect installation or operation other than that covered in this manual.
  3. The mount is designed for easy installation and removal. The manufacturer shall not be liable for damage to equipment or personal injuries arising out of human factors or acts of nature, such as earthquake or typhoon.
  4. It is recommended that the mount be installed by qualified personnel only.
  5. At least two persons are needed to install or remove the product to avoid hazard of falling objects.
  6. Please carefully inspect the area where the mount is to be installed:
    • Avoid places that are subject to high temperatures, humidity or contact with water.
    • Do not install the product near air conditioning vents or areas with excess dust and fumes.
    • Only install on vertical walls and avoid slanted surfaces.
    • Do not install in places subject to any shock or vibration.
    • Do not install in places subject to direct exposure to bright light, as it may cause eye fatigue when viewing the display panel.
  7. Maintain sufficient space around the display to ensure adequate ventilation.
  8. To ensure safe installation, first check the structure of the wall, ceiling or floor and select a secure mounting location.
  9. The wall, ceiling or floor should be strong enough to sustain a weight of at least four times of the display and mount combined. The mounting location must be able to withstand earhquake or other strong shock.
  10. Do not modify any accessories or use broken parts. Contact your dealer with any questions.
  11. Tighten all screws (do not exert excessive force to avoid breaking the screw or damaging its thread).
  12. Drill holes and bolts will be left in the wall, ceiling or floor once the display and bracket are removed. Stains may occur after extended use.
  13. Since the manufacturer has no way to control the wall, ceiling or floor type and installation of the mount, the warranty of the product shall only cover the body of the mount. The warranty period of the product is 5 years.
  14. Please consult the English language manual for any dispute on conditions.

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals