PHILIPS BGP501 Iridium Gen4 Instructions
- June 12, 2024
- Philips
Table of Contents
PHILIPS BGP501 Iridium Gen4
WHAT’S IN THE BOX
FEATURES
- Standard Luminaire housing is IK10.
- All added connectors are rated IK09.
| LED COLOUR | 722 | 727 | 730 | 740 | 757 | 830 |
|---|---|---|---|---|---|---|
| Light Source Energy Efficiency Class | E | E | D | D | D | E |
DIMENSION
CAUTION
SR compatibility: For SR based luminaires only SR Certified components/sensors are to be used (see also: http://www.lighting.philips.co.uk/oem-emea/products/driving-connected- lighting). Functional compatibility of 2 (SR certified) components/sensors to be used in combination as well as override possibility of any line-switch function used in a SR based luminaire, is to be released by the master component/sensor supplier. For the use of NEMA 7pin socket on a SR based luminaire a full system verification is required. Not following these advises can/will cause risk of damage and non-compliance for which Signify cannot take 2l any responsibility.
Version
Version with cable
Version without cable
- Disconnect before servicing
INSTALLATION INSTRUCTION
Dynadimmer
components
Disconnect before servicing
This product contains a light source of energy efficiency class: see table or label. Luminaire has basic insulation between Low Voltage supply and control conductors. Storage, installation, use, operation, and maintenance of the products need to be performed exactly according the instructions in this manual and/or other instructions as may be provided by us to guarantee safe use of the product over its entire lifetime. Failure to adhere to these instructions will invalidate your entitlement to warranty. Bolts with an indication of torque strength on the drawing need to be tightened using a calibrated torque wrench. Pre-assembled bolts need to be retightened again to the required torque specification to assure maximum strength over a lifetime. The light source and/or control gear and/or the external flexible cable contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similarly qualified person. The luminaire should be positioned so that prolonged staring into the luminaire at a distance closer than 25cm is not expected. Zhaga-D4i and SR-certified compatibility – For Zhaga-D4i/SR-Certified based luminaires only Zhaga-D4/SR-Certified components/sensors are to be used see also: https://www.zhagastandard.org/products https://www.lighting.philips.co.uk /oem-emea/products/driving-connected-lighting). The functional compatibility of two SR-certified and/or Zhaga-D4i controllers/sensors to be used in combination, as well as the override possibility of any line-switch function used in an SR-based/Zhaga-D4i luminaire, is to be released by the master controller/sensor supplier. If using a NEMA 7-pin socket on an SR-based luminaire, a full system verification is required. Not following this advice can/will cause risk of damage and non-compliance for which Signify cannot take any responsibility.
Annex I: Simplified EU Declaration of Conformity
Hereby, Signify Holding declares that the radio equipment type included into
the luminary is in compliance with Directive 2014/53/EU. The full text of the
EU Declaration of conformity is available at the following internet address:
http://www.philips.com/lighting
Signify Holding
Hereby, declares that the radio equipment type is in compliance with Directive 2014/53/EU. The full text of the EU Declaration of conformity is available at the following internet address: http://www.philips.com/lighting
- 2021 Signify Holding All rights reserved. This document contains information relating to the product portfolio of Signify which information may be subject to change. No representation or warranty as to the accuracy or completeness of the information included herein is given and any liability for any action in reliance thereon is disclaimed. The information presented in this document is not intended as any commercial offer and does not form part of any quotation or contract. Philips and the Philips Shield Emblem are registered trademarks of Koninklijke Philips N.V.. All other trademarks are owned by Signify Holding or their respective owners.
- Signify Holding The Netherlands
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>