UNITED SHF1179 Intelligent Electronic Safe User Manual
- June 12, 2024
- UNITED
Table of Contents
- UNITED SHF1179 Intelligent Electronic Safe
- MOUNTING METHOD
- Schematic drawing of case
- Schematic drawing of the control panel
- OPENING YOUR SAFE FOR THE FIRST TIME
- INSERTING THE BATTERIES
- OPENING DOOR
- AUTOMATIC LOCK
- SETTING THE USER CODE
- SETTING MASTER CODE
- OPENING THE SAFE WITH THE EMERGENCY KEY
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
UNITED SHF1179 Intelligent Electronic Safe
MOUNTING METHOD
- Fix the safe in the place which is not easy to move.
- Drill holes for expansion bolts (or clamping screws) in the right place.
- Turn the expansion bolts counterclockwise to separate.
- Use the expansion bolts (or clamping screws) to secure the case to the wall.
- Make sure the case is mounted in place as required and then tighten all screws. @ CAUTION: Use the expansion bolt when there is a concrete wall surface. Use the clamping screw when there is a wooden wall surface
For any help, kindly consult the local distributor
NOTICE ABOUT RECYCLING
‘Q” Your product is designed and manufactured with high-quality materials and components ~ which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. Please dispose of this equipment at your local community waste collection/ recycling center. In the European Union, there are separate collection systems for used electrical and electronic products. Please help us to conserve the environment we live in!
Schematic drawing of case
Schematic drawing of the control panel
- Bolts
- eset Button
- Battery Compartment
- Knob (Master Key)
- Emergency Lock Cover
- Green Light
- Red Light
- Yellow Light
- Confirming button
CAUTION : All drawings in this manual have been prepared based on the EA. The exterior design or component positions of other models may be different from what is indicated in the drawings, while the operation is the same.
OPENING YOUR SAFE FOR THE FIRST TIME
- Upon first opening, users should open the safe with the emergency key. The operation in details refers to ·’ opening the safe with the emergency key”.
- Remove the emergency lock cover. then insert the emergency key, and turn it counter clockwise.
- Turn the knob (master key) clockwise to open the door.
CAUTION: Finish the operation, pull out the emergency key and keep ii in a safe place.
INSERTING THE BATTERIES
- Open the door.
- Insert 4 X 1.5V batteries into the battery compartment.
- Under normal conditions, if both of the red and the green lights are on at the same time, it means the voltage is low and you should insert new batteries. 0 CAUTION: Replace 4 fresh batteries by lining them up in a manner as indicated by the “+ ” and ” – ” signs. When outage for longer than thirty minutes, you should reset the user’s code.
OPENING DOOR
- Input your user’s code (3 to 8 digits), each pressing results one buzzer beep and yellow light flashes.
- Press “A” (C /#)or “B” (E /*)button, the green light will be on.
- Rotate the knob (master key) clockwise and pull outwards within 5 seconds, the door is opened.
0 CAUTION: The user preset code “159··. Please input the user code again if the yellow light flashes with three buzzer beeps.
AUTOMATIC LOCK
- 3 continuously wrong entries will activate the warming beep for 20 seconds.
CAUTION :The keypad would be disabled during the beeping. You can only stop the beeps by opening the safe with an emergency key and power-cut by removing the battery.
SETTING THE USER CODE
- With the door open, press the reset button one, and start setting the code when the yellow lights goes on.
- Input new code (3-8 digits), and press the “A” (CI#) or “B” (E /*)button to confirm with 2 buzzer beeps, which indicates the acceptance and storage of the new code.
- If the yellow light flashes with 3 buzzer beeps, which means the code changing is not effective, and you need to try again.
SETTING MASTER CODE
- Open the safe, input “O” twice and press the reset button, start setting the code when the yellow light goes on.
- Input the new master code (3-8 digits), then press the “A” (CI#) or “B” (E /*) button to confirm, it will be confirmed by 2 beeps and the yellow light flashes two times, then setting is done successfully.
- If the yellow light flashes three times, it means the new code is invalid and should operate again.
OPENING THE SAFE WITH THE EMERGENCY KEY
Upon first receipt of the safe, or either the electronic circuit malfunction or codes unknown. You could also use the emergency key to open the safe.
- Remove the cover of the emergency lock.
- Insert the emergency key, turn it count clockwise, then turn the knob (master key) clockwise to open the door.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>