milwaukee IR PL250 USB Rechargeable Pen Light Instruction Manual

: June 12, 2024
: Milwaukee

Table of Contents

milwaukee IR PL250 USB Rechargeable Pen Light
Product Information
Product Usage Instructions
Description
TECHNICAL DATA
SPECIFIED CONDITIONS OF USE
FUEL GAUGE
BATTERIES
TRANSPORTING LITHIUM BATTERIES
MAINTENANCE
SYMBOLS
Contact Information
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

milwaukee IR PL250 USB Rechargeable Pen Light

Product Information

The product is the IR PL250. It comes with important operating and safety instructions that should be read and saved for future reference. The product is available in multiple languages, including English, Deutsch, Italiano, Nederlands, Dansk, Norsk, Svenska, Suomi, and IR PL250.

Technical Data

Battery-Lamp
Lighting time with one fully charged battery:
- Mode High: 2.0 hours
- Mode Low: 8 hours
Luminous flux:
- Mode High: 250 lm
- Mode Low: 50 lm
Charging time: 120 minutes
Colour rendering index: 80
Colour temperature: 4000 K
Laser output power: 1 mW
Laser beam divergence: 0.5 mrad
Laser point wavelength: 650 nm
Pulse Laser Cdularasstio..n…t.P: 50.2s
Weight: 0.06 kg
Protection class: IP 67

Product Usage Instructions

Read and familiarize yourself with the important operating and safety instructions provided in the user manual.
Ensure the product is charged before use by connecting it to a DC power source with a voltage of 5V and a current range of 0.1 – 0.5A.
To turn the product on or off, use the ON/OFF switch.
The product has different modes. Use the MODE button to switch between modes.
Press and hold the MODE button for 0.75 seconds to activate a specific mode.
The product has a battery-lamp feature that provides lighting. The lighting time depends on the mode selected:
- Mode High: 2.0 hours
- Mode Low: 8 hours
The product’s luminous flux also varies based on the mode:
- Mode High: 250 lm
- Mode Low: 50 lm
The product can be charged fully in approximately 120 minutes.
The product has a colour rendering index of 80 and a colour temperature of 4000 K.
Ensure to handle the product’s laser output power of 1 mW with caution.
The laser beam divergence is approximately 0.5 mrad and the laser point wavelength is 650 nm.
The product weighs 0.06 kg and has a protection class rating of IP 67.

Description

$milwaukee-IR-PL250-USB-Rechargeable-Pen-Light-fig- $1$$

TECHNICAL DATA

Rated Power Output …………………………………………………………………………………. 3 W
USB Input ………………………………………………………………………….5V DC; 0,1 A – 0,5 A
Lighting time with one fully charged battery
- Mode High …………………………………………………………………………………………..2,0 h
- Mode Low………………………………………………………………………………………………8 h
Luminous flux
- Mode High ………………………………………………………………………………………..250 lm
- Mode Low…………………………………………………………………………………………..50 lm
Charging time ………………………………………………………………………………………120 min
Colour rendering index ………………………………………………………………………………….80
Colour temperature ………………………………………………………………………………. 4000 K
Laser output power ……………………………………………………………………………… ≤ 1 mW
Laser beam divergence ……………………………………………………………………….0,5 mrad
Laser point wavelength ………………………………………………………………………….650 nm
Pulse duration tP ……………………………………………………………………………………≤ 50 μs
Laser Class …………………………………………………………………………………………………..2
Weight …………………………………………………………………………………………………0,06 kg
Protection class ………………………………………………………………………………………. IP 67
Recommended ambient operating temperature ………………………………… -20…+40 °C
Recommended ambient charging temperature ………………………………….. +5…+40 °C
Recommended USB power supply……………………………………………………………CUSB

WARNING!
Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fi re and/or serious injury. Save all warnings and instructions for future reference.

SAFETY INSTRUCTIONS BATTERY-LAMP

WARNING: Use only the recommended USB cable and charger.
Warning: Do not direct the light beam at persons or animals and do not stare into the light beam yourself (not even from a distance). Staring into the light beam may result in serious injury or vision loss.
WARNING: It is a Class 2 laser product in accordance with EN60825-1:2014.
CONSUMER LASER PRODUCT
EN 50689:2021
Warning:
- Avoid direct eye exposure. The laser beam can cause flash blindness.
- Do not stare into the laser beam or direct it towards other people unnecessarily.
- Don’t dazzle other individuals.
Warning:
- Do not operate the tool around children or allow children to operate the tool.
- The reflective surface could reflect the beam back at the operator or other persons.
- Do not look into a laser beam using magnifying optical devices such as binoculars or a telescope, as this will increase the level of eye injury.

SAFETY INSTRUCTIONS BATTERY
Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it off immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately seek medical attention.

Warning!
To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE

The Battery-lamp is intended to be used light independent use away from mains supply.
The Battery-lamp can be used as a laser pointer.
Do not use this product in any other way as stated for normal use. $milwaukee-IR-PL250-USB-Rechargeable-Pen-Light-fig- $2$$ $milwaukee-IR-PL250-USB-Rechargeable-Pen-Light-fig- $3$$

CHARGING
Plug your USB cable into a power source such as an AC wall adaptor, computer or carport.

The indicator light will display the charging status:

Red flashing: charging, 0-49% charged
Yellow flashing: charging 50-99% charged
Green solid: 100% charged
Red Solid: Hot Battery
Red/Green Flashing: Cold, Wet, or Faulty

If the light continues to flash red and green, the battery may be cold, wet, faulty, or the battery did not fully charge after 12 hours. If the light is solid red, the battery is too hot. Allow the battery to cool down, warm up, or dry out. Turn the light on or plug it in for charging. If the problem persists, contact a MILWAUKEE service facility.

FUEL GAUGE

The fuel gauge will display the battery life:

Red flashing: < 3% remaining
Red solid: 3-9% remaining
Yellow solid: 11-49% remaining
Green solid: 50-100% remaining

BATTERIES

Batteries which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery. Avoid extended exposure to heat or sunshine (risk of overheating).
For an optimum life-time, the batteries have to be fully charged, after used.

For battery storage longer than 30 days:

Store the battery where the temperature is below 27°C and away from moisture
Store the battery in a 30% – 50% charged condition
Every six months of storage, charge the battery as normal.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements. Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.

The user can transport the batteries by road without further requirements.
Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.

When transporting batteries:

Ensure that battery contact terminals are protected and insulated to prevent short circuit.
Ensure that battery pack is secured against movement within packaging.
Do not transport batteries that are cracked or leak.

Check with forwarding company for further advice

MAINTENANCE

The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced. Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).

If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit No. on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.

Please visit our website www.milwaukeetool.eu for further information on warranty conditions and registration.

SYMBOLS

Please read the instructions carefully before starting the machine.
CAUTION! WARNING! DANGER!
Warning of laser radiation
Laser Class 2 product
Do not stare at the operating light source.
Connection USB
Class III electrical protection.
Do not dispose of waste batteries, waste electrical and electronic equipment as unsorted municipal waste. Waste batteries and waste electrical and electronic equipment must be collected separately. Waste batteries, waste accumulators and light sources have to be removed from the equipment. Check with your local authority or retailer for recycling advice and collection point. According to local regulations, retailers may have an obligation to take back waste batteries and Waste electrical and electronic equipment free of charge. Your contribution to the re-use and recycling of waste batteries and waste electrical and electronic equipment helps to reduce the demand for raw materials. Waste batteries, in particular containing lithium and waste Electrical and electronic equipment contain valuable, recyclable materials, which can adversely impact the environment and human health, if not disposed of in an environmentally compatible manner. Delete personal data from waste equipment, if any.
European Conformity Mark
UK Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark