AcraDyne AEP4A12003B Pistol Motor Assembly Instruction Manual
- June 12, 2024
- AcraDyne
Table of Contents
AcraDyne AEP4A12003B Pistol Motor Assembly Instruction Manual
Product Overawe
COMMENTS | ITEM NO. | NUMBER | QTY. | DESCRIPTION |
---|---|---|---|---|
1 | 25803 | 1 | PISTOL MOTOR ASM. | |
2 | 26599 | 1 | LED PCB ASSY, PISTOL | |
3 | 27016 | 2 | NUT. HEX, 4-40 UNDERSIZED, STEEL ZINC | |
4 | 24780 | 1 | MOTOR COUPLER SUB-ASM. | |
5 | 25763 | 1 | TRANSDUCER ADAPTOR | |
6 | SEE CHART | 1 | TRANSDUCER SUB-ASM. | |
7 | SEE CHART | 1 | GEAR CASE SUB-ASM. | |
8 | 24699 | 1 | STRAIGHT OUTPUT ASM., 3/8″ SQ. DR. | |
9 | 24687 | 1 | 0-RING, LIGHT RING, LEVER | |
10 | 24873 | 1 | LIGHT RING | |
11 | 24686 | 1 | RETAINING RING, LEVER LIGHT RING | |
12 | 25814 | 2 | SCREW, PAN HEAD PHILLIPS, 4-40 x 3/16, STAR WASH, SS | |
13 | 25849 | 1 | TID BOARD ASM.. PISTOL. 1000/2000-SERIES | |
14 | 24934 | 2 | SCREW, FHC 4-40 X .312, STEEL, BLACK OXIDE | |
15 | 26667 | 1 | PISTOL HANDLE, 1000 SERIES | |
16 | 25871 | 1 | SWITCH SUB-ASSEMBLY | |
NOT SHOWN | 17 | 25788 | 1 | CABLE, TRIGGER. GEN 4 PISTOL |
18 | SEE CHART | 1 | REACTION BAR, 1000 SERIES | |
19 | 26792 | 4 | SCREW. BHSC 6-32X.50. STEEL. BLACK OXIDE | |
20 | 26791 | 4 | WASHER. FLAT, NO 6 SCREW, STEEL. BLACK OXIDE | |
21 | 25424 | 1 | GROUND WIRE ASM. | |
22 | 24870 | 1 | CONNECTOR SLEEVE, PISTOL HANDLE | |
23 | 25271 | A/R | SHIM. – .002 | |
24 | 25272 | A/R | SHIM. – .005 | |
25 | 25273 | A/R | SHIM. – .010 | |
26 | 26602 | 1 | TOOL CONNECTOR ASSEMBLY | |
27 | 24935 | 2 | SOC HD CAP SCREWS | |
28 | 24871 | 1 | END CAP, PISTOL MOTOR | |
29 | SEE CHART | 1 | SPLINE COVER, PISTOL | |
30 | 010-790-1 | 1 | SUSPENSION BAIL, PISTOL TOOLS | |
MODEL NO. | TRANSDUCER | |||
ASM. | GEAR CASE ASM. | SPLINE COVER | REACTION BAR | |
--- | --- | --- | --- | --- |
SINGLE STEP
MODELS| AEP4Al2003B| 25759.| 24860| 24759| N/A
AEP4Al2006B| 25760.| 24860| 24759| N/A
DOUBLE STEP
MODELS| AEP4Al2011B| 25761.| 24709| N/A| 24696
AEP4Al2014B| 25761.| 24792| N/A| 24697
AEP4Al2018B| 25761.| 24710| N/A| 24697
AEP4Al2022B| 25761.010| 24781| N/A| 24697
ASSEMBLY INSTRUCTIONS
SUB-ASSEMBLY
- GEARS & SPLINES: LUBRICATE WITH DOW CORNING MOLYKOTE BR2 PLUS GREASE.
- BEARINGS: LUBRICATE WITH CHEVRON SR1 GREASE
- O-RINGS: LUBRICATE WITH O-RING LUBE’
- TIGHTEN TO 1.0 Nm (9 IN-LBS.) LOCTITE 222 (PURPLE)
REQUIRED TOOLING
- SNAP-ON CROWFOOT WRENCH, 1/2″ SQ. DR. X 1-3/8″ OPENING SNAP-ON PART NUMBER SC044
- MAGNETIC VISE JAWS – PART NUMBER 1000-100
- LOCTITE 222 (PURPLE)
- LOCTITE 243 (BLUE)
- LOCTITE 263 (RED)
- TORQUE WRENCH, 1/2″ DRIVE
MODEL NO.|
---|---
SINGLE STEPMODELS| AEP4Al2003B
AEP4Al2006B
DOUBLE STEPMODELS| AEP4Al2011B
AEP4Al2014B
AEP4Al2018B
AEP4Al2022B
DOCUMENT CONTROL
PRINTED COPIES OF THIS DOCUMENT ARE CONSIDERED TO BE UNCONTROLLED DOCUMENTS. HOLDERS ARE RESPONSIBLE FOR VERIFYING THE CURRENT REVISION LEVEL WITH PURCHASING OR ENGINEERING PRIOR TO USE OR FABRICATION. THE CONTROLLED VERSION OF THIS DOCUMENT IS ELECTRONICALLY MAINTAINED.
PROPRIETARY AND CONFIDENTIAL
THIS DRAWING CONTAINS INFORMATION STRICTLY 30′ CONFIDENTIAL TO ACRADYNE/AIMCO. IN THE ABSENCE OF EXPRESSED WRITTEN PERMISSION, ACRADYNE/AIMCO HAS LOANED THIS COPY WITH THE MUTUAL UNDERSTANDING THAT (A) IT WILL NOT BE USED FOR ANY PURPOSE OTHER THAN FOR THAT IN WHICH IT WAS PROVIDED, (B) THE DATA AUTHOR/ CONTAINED HEREIN WILL NOT BE DISCLOSED TO OTHERS, (C) IT WILL NOT BE REPRODUCED, AND (D) IT WILL BE RETURNED TO ACRADYNE/AIMCO IMMEDIATELY UPON DEMAND.
REVISION LEVEL
REVISION RELEASE DATE
DESCRIPTION OF CHANGES MADE TO PART
ECN #
AUTHOR APPROVAL
UNLESS OTHERWISE SPECIFIED, DIMENSIONS ARE IN INCHES
DIMENSIONS AND TOLERANCING PER ANSI Y14.5 SURFACE ROUGHNESS PER ANSI Y14.36
BLOCK TOLERANCING PER DECIMAL
X = .030 .XX = .010 .XXX = .005 .XXXX = .0005 ANGLE =
REMOVE BURRS AND SHARP EDGES: R.015 MAX MACHINE SURFACE FINISH: 125 RMS OR BETTER
DRAWINGS AND TECHNICAL DOCUMENTS CONTROLLED BY:
ACRADYNE MECHANICAL ENGINEERING
PISTOL NUTRUNNER GEN IV, 1000 SERIES
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>