HiVi SWANS OS-10 Multimedia Active Speaker User Manual

HiVi SWANS OS-10 Multimedia Active Speaker

IMPORTANT SAFETY INSTRUCTIONS

WARNING
To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture.
CAUTION

DO NOT OPEN
RISK OF ELECTRIC SHOCK
The lightning flash is intended to alert you to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute an electric shock to persons.

The exclamation point is intended to alert you to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.
Before connecting or using this apparatus, do read carefully all safety warnings and instructions. Please keep this instruction for future reference.
This device should be installed or set up in a position where ventilation can be assured. Never put the device in a place where airflow over the ventilation openings might be hindered, such as in a bookshelf or a drawer.
This product should be operated only from the type of power source indicated on the back panel of the device. The power cord of this product should be restored in a place that is less possibly be walked on or get pierced, especially its plug, convenience receptacles, and the point where the power cord exit from the apparatus.
Before cleaning this product, make sure the plug is disconnected from the outlet. Proceed with the cleaning in the way that this instruction recommends only.
When this product is not in use for a long time, make sure to unplug the power cord from the AC outlet.
If below problem happens, send this product to qualified service personnel for repair.

1. Power cord or power plug is damaged.
2. Objects have fallen or liquid has been spilled into this product.
3. This product is exposed to rain or other liquid.
4. This product functions abnormally or very poorly.
5. This product has been dropped or has a damaged enclosure.
   Never to attempt to repair this product by yourself. Refer all servicing to a qualified servicing personnel.

CAUTION
To reduce the risk of electric shock, the power plug must be completely inserted into an AC outlet.
This product does not contain any parts or components that can be repaired by users themselves. Do not open the enclosure, otherwise it may result in an electric shock. Refer all servicing to a qualified servicing personnel.
When you unplug this product from AC outlet, do hold the power plug and pull.
Do not pull the power cord. Do not overload AC outlets or the extension cord, as this can lead to risk of fire or electric shock.

After-Sales services

If you still could not resolve your issue, please contact the seller for customer service.

Notice

1. Using the same type or similar type of battery, otherwise it may cause explosion.
2. Keep the battery away from sunlight, heat or fire.
3. Please remove batteries from the remote, if it is not used for a long time.
4. If the battery is aged, the effective control distance of the remote will be less. Change the battery when this happens.
5. Please abide by your local regulations when discarding the battery. Please do not discard the battery along with other rubbish.
6. This icon means this product is a CLASS II device or it comes with double insulation. It does not need earth lead.
7. This icon means this product is only suitable for indoor use.

Warning

When repairing or replacement of parts is required, make sure the service technician has used the parts/components specified by the manufacturer or parts/components that have the same characteristics as the original parts/components. Unauthorized substitutions may result in risk of fire, electric shock or other hazards.

POWER SOURCE
Before connecting this product with AC outlet, do check and make sure the electric supply voltage is as same as it is marked on the rear panel of this product.
WARNING: It’s very dangerous to insert a power plug that has bare wire into an AC outlet.

DECLARATION
This product does not contain any parts or components that can be repaired by users themselves. If there is any malfunction, refer to this instruction or ask for repair by a qualified service technician. Do not try to repair by yourself, otherwise the manufacturer will not be responsible for any consequences resulted there from.

FCC Warning

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:
(1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation. NOTE 1:
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

NOTE
Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Unpacking & Schematic Diagram

Please make sure all the following components are in the box.

Break-in

Break-in is the procedure which can enable the speakers to perform best acoustically. A period ranging from 48-100 hours of usage is recommended before both the amplifier and speaker drivers behave optimally.
Alternatively, you can listen 2 or 3 hours every day at a medium volume, and the speakers will be broken-in one month or so.

Maintenance

1. Avoid magnetic disturbance.
2. Do not place under the sunshine for a long time.
3. Do not place in high temperature or moist environment for a long time.
4. Do not touch the drivers with your hands.
5. Avoid corrosive liquids and gases.

Trouble Shooting

1. If there is problem with sound quality.
2. Check if all the drivers are working.
3. Check that audio cables are firmly connected at both ends.
4. If there is no sound from either of the speakers:
5. Check if the device is on and if a source is playing.
6. Check if the volume is not on a minimum.
7. Check if there is a broken or short circuit with the cable connecting speakers and audio source.
8. If there is no sound coming from one of the speakers:
9. Check the setting of the audio source.
10. Check that all the audio cable are firmly connected at both ends.

Speaker Placement

Specifications

Unpacking & Schematic Diagram

1. Tweeter
2. Receiver / Indicator Light
3. Woofer
4. Dual RCA to 3.5mm Audio Cable
5. Speaker Connection Cable
6. Optical Connecting Cable
7. Power
8. AUX Input (Light Blue Light)
9. Coaxial Input(Purple Light)
10. INPUT
11. Volume Down
12. Power button on touch panel
13. Optical Input (White Light)
14. Bluetooth Input (Blue Light)
15. Mute (Red Light)
16. Volume Up
17. Optical Interface
18. AUX Interface
19. Speaker Out
20. Coaxial Interface
21. Power Cable
22. Speaker In
23. Long press to power on or enter standby mode
24. Input selects
25. Press to increase the volume
26. Press to decrease the volume
27. Mute(When flash in red, product is in silent)

Remark:
Touch panel lights on when power on. Light off function works after the operation of standby and product on.
Touch panel lights off if not operations in 5 minutes. Touch the function buttons on the panel to wake up the light.

Speaker Connection

1. The connection between speakers.
2. Speaker connection with power.
3. Optical connection with CD Player/DVD Player/TV.
4. Speaker connection with computers, TV or tablets etc.

Bluetooth Connection

Select Bluetooth mode via the remote control or button on top. The indicator light should flash blue. Choose HiVi-Swans OS-10 on your phone. Steady blue light indicates successful Bluetooth connection.

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>