EverFocus EHA1281 eZ.HD Series 1080p Dual Power FHD IP66 IR Dome Camera Instruction Manual
- June 12, 2024
- EverFocus
Table of Contents
EverFocus EHA1281 eZ.HD Series 1080p Dual Power FHD IP66 IR Dome Camera Instruction Manual
Copyright © EverFocus Electronics Corp.
Release Date: November, 2022
All the images including product pictures or screen shots in this document are
for example only. The images may vary depending on the product and software
version. Information contained in this document is subject to change without
notice.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng Dist., New Taipei City 222,
Taiwan
TEL: +886 2 2662 2338 FAX: +886 2 2662 3632
www.everfocus.com.tw
1. Introduction
Equipped with a 1080p Sony CMOS sensor, the EHA1281 deliver 1080p full HD image quality. The model provides 2.8-12mm lens with ICR. Featured with Digital Wide Dynamic Range (D-WDR), the camera can provide clear images even under backlight circumstances where intensity of illumination can vary excessively. The EHA1281 supports dual power (12VDC / 24VAC) and supports both NTSC and PAL scanning systems.
1.1 Packing List
Camera x 1
Mounting Sticker x 1
L-Type Wrench x 1
Screw & Screw Anchor x 4
Desiccant Bag x 1
User Manual x 1
1.2 Features
- 1080p Sony CMOS sensor, delivering amazing high sensitivity
- Varifocal 2.8-12mm with ICR to capture the desired field of view
- Extended IR range of up to 30m / 98ft. with 30 LEDs (depends on scene IR reflectivity)
- D-WDR to improve the visibility under high contrast scene
- 3-Axis rotation design allows wall or ceiling mounting
- IP66-rated with metal housing
- Supports dual power (12VDC / 24VAC)
- Supports UTC function: Control camera OSD settings directly from DVR end
1.3 Dimensions
1.4 Optional Accessory
1.5 Cable Description
2. Installation
1. Stick the supplied Mounting Sticker to the surface to mark the 4 screw positions. Drill four holes on the surface and insert the supplied 4 Screw Anchors into the screw holes. If you want to run the cable through the surface, drill a hole within the 4 screw area.
2. To mount the camera to the surface:
- a. Remove the Base Plate from the camera. To do so, 1) Remove the Fix Screw 2) Slightly push the Base Plate backward from the Fix Screw side and then pull out the Base Plate. Screw the Base Plate to the surface using the supplied 4 Screws.
- b. Open the Camera Cover to remove the old desiccant bag from the Camera Body and stick the supplied Desiccant Bag inside the Camera Body. It’s highly recommended to replace the desiccant bag every time when you open the Camera Cover.
Note: Please screw back the Camera Cover immediately in case of reducing the absorption capacity of the desiccant bag inside the camera body. - c. For the first time installation, check whether the camera is properly focused. If not, you can optionally adjust camera zoom and focus by adjusting the Zoom Screw or Focus Screw using a slotted screwdriver.
- d. Attach the Camera Body to the Base Plate. Screw back the Fix Screw.
3. Connect the Power Cable to a 12VDCpower source. Connect the Video Output Cable to a monitor or DVR.
4. You can use the Joystick on the cable to configure camera OSD settings or switch to different video formats. Remove the Protection Cap from the Joystick before using it.
Switching Video Format:
Push the joystick up for 5 sec. to switch to resolution1080p/720p.
Push the joystick right for 5 sec. to switch to AHD.
Push the joystick down for 5 sec. to switch to NTSC/PAL.
Push the joystick left for 5 sec. to switch to CVBS.
Push the joystick center to enter main menu.
Configuring OSD Settings:
Push the Joystick up / down to select among menu items.
Push the Joystick left / right to adjust the level of the selected item.
Press the Joystick to enter the sub-menu or exit the OSD Setup Menu.
5. You can optionally adjust the camera angles. To do so, unscrew the 4 cover screws using the supplied L-Type Wrench and then remove the cover. Adjust the camera angles (Tilt: 90°, Pan: 180°, Rotate: 90°). After adjusting camera angles, screw back the camera cover.
3. Configuration in the OSD Menu
You can configure camera settings in the OSD menu from DVR end.
EverFocus Electronics Corp.
EverFocus Taiwan:
2F., No.12, Ln. 270, Sec. 3, Beishen Rd., Shenkeng
Dist., New Taipei City 222, Taiwan TEL: +886 2 2662
2338 FAX: +886 2 2662 3632
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus China – Shenzhen:
2F, Building A, Area A, Longquan Science and
Technology Park,Tongfuyu Phase II, Henglang
Community, Dalang Street, Longhua,Shenzhen
518109, Guangdong, China TEL: +86 755 2765
1313 FAX: +86 755 2765 0337
www.everfocus.com.tw
marketing@everfocus.com.tw
EverFocus USA – California:
324 W Blueridge Avenue, Orange, CA 92865, USA
TEL: +1 626 844 8888 FAX: +1 714 792 0481
www.everfocus.com
sales@everfocus.com
EverFocus Japan – Tokyo:
7-6-4-101 Takashimadaira, Itabashi-ku, Tokyo
175-0082, Japan TEL: +81 (3) 4363-2819 FAX: +81
(3) 4363-2790
www.everfocus.co.jp
sales@everfocus.co.jp
Your EverFocus product is designed and manufactured with high quality materials and components which can be recycled and reused. This symbol means that electrical and electronic equipment, at their end-of-life, should be disposed of separately from your household waste. Please, dispose of this equipment at your local community waste collection/recycling centre. In the European Union there are separate collection systems for used electrical and electronic product. Please, help us to conserve the environment we live in!
References
- EverFocusエレクトロニクス株式会社、AIのリーダー、ビデオ分析
- EverFocus, the expert of smart image analytics leading AI edge, CCTV, and mobile DVR Supplier
- EverFocus, the expert of smart image analytics leading AI edge, CCTV, and mobile DVR Supplier
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>