SENA 10S Motorcycle Bluetooth Communication System User Manual
- June 12, 2024
- Sena
Table of Contents
10S Motorcycle Bluetooth Communication System
User Manual
10S Motorcycle Bluetooth Communication System
Charging
Red LED: Charging
Blue LED: Fully charged
Power On/Off
Press and hold the Jog Dial and Phone Button for 1 second Tap the Jog Dial and
Phone Button.
Volume Adjustment
Increase/Decrease the volume : Rotate the Jog Dial clockwise or
counterclockwise
Battery Check
Phone, Music Pairing
Initially Pairing the headset The headset will automatically enter the phone pairing mode when you initially turn on the headset or in the following situation:
- Rebooting after executing Factory Reset
1. Press and hold the Jog Dial and Phone Button for 1 second.
2. Search for Bluetooth devices on your mobile phone. Select the headset in the list of the devices detected on the mobile phone.
3. Enter 0000 for the PIN. Some mobile phones may not ask for the PIN.
Music Operation
Play or pause music: Press and hold the Jog Dial for 1 second. Track forward/
back: Rotate while pressing the Jog Dial clockwise or counterclockwise.
Mobile Phone Call Makina and Answering
Answering a call: Tap the Phone Button Ending a call: Tap the Phone Button
Voice dial: Tap the Phone Button Speed dial: Double tap the Phone Button
Rejecting a call’ Press and hold the Jog Dial for 2 seconds.
Intercom
Intercom Pairing
- Press and hold the Jog Dial of two headsets for 5 seconds until red LEDs of both units start to flash rapidly.
- Simply tap the Jog Dial of any one of the two headsets.
Intercom Start/End : Tap the Jog Dial.
Setting
Configuration Menu: Press the Jog Dial for 10 seconds.
Using the Sena Device Manager
Connect the headset to your computer via a USB cable. Launch the Sena Device
Manager and click DEVICE SETTING to configure the headset settings.
For details about downloading the Sena Device Manager, please refer to the
leaflet included in the package.
Troubleshooting
Factory Reset
If you want to restore the headset to factory default settings, Press and hold
the Phone Button for 10 seconds and tap the Jog Dial . The headset
automatically restores the default settings and turns off.
Certification and Safety Approvals FCC Compliance Statement
This device complies with part 15 of the FCC rules. Operation is subject to
the following two conditions:
- This device may not cause harmful interference, and
- This device must accept any interference received, including interference that may cause undesired operation.
This equipment has been tested and found to comply with the limits for a Class
B digital device pursuant to part 15 of the FCC rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment on and
off, the user is encouraged to try to correct the interference by one or more
of the following measures:
-Reorient or relocate the receiving antennae
-Increase the separation between the equipment and the receiver
-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC RF Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. End users must follow the specific operating
instructions for satisfying RF exposure compliance. The antenna used for this
transmitter must not transmit simultaneously with any other antenna or
transmitter, except in accordance with FCC multi-transmitter product
procedures.
When equipped, the distance between antenna and one’s head surface is 40mm.
FCC Caution
Any changes or modifications to the equipment not expressly approved by the
party responsible for compliance could void user’s authority to operate the
equipment.
Industry Canada(IC) Statement
This device complies with Industry Canada license-exempt RSS standard(s).
Operation is subject to the following two conditions:
- this device may not cause interference, and
- this device must accept any interference, including interference that may cause undesired operation of the device.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>