ORDOCOM OB301 Outdoor CPE User Manual

ORDOCOM OB301 Outdoor CPE

Equipment Installation

This installation instruction takes 5.8G wireless bridge as an example

Product Installation

Use Environment Requirements

Topological Bridging

In wireless monitoring transmission, it is recommended to use the following diagram method for point-to-point or point-to-multipoint transmission. In point-to-mul tipoint transmission, please adjust the angle of the device.

Point-to-Multipoint

• Camera–Wireless Bridge
• Wireless Bridge–OVR—Monitoring Computer

Point-to-Point

• Camera—Switch–Wireless Bridge
• Wireless Bridge—OVR—Monitoring Computer

Bridging Method

Quick Setup
Bridge connection is divided into dialing bridge connection and digital display bridge connection, users can choose one of them according to their needs.

Dialing Bridge

1. Set Host- Client CPE
2. Select a bridge, turn the DIP switch to the main position (H) to set it as the host bridge. The dial switch of the other bridge is set to the sub-position (C), which is set as the client bridge.
3. Point-to-point one-click connection method
4. The host bridge and the client bridge press the Reset button for one second to initiate a connection.
5. Point-to-multipoint one-click connection method
6. The host bridge and multiple client bridges press the Reset button for one second to initiate a connection.
   Note : The button connection time between the host bridge and the client bridge needs to be synchronized completed within 1 minute.

Digital Bridge

1. Set Host CPE When two bridges need to be bridged, set one of the bridges as the host bridge first, press the button F to make H or C flash, then press the button S to modify it to H, wait for 5 seconds, and then the bridge will automatically save and restart.
2. Set Client CPE The other bridge is set as the client bridge, press the button F to make Hor C flash, then press the button S to modify it to C, wait for 5 seconds, the bridge will automatically save and restart.

Remarks

1. lt is in AP mode after the bridge is restored to factory settings, and its IP address is 192.168.188.253.
2. Button Fis the selection button, you can choose the host-client mode, channel, IP, signal value.
3. Button Sis the setting button, which can modify the host-client mode, channel, and IP.

Point-to-point one-click connection method

The host bridge and the client bridge, each press the Reset button for one second to initiate a connection.

Point-to-multipoint one-click connection method

The host bridge and multiple client bridges, by press the Reset button for one second to initiate a connection.

Note : The button connection time between the host bridge and the client bridge needs to be synchronized completed within 1 minute.

Channel Modification

In order to avoid interference, it is necessary to stagger the channels and only modify the host bridge channel, and the client bridge channel will automatically match the host bridge channel. Select the host bridge, select the channel by pressing the button F twice, and then press the button S to modify the channel value. After 5 seconds, the bridge will automatically save and restart.

IP Modification

To avoid the bridge IP conflict, modify the bridge IP, press the button F three times to select the IP flashing, and then press the button S to modify, wait for 5 seconds, and then the bridge will automatically save and restart.

Reset Method:
Please press and hold the Reset button for 10 seconds to reset the device.

WEB Setting

Wired Connection Computer Settings
Use wired connection method: The computer used for setting needs to set the IP address of the TCP/IP attribute of the wired network card to 192.168.188.X (X is 11-200), which is the same network segment as the CPE.

Log in to the Management Page

Use Google Chrome to visit http:l/192.168.188.253, the login page shown in the figure below pops up, and enter the login password: admin, to enter the home page.

Repeater Mode

In the Repeater mode, the point-to-point transparent transmission function is disabled by default. If you need to bridge the terminal device compatible with 4-address frame, please click the start button, as shown in the following figure:

• AP Mode In this mode, NAT, DHCP, firewall and all WAN-related functions will be disabled. All wireless interfaces and wired interfaces are bridged together, and there is no distinction between UXN and WAN.
• Configuration Method According to the quick setting wizard of each mode shown in the figure above, set the parameters and options required by the user, and click Next until the setting of each operation mode is completed.

Connection Status

1.Enter the repeater bridge and check the homepage. It is normal when the signal bar is green, and the signal value is generally between -70dBm and -40dBm.

Mobile Terminal WEB Login

CPE mobile phone login page, the login password: admin. WIFI login password: 66666666
After the mobile phone is connected to the CPE wirelessly, the static IP configuration is performea as follows:

1. Android (Android system) user mobile phone static IP setting method
   Open the mobile phone (Settings] , find and click (WLAN] to find and long press the WiFi name of the wireless router, and select (Static IP] from the pop-up menu to set the IP address 192.168.188.X on the same network segment as the CPE (X cannot be 253 or 252 ), gateway, netmask and domain name.

2. 10S (Apple system) user mobile phone static IP setting method
   Open the mobile phone (Settings] and select (WLAN] . After the connection is successful, click the exclamation mark to set the same network segment as 192.168.188.X (X cannot be 253 or 252), subnet mask, router and DNS.

Channel Table

Wireless Bridge Regional Channel Code Instructions

China

| 5.180GHz| Channel
5200GHz| Channel 40)
5.220GHz| Channel 44)
5.240GHz| (Channel
5.260GHz| (Channel 52)
5.280GHz| Channel 56)
5.300GHz| Channel 60)
5.320GHz| Channel 64)
5.745GHz| (Channel 149)
5.765GHz| Channel 153)
5.785GHz| Channel 157)
5.805GHz

5.825GHz

| Channel 161)

Channel 165)

America

| 5.180GHz| (Channel 36)
5.200GHz| Channel
5.220GHz| Channel
5.240GHz

5.260GHz

| Channel 48)

Channel 52)

5.280GHz| (Channel
5.300GHz

5.320GHz

5.500GHz

| Channel 60)

Channel 64)

(Channel 100)

5.520GHz| Channel 104)
5.540GHz| (Channel 108)
5.560GHz| Channel 112)
5.580GHz| Channel 116)
5.600GHz| Channel 120)
5.620GHz| Channel 124)
5.640GHz| Channel 128)
5.660GHz| Channel 132)
5.680GHz| Channel 136)
5.700GHz| (Channel 140)
5.745GHz| Channel 149)
5.765GHz| (Channel 153)
5.785GHz| Channel 157)
5.805GHz| Channel 161)
5.825GHz| Channel 165)
Regional Code| SG Channel
---|---

ETSI

| 5.180GHz| {Channel
5.200GHz| /Channel
5.220GHz| {Channel
5.240GHz| /Channel
5.260GHz| {Channel 52)
5.280GHz| /Channel 56)
5.300GHz| {Channel 60)
5.320GHz| (Channel
5.500GHz| /Channel 100)
5.520GHz| {Channel 104)
5.540GHz| /Channel 108)
5.560GHz| (Channel 112)
5.580GHz| {Channel 116)
5.600GHz

5.620GHz

| (Channel 120)

(Channel 124)

5.640GHz| {Channel 128)
5.660GHz| (Channel 132)
5.680GHz| {Channel 136)
5.700GHz| (Channel 140)
Regional Code| 2.4G Channel

China

| 2.412GHz| {Channel 1)
2.417GHz

2.422GHz

2.427GHz

2.432GHz

| /Channel 2)

{Channel 3)

{Channel 4)

/Channel 5)

2.437GHz| {Channel 6)
2.442GHz| {Channel 7)
2.447GHz| {Channel 8)
2.452GHz| {Channel 9)
2.457GHz| {Channel 10)
2.462GHz| {Channel 11)
2.467GHz| /Channel 12)
2.472GHz| {Channel 13)

America

| 2.412GHz| /Channel 1)
2.417GHz| {Channel 2)
2.422GHz| (Channel 3)
2.427GHz| {Channel 4)
2.432GHz| (Channel 5)
2.437GHz| {Channel 6)
2.442GHz| {Channel 7)
2.447GHz| {Channel 8)
2.452GHz| {Channel 9)
2.457GHz| /Channel 10)
2.462GHz| {Channel 11)

Common Faults and Solutions

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>