HILTI HIT-HY 200-A Adhesive Anchor Instruction Manual

: June 12, 2024
: HILTI

Table of Contents

HIT-HY 200-A Adhesive Anchor
Read User Manual Online (PDF format)
Download This Manual (PDF format)

qr.hilti.com/manual/?id=2042503

Hilti HIT-HY 200-A

HIT-HY 200-A Adhesive Anchor

Warning
Contains: hydroxypropylmethacrylate (A)
1,4-Butandiol-dimethacrylat (A) dibenzoyl peroxide (B) May cause an allergic skin reaction. (A, B)
Causes serious eye irritation. (B) Very toxic to aquatic life with long lasting effects. (B)
UFI: GW9R-EG2H-J71J-77TX (A) /
UFI: XGKR-1G37-6711-DD3D (B)

HILTI HIT-HY 200-A Adhesive Anchor - fig

1 Uncracked concrete;
2 Cracked concrete;
3 Dry concrete;
4 Water saturated concrete;
5 Waterfilled borehole in concrete;
6 Threaded rod, Threaded sleeve;
7 Rebar;
8 HAS-D;
9 HIT-Z, HIT-Z-R;
10 Hammer drilling;
11 Hollow drill bit;
12 Diamond coring;
13 Roughening tool;| 14 Temperature of concrete;
15 Working
time;
16 Curing time;
17 Roughening time;
18 Blowing time;
19 ECO mode;
20 Automatic filter cleaning
---|---

HILTI HIT-HY 200-A Adhesive Anchor - fig 2 HILTI
HIT-HY 200-A Adhesive Anchor - fig 10d

HILTI HIT-HY 200-A Adhesive Anchor - fig 3 HILTI
HIT-HY 200-A Adhesive Anchor - fig 5

Adhesive anchoring system for rebar and anchor fastenings in concrete.
HILTI HIT-HY 200-A Adhesive Anchor - fig 12 Hilti HIT-HY 200-A
Contains: Hydroxypropylmethacrylat (A), 1,4-Butandiol-dimethacrylat (A), Dibenzoylperoxid (B)
Warning May cause an allergic skin reaction. (A, B) | Causes serious eye irritation. (B) | Very toxic to aquatic life with long lasting effects. (B) | Do not get in eyes, on skin or on clothing. | Wear protective gloves/protective clothing/eye protection/ face protection. | IF ON SKIN: Wash with plenty of soap and water. | IF IN EYES: Rinse cautiously with water for several minutes. Remove contact lenses, if present and easy to do. Continue rinsing. | If skin irritation or rash occurs: Get medical advice/attention. | If eye irritation persists: Get medical advice/attention.
Disposal considerations: Empty packs: Leave the mixer attached and dispose of via the local Green Dot recovery system or EAK waste material code: 150102 plastic packaging Full or partially emptied packs: Must be disposed of as special waste in accordance with official regulations. EAK waste material code: 08 04 09 waste adhesives and sealants containing organic solvents or other dangerous substances. or EAK waste material code: 20 01 27 paint, inks, adhesives and resins containing dangerous substances.
Product Information: Always keep these instructions together with the product even when given to other persons. Material Safety Data Sheet: Review the MSDS before use. Check expiration date: See imprint on foil pack manifold (month/year). Do not use expired product. Foil pack temperature during usage: 0 °C to 40 °C / 32 °F to 104 °F. Base material temperature at time of installation: HAS-U, HAS-D, HIT-V, HIS, Rebar: between -10 °C and 40 °C / 14 °F and 104 °F.; HIT-Z: between +5°C and 40°C / 41°F and 104°F. Conditions for transport and storage: Keep in a cool, dry and dark place between 5 °C and 25 °C / 41 °F and 77 °F. For any application not covered by this document / beyond values specified, please contact Hilti. Partly used foil packs must remain in the cassette and has to be used within 4 weeks. Leave the mixer attached on the foil pack manifold and store within the cassette under the recommended storage conditions. If reused, attach a new mixer and discard the initial quantity of anchor adhesive.
Failure to observe these installation instructions, use of non-Hilti anchors, poor or questionable concrete conditions, or unique applications may affect the reliability or performance of the fastenings.
NOTICE
The surface of the HIT-Z / HAS-D anchor rod must not be altered in any way. Moreover, the thread of HIT-Z must stay free from dirt and dust during the installation procedure.
The HIT-Z cones must be fully embedded into mortar (especially at minimum embedment). Torque moment must always be applied on HIT-Z nut and washer installed above a solid baseplate laying on concrete.
Improper handling may cause mortar splashes. Always wear safety glasses, gloves and protective clothes during installation. | Never start dispensing without a mixer properly screwed on. | Attach a new mixer prior to dispensing a new foil pack (ensure snug fit). | Use only the type of mixer (HIT-RE-M) supplied with the adhesive. Do not modify the mixer in any way. | Never use damaged foil packs and/or damaged or unclean foil pack holders (cassettes).
Poor load values / potential failure of fastening points due to inadequate borehole cleaning. Hilti hollow drill bits TE-CD, TE-YD must be used in conjunction with a properly maintained Hilti vacuum cleaner with model and suction capacity (volumetric
flow rate) as specified in the accessory table. | The boreholes must be free of debris, dust, water, ice, oil, grease and other contaminants prior to adhesive injection. | For blowing out the borehole – blow out with oil free air until return air stream is free of noticeable dust. | For flushing the borehole – flush with water line pressure until water runs clear. | For brushing the borehole – only use specified wire brush. The brush must resist insertion into the borehole – if not the brush is too small and must be
replaced. | Important! Remove all water from the borehole and blow out with oil free compressed air until borehole is completely dried before mortar injection. | Do not exceed the roughening time when roughening the drilled hole!
Ensure that boreholes are filled from the back of the borehole without forming air voids. If necessary use the accessories / exten- sions to reach the back of the borehole. | For overhead applications use the overhead accessories HIT-SZ and take special care
when inserting the fastening element. Excess adhesive may be forced out of the borehole. Make sure that no mortar drips onto the installer. | In water saturated concrete it is required to set the anchor immediately after cleaning the borehole.
Not adhering to these setting instructions can result in failure of fastening points!

**** 21	21	21	21	21
Hilti AG	Hilti AG	Hilti AG	Hilti AG	Hilti AG
FL-9494 Schaan	FL-9494 Schaan	FL-9494 Schaan	FL-9494 Schaan	FL-9494 Schaan
Hilti Werke	Hilti Werke	Hilti Werke	Hilti Werke	Hilti Werke
2873-CPR-201-05	2873-CPR-201-10	2873-CPR-201-42	2873-CPR-201-16

Made in Germany
Hilti = registered trademark of Hilti Corporation, Schaan, Liechtenstein
www.hilti.group
© 2021 Right of technical changes reserved S.E. & O