RYOBI RML18 18V ONE Plus Magnifying Clamp Light Instruction Manual

June 12, 2024
RYOBI

RYOBI Logo

18V ONE Plus Magnifying Clamp Light
Instruction Manual

RYOBI RML18 18V ONE Plus Magnifying Clamp LightRML18

IMPORTANT!
It is essential that you read the instructions in this manual before assembling, operating, and maintaining the product. Subject to technical modifications.
Safety, performance, and dependability have been given top priority in the design of your magnifying clamp light.

INTENDED USE

The magnifying clamp light is intended for general illumination. The product can also be used as a magnifying glass with illumination for precision works. Do not use the product in wet conditions.
The product must be clamped during use.
The product is not intended for clamping on tubular materials.
When clamping, the material being clamped must be pushed to the deepest point of the clamp for increased stability.
Do not use the product for any other purpose. Use of the product for operations different from intended could result in a hazardous situation.

MAGNIFYING CLAMP LIGHT SAFETY WARNINGS

  • The light source contained in this luminaire shall only be replaced by the manufacturer or his service agent or a similar qualified person.
  • Use only with recommended battery pack and charger. Any attempt to use another battery pack will cause damage to the product and could possibly explode, cause a fire, or personal injury.
  • Do not disassemble the product.
  • If wrapped or in contact with fabrics, the lens can produce sufficient heat to melt some fabrics. To avoid serious personal injury, never allow the lens to come in contact with anything.
  • Do not place the product or battery pack near fire or heat. This will reduce the risk of explosion and possible injury.
  • Remove the battery pack or disconnect the mains power before starting any work on the product.
  • Do not store the product in a damp or wet location, or in a location where the temperature may reach or exceed 40°C. For example, inside sheds, vehicles, or metal buildings in the summer.
  • Do not direct the light beam at persons or animals and do not stare into the light beam yourself (not even from a distance). Staring into the light beam may result in serious injury or vision loss.

BATTERY SAFETY WARNINGS

  • To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.

TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and regulations.
Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.

MAINTENANCE

  • Use only original accessories and spare parts. Shouldcomponents need to be replaced which have not been described, please contact an authorised service centre. All repairs should be performed by an authorised service centre.
  • Avoid using solvents when cleaning plastic parts. Most plastics are susceptible to various types of commercial solvents and may be damaged by their use. Use clean cloths to remove dirt, carbon dust, etc.
  • Do not at any time let brake fluids, gasoline, petroleumbased products,  penetrating oils, etc.,come in contact  with plastic parts. Chemicals can damage, weaken or destroy plastic which may result in serious personalinjury.

SYMBOLS ON THE PRODUCT

| Volts
---|---
| Direct current
| The rated maximum ambient temperature
| Regulatory Compliance Mark (RCM). Product meets applicable regulatory requirements.
| Please read the instructions carefully before starting the machine.
| Class III protection

**** Do not dispose of waste batteries, waste electrical and electronic equipment as unsorted municipal waste.
Waste batteries and waste electrical and electronic equipment must be collected separately.
Waste batteries, waste accumulators, and light sources have to be removed from the equipment.
Check with your local authority or retailer for recycling advice and collection point.
According to local regulations, retailers may have an obligation to take back waste batteries and waste electrical and electronic equipment free of charge.
Your contribution to the reuse and recycling of waste batteries and waste electrical and electronic equipment helps to reduce the demand of raw materials.
Waste batteries, in particular containing lithium, and waste electrical and electronic equipment contain valuable and recyclable materials, which can adversely impact the environment and the human health if not disposed of in an environmentally compatible manner.
Delete personal data from waste equipment, if any.

SYMBOLS IN THIS MANUAL

| Safety Alert
---|---
****| Note
| Parts or accessories sold separately

RYOBI RML18 18V ONE Plus Magnifying Clamp Light - RYOBI RML18 18V ONE Plus
Magnifying Clamp Light - FigRYOBI RML18 18V ONE Plus Magnifying Clamp
Light - RYOBI RML18 18V ONE Plus Magnifying Clamp Light -
Fig1

PRODUCT SPECIFICATIONS

Magnifying LED clamp light

Model| RML18
Voltage| 18 V
Wattage| 6.8 W
Light output (Lumens)|
High brightness level| 500 Lum
Low brightness level| 200 Lum
Colour rendering index (CRI)| 80
Correlated colour temperature (CCT)| 6500 K
Weight – excluding battery pack| 0.6 kg

BATTERY

Compatible battery pack (not included)

RB18L13 RB18L25 RB18L60A RB1840X
RB18L15 RB18L25A RB18L90A RB1850C
RB18L15A RB18L40 RB1815C RB1850X
RB18L15B RB18L40A RB1820C RB1860X
RB18L20 RB18L50 RB1825C
RB18L20A RB18L50A RB1840C

Imported by:
Techtronic Industries Australia Pty Ltd
31 Gilby Road, Mount Waverley, VIC 3149
Melbourne, Australia
Techtronic Industries N.Z. Limited
Unit C, 70 Business Parade South,
Highbrook, Auckland 2013, New Zealand
RYOBI is a trade mark of Ryobi Limited, and is used under license.
20220802v1

Documents / Resources

| RYOBI RML18 18V ONE Plus Magnifying Clamp Light [pdf] Instruction Manual
RML18, RML18 18V ONE Plus Magnifying Clamp Light, 18V ONE Plus Magnifying Clamp Light, ONE Plus Magnifying Clamp Light, Magnifying Clamp Light, Clamp Light, Light
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals