Husqvarna LC 247 Lawn Mower Instruction Manual
- June 12, 2024
- Husqvarna
Table of Contents
Husqvarna LC 247 Lawn Mower
Product Information
Thank you for choosing a Husqvarna product. We are confident that you will be satisfied with the quality and performance of our product. Our products come with professional help and service for any repairs that may be needed. If the retailer who sold you the machine is not one of our authorized dealers, please ask for the address of your nearest service workshop.
We hope that you will enjoy your product for a long time. The operator’s manual provided with the machine is a valuable document that contains important information about usage, service, maintenance, and more. By following the manual’s instructions, you can extend the lifespan and second- hand value of the machine. If you decide to sell the machine, make sure to pass on the operator’s manual to the buyer.
Thank you for using a Husqvarna product. Please note that Husqvarna AB reserves the right to modify the design and appearance of products without prior notice as part of our continuous product development policy.
Product Usage Instructions
What is what on the lawn mower?
- 1. Engine brake handle
- 2. Propulsion bar (LC 247S, LC 247SP)
- 3. Catcher
- 4. Locking lever for handle height adjustment
- 5. Dipstick/oil filler
- 6. Cutting cover
- 7. Muffler
- 8. Spark plug
- 9. Starter handle
- 10. Back shield
- 11. Air filter
- 12. Refuelling
- 13. Cutting height control
- 14. Primer diaphragm (LC 247, LC 247S)
- 15. Operator’s manual
Cutting Cover
To check the cutting cover, visually inspect it for any damage or wear. If
there are any issues with the cutting cover, please contact your service agent
for repair or replacement.
Engine Brake Handle
To inspect the engine brake handle, follow these steps:
- Start the machine according to the starting instructions mentioned in the operator’s manual.
- Release the brake handle.
- The engine brake should always be adjusted so that the engine stops within 3 seconds. If it does not meet this requirement, contact your service agent for adjustment.
Muffler
WARNING: Never use a machine without a muffler, or with a faulty muffler. A damaged muffler may substantially increase the noise level and the fire hazard. Keep fire fighting equipment handy.
To inspect the muffler:
- The muffler gets very hot during and after use, including during idling. Be cautious of the fire hazard, especially when working near flammable substances and/or vapors.
- If you notice any damage or issues with the muffler, please contact your service agent for repair or replacement.
Assembling and Adjustments
Before assembling and adjusting your lawn mower, it is important to prevent unintentional starting by removing the ignition cable from the spark plug.
Handle:
- Make sure the handle is securely attached to both sides of the machine.
- There are different settings for operating position and transport position. Adjust the handle accordingly for your desired position.
Catcher:
When using the catcher, adjust the cutting height to your preference. Avoid
setting the cutting height too low as it may cause the cutters to hit the
ground with unevenness. Adjust the cutting height control to the front for a
higher cutting height.
Mulcher Insert – Accessories:
If you have a mulcher insert accessory, follow the instructions provided to install and use the mulch plug.
Rear Discharging:
For rear discharging, please refer to the operator’s manual for specific
instructions.
Fuel Handling – Fueling
WARNING: Running an engine in a confined or badly ventilated area can result in death due to asphyxiation or carbon monoxide poisoning. Always ensure proper ventilation when fueling your lawn mower.
Follow the fueling instructions provided in the operator’s manual for safe and correct fueling procedures.
Dear Customer,
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based
on a tradition that dates back to 1689, when the Swedish King Karl XI ordered
the construction of a factory on the banks of the Husqvarna River, for
production of muskets. The location was logical, since water power was
harnessed from the Huskvarna River to create the water-powered plant. During
the more than 300 years in existence, the Husqvarna factory has produced a lot
of different products, from wood stoves to modern kitchen appliances, sewing
machines, bicycles, motorcycles etc. In 1956, the first motor driven lawn
mowers appeared, followed by chain saws in 1959, and it is within this area
Husqvarna is working today.
Today Husqvarna is one of the leading manufacturers in the world of forest and
garden products, with quality as our highest priority. The business concept is
to develop, manufacture and market motor-driven products for forestry and
gardening, as well as for the building and construction industry. Husqvarna′s
aim is also to be at the front edge for ergonomics, usability, security and
environmental protection. That is the reason why we have developed many
different features to add to our products within these areas.
We are convinced that you will appreciate with great satisfaction the quality
and performance of our product for a very long time to come. The purchase of
one of our products gives you access to professional help with repairs and
service whenever this may be necessary. If the retailer who sells your machine
is not one of our authorised dealers, ask for the address of your nearest
service workshop.
It is our wish that you will be satisfied with your product and that it will be
your companion for a long time. Think of this operator′s manual as a valuable
document. By following its content (usage, service, maintenance, etc), the
life span and the second-hand value of the machine can be extended. If you
sell this machine, make sure that the operator′s manual is passed on to the
buyer.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore
reserves the right to modify the design and appearance of products without
prior notice.
PRESENTATION
What is what on the
lawn mower?
- Engine brake handle
- Propulsion bar (LC 247S, LC 247SP)
- Catcher
- Locking lever for handle height adjustment
- Dipstick/oil filler
- Cutting cover
- Muffler
- Spark plug
- Starter handle
- Back shield
- Air filter
- Refuelling
- Cutting height control
- Primer diaphragm (LC 247, LC 247S)
- Operator′s manual
MACHINE´S SAFETY EQUIPMENT
General
This section describes the machine´s safety equipment, its purpose, and how
checks and maintenance should be carried out to ensure that it operates
correctly.
WARNING! Never use a machine that has faulty safety equipment! If your machine
fails any checks contact your service agent to get it repaired.
Do not modify this product or use it if it appears to have been modified by
others. Prevent unintentional starting by removing the ignition cable from the
spark plug.
Cutting cover
- The cutting cover is designed to reduce vibration and to reduce the risk of cuts.
Checking the cutting cover
- Make sure the cutting cover is not damaged and that there are no visible defects such as cracks in the protective outer cutting cover.
Engine brake handle
- The engine brake is designed to stop the engine. When the grip on the engine brake handle is released the engine should stop.
Inspecting the engine brake handle
Start the machine according to the starting instructions, see “Starting and
Stopping”, and then release the brake handle. The engine brake should always
be adjusted so that the engine stops within 3 seconds.
Muffler
WARNING! Never use a machine without a muffler, or with a faulty muffler. A
damaged muffler may substantially increase the noise level and the fire hazard.
Keep fire fighting equipment handy.
The muffler gets very hot during and after use. This also applies during
idling. Be aware of the fire hazard, especially when working near flammable
substances and/or vapours.
- The muffler is designed to keep noise levels to a minimum and to direct exhaust fumes away from the user.
Inspecting the muffler
- Check regularly that the muffler is complete and secured correctly.
ASSEMBLING AND ADJUSTMENTS
General
IMPORTANT! Prevent unintentional starting by removing the ignition cable from
the spark plug.
Handle
Settings
Handle height
- Loosen the lower knobs.
- Slide the knobs to the ends of the grooves on both sides of the machine.
Handle height can be set to 2 different positions,- Adjust to a suitable height.
- Slide the knobs up towards the handle until they stop and a click is heard.
- Tighten the knobs properly.
Transport position
The handle assembly can be folded to minimize space needed for transport
and storage.
- Loosen the lower knobs.
- Slide the knobs to the ends of the grooves on both sides of the machine.
- Fold in the engine brake handle towards the
handlebar. 
- Fold forward the handle.
Operating position
- Fold in the engine brake handle towards the handlebar.
- Fold the handle to its upright position.
- Slide the knobs up towards the handle until they stop and a click is heard.
- Screw on the handle with the knob.
Cutting height
- NOTICE! Do not set the cutting height too low as there is a risk that the cutters might hit ground with unevenness.
The machine is equipped with central cutting height adjustment.
- Move the lever to the back for lower cutting height and to the front for higher cutting height.
- The cutting height can be adjusted to 6 different positions with the cutting height lever.
Catcher
- The collector’s handle situated on the frame must be placed over the collector bag.
- Fasten the lower part of the frame in the groove underneath the collector.
- Secure the frame by using the quick-action clips.
- Make sure the machine’s discharge deck is clean and free from grass cuttings.
- Hook the collector onto the top edge of the chassis.
- Place the collector tongue in the machine’s discharge deck.
- Fit the bagger bottom in the discharge hole.
Mulcher insert – Accessories
A mulching-kit is available as an accessory, to make the machines equipped
with a catcher able to be used with mulching function. The kit contains of a
mulch plug and a blade.
- Raise the discharge guard to mount / dismount the mulch plug.
- Replace the blade with the supplied Combi blade. For more information, see ”Cutting equipment”.
Rear discharging
The machine can also be used without the mulcher insert and collector.
- Lift up the back shield and remove the catcher.
- Remove the mulch plug.
- Close the shield.
FUEL HANDLING
General
- WARNING! Running an engine in a confined or badly ventilated area can result in death due to asphyxiation or carbon monoxide poisoning.
Fuel and fuel fumes are highly inflammable and can cause serious injury when inhaled or allowed to come in contact with the skin. For this reason observe caution when handling fuel and make sure there is adequate ventilation.
The exhaust fumes from the engine are hot and may contain sparks which can start a fire. Never start the machine indoors or near combustible material!
Do not smoke and do not place any hot objects in the vicinity of fuel.
Fuel
NOTICE! The machine is equipped with a four-stroke engine. Make sure that
there is always sufficient oil in the oil tank.
Petrol
- Use good quality unleaded or leaded petrol.
- The lowest octane recommended is 90 (RON). If you run the engine on a lower octane grade than 90 so-called knocking can occur. This gives rise to a high engine temperature, which can result in serious engine damage.
- Use low-emission petrol, also known as alkylate petrol, if it is available.
Engine oil
NOTICE! Check the oil level before starting the lawn mower. A too low
oil level can cause serious damage to the engine. See instructions in the
section “Maintenance”.
- The engine oil should be changed the first time after 5 hours running time. Refer to Technical Data for recommendations on which oil type to use. Never use oil intended for two-stroke engines.
Fueling
- WARNING! Always stop the engine and let it cool for a few minutes before refuelling.
Use a petrol can at all times to avoid spillage.
When refuelling, open the fuel cap slowly so that any excess pressure is released gently.
Clean the area around the fuel cap.
Tighten the fuel cap carefully after refuelling. Negligence may lead to the start of a fire.
Move the machine at least 3 m from the refuelling point before starting it.
Never start the machine:
- If you have spilled fuel or engine oil on the machine. Wipe off the spill and allow the remaining fuel to evaporate.
- If you have spilled fuel on yourself or your clothes, change your clothes. Wash any part of your body that has come in contact with fuel. Use soap and water.
- If the machine is leaking fuel. Check regularly for leaks from the fuel cap and fuel lines.
Transport and storage
- Store and transport the machine and fuel so that there is no risk of any leakage or fumes coming into contact with sparks or open flames, for example, from electrical machinery, electric motors, electrical relays/switches or boilers.
- When storing and transporting fuel always use approved containers intended for this purpose.
Long-term storage
- When storing the machine for long periods the fuel tank must be emptied. Contact your local petrol station to find out where to dispose of excess fuel.
OPERATING
Personal protective equipment
You must use approved personal protective equipment whenever you use the
machine. Personal protective equipment cannot eliminate the risk of injury but
it will reduce the degree of injury if an accident does happen. Ask your
dealer for help in choosing the right equipment.
Always wear:
- Use ear muffs if the noise level exceeds 85 db.
- Sturdy, non-slip boots or shoes.
- Heavy, long pants. Do not wear shorts, sandals or go barefoot.
- Gloves must be worn when required, for example when fitting, inspecting or cleaning cutting attachments.
General safety precautions
This section describes basic safety directions for using the machine. This
information is never a substitute for professional skills and experience.
- Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
- Keep in mind that the operator is responsible for accidents or hazards occurring to other people or their property.
- The machine must be kept clean. Signs and stickers must be fully legible.
Always use common sense
It is not possible to cover every conceivable situation you can face. Always
exercise care and use your common sense. If you get into a situation where you
feel unsafe, stop and seek expert advice. Contact your dealer, service agent
or an experienced user. Do not attempt any task that you feel unsure of!
WARNING! This machine produces an electromagnetic field during operation. This field may under some circumstances interfere with active or passive medical implants. To reduce the risk of serious or fatal injury, we recommend persons with medical implants to consult their physician and the medical implant manufacturer before operating this machine.
WARNING! The machine can be a dangerous tool if used incorrectly or
carelessly, which can cause serious or fatal injury to the operator or others.
Never allow children or other persons not trained in the use of the machine to
use or service it.
The machine should not be used by people with reduced physical or mental
capacities or people who are unsuitable for health reasons to operate the
machine, without supervision of a person responsible for their safety.
Never allow anyone else to use the machine without first ensuring that they
have read and understood the contents of the operator’s manual.
Never use the machine if you are fatigued, while under the influence of alcohol
or drugs, medication or anything that could affect your vision, alertness,
coordination or judgement.
WARNING! Unauthorized modifications and/or accessories may lead to serious
injury or death to the user or others. Under no circumstances may the design
of the machine be modified without the permission of the manufacturer.
Do not modify this product or use it if it appears to have been modified by
others.
Never use a machine that is faulty. Carry out the checks, maintenance and
service instructions described in this manual. Some maintenance and service
measures must be carried out by trained and qualified specialists.
Always use genuine accessories.
Work area safety
- Branches, twigs, stones, etc. should be removed from the lawn before you start to mow.
- Objects hitting against the cutting attachment could be thrown and cause damage to people and objects. Keep people and animals well away.
- Never use the machine in bad weather, for instance in fog, in rain, damp or in wet locations,strong winds, intense cold, risk of lightning, etc. Working in bad weather is tiring and can lead to dangerous conditions, e.g. slippery surfaces.
- Observe your surroundings to ensure that nothing can affect your control of the machine.
- Beware of roots, stones, twigs, pits, ditches etc. Tall grass can hide obstacles.
- Mowing slopes can be dangerous. Do not use the lawn mower on very steep slopes. The lawn mower should not be used on inclines greater than 15 degrees.
- On sloping ground you should work along the slope. It is much easier to work along a slope than it is to work up and down it.
- Be careful when you are approaching hidden corners and objects that could block your view.
Work safety
- A lawn mower is only designed to mow lawns. All other use is forbidden.
- Wear personal protective equipment. See instructions under the ”Personal protective equipment” heading.
- Do not start a lawn mower unless the cutter and all covers are fitted correctly. Otherwise the cutter could come loose and cause personal injuries.
- Make sure the cutter does not hit foreign objects such as stones, roots or the like. This can make the cutter dull and bend the engine shaft. A bent axle gives imbalance and heavy vibration, which results in a great risk of the cutter becoming loose.
- The brake handle must never be permanently anchored in handle when the machine is running.
- Place the lawn mower on firm, flat surface and start it. Make sure that the cutter cannot come into contact with the ground or other objects.
- Always place yourself behind the machine. Allow all the wheels to remain on the ground and keep both hands on the handle when mowing. Keep your hands and feet away from the rotating blades.
- Do not tilt the machine when the engine is running.
- Pay particular attention when pulling the machine towards you during work.
- Never lift up the lawn mower or carry it around when the engine is running. If you must lift the lawn mower, first switch off the engine and disconnect the ignition lead from the spark plug.
- Do not mow the lawn while walking backwards.
- The engine should be switched off when moving over ground that is not to be mowed. For example, gravel paths, stone, shingle, asphalt, etc.
- Never run with the machine when it is running. You should always walk with the lawn mower.
- Shut down the engine before changing the cutting height. Never make adjustments with the engine running.
- Never leave the machine unsupervised with the motor running. Turn off the motor. Ensure the cutting attachment has stopped rotating.
- If any foreign object is hit or if vibrations occur stop the machine immediately. Disconnect the HT lead from the spark plug. Check that the machine is not damaged. Repair any damage.
Basic working techniques
- Always cut with a sharp blade for optimal results. A dull blade gives an uneven cut and the grass becomes yellow on the surface of the cut.
- Never mow more than 1/3 of the length of the grass. This especially applies during dry periods. Mow first with the cutting height set high. Then check the result and lower to an appropriate height. If the grass is really long, drive slowly and mow twice if necessary.
- Cut in different directions each time in order to avoid stripes in the lawn.
Transport and storage
- Secure the equipment during transportation in order to avoid transport damage and accidents.
- Store the equipment in a lockable area so that it is out of reach of children and unauthorized persons.
- Store the machine and its equipment in a dry and frost proof place.
- For transport and storage of fuel, see the section”Fuel handling”.
Starting and stopping
Before starting
WARNING! Please read the operator’s manual carefully and make sure you
understand the instructions before using the machine.
Wear personal protective equipment. See instructions under the ”Personal
protective equipment” heading.
- Keep people and animals well away from the working area.
- Perform daily maintenance. See instructions in the section “Maintenance”.
- Ensure the ignition lead sits correctly on the spark plug.
Starting
Models LC 247, LC 247S have manual choke (primer diaphragm). If the lawn mower
is being started for the first time press on the fuel pump five times. After
that you should press on the fuel pump three times when starting a cold
engine.
-
The engine brake handle must be held against the handlebar when the engine is started.
-
Position yourself behind the machine.
-
Grip the starter handle, slowly pull out the cord with your right hand until you feel some resistance (the starter pawls grip). Pull with force to start the engine. Never twist the starter cord around your hand.
Drive (LC 247S, LC 247SP) -
Push the propulsion bar in towards the handle in order to start the drive.
-
-
Before pulling the machine towards you, disengage the drive and push the machine forward approx. 10 cm.
Stopping
- Stop the engine by releasing the engine brake handle.
MAINTENANCE
General
- WARNING! The user must only carry out the maintenance and service work described in this Operator’s Manual. More extensive work must be carried out by a service workshop.
Switch off the engine before carrying out any checks or maintenance. Prevent unintentional starting by removing the ignition cable from the spark plug.
The life span of the machine can be reduced and the risk of accidents can increase if machine maintenance is not carried out correctly and if service and/or repairs are not carried out professionally. If you need further information please contact your nearest service workshop.
CAUTION! When the machine is tilted, make sure the air filter always is placed in the highest position.
- Always use genuine accessories.
Maintenance schedule
In the maintenance schedule you can see which parts of your machine that
require maintenance, and with which intervals it should take place. The
intervals are calculated based on daily use of the machine, and may differ
depending on the rate of usage.
| Before starting | Weekly maintenance | Monthly maintenance |
|---|---|---|
| General inspection | Spark plug | Air filter |
| External cleaning | Muffler* | Fuel system |
| Oil level | ||
| Cutting equipment | ||
| Cutting cover* | ||
| Inspecting and adjusting the drive belt | ||
| Engine brake handle* |
*See instructions in the section “Machine’s safety equipment”.
Please see the engine Operator’s Manual for additional information about
servicing the engine.
General inspection
- Check that nuts and screws are tight.
External cleaning
- Brush leaves, grass and the like off of the lawn mower.
- Do not use a high pressure washer to clean the machine.
- Never flush water directly on the engine.
- Clean the air intake on the starter. Check the starter and starter cord.
- When cleaning under the cutting deck, turn the machine with the spark plug upwards. Empty the fuel tank.
Oil level
IMPORTANT! Allow the machine to cool. Hot oil can cause severe burn injuries.
The lawn mower should stand on flat ground when you check the oil level. Check the oil level with the dipstick on the oil filler cap.
- Remove the oil cap and wipe the dipstick clean.
- Put the dipstick back in.
- If the oil level is low, fill using engine oil up to the upper level on the dipstick.
Cutting equipment
- Check the cutting attachment for damage or cracks. A damaged cutting attachment should always be replaced.
- Always ensure the cutter is well ground and balanced correctly.
CAUTION! The blades should be balanced after sharpening. Balancing,
replacing or sharpening the blades should be conducted by a service workshop.
Damaged blades should be replaced when hitting obstacles that result in a
breakdown. Let the service centre assess whether the blade can be sharpened or
must be replaced.
Dismantling
WARNING! Prevent unintentional starting by removing the ignition cable from
the spark plug.
- Lock the blade with a wooden block. Loosen the blade bolt and remove the blade bolt, the washer and the blade. Remove the blade bolt by turn the bolt counter-clockwise.
- Make sure the blade bracket is free of damage. Also check that the cutter bolt is undamaged and that the engine shaft is not bent.
Assembly
- The blade must be mounted with the angled ends pointing up towards the cover.
Place the cutter with the friction washer against the cutter bracket. Make sure the cutter centres correctly on the shaft. 
- Lock the blade with a wooden block. Fit the washer and tighten the bolt correctly by turning clockwise. The bolt should be tightened with a torque of 70 Nm.
- Pull the blade around by hand and make sure it rotates freely.
- Test run the machine.
IMPORTANT!
Always exercise care and use your common sense. Avoid all situations which you
consider to be beyond your capability. If you still feel uncertain about
operating procedures after reading these instructions, you should consult an
expert before continuing. Contact an authorised service workshop.
Always use genuine parts. For more information, see the ”Technical data”
section.
Spark plug
NOTICE! Always use the recommended spark plug type! Use of the wrong spark
plug can damage the piston/cylinder.
- If the machine is low on power, difficult to start or runs poorly at idle speed: always check the spark plug first before taking other steps.
- If the spark plug is dirty, clean it and check that the electrode gap is 0.7 mm. Replace if necessary.
Adjusting the drive belt
If the drive feels slow, it may be due to a slipping belt and the clutch cable
will then have to be adjusted.
Finely adjust the wire using the adjuster screw. 
-
To tension the wire and increase speed, screw the adjustment screw counterclockwise.
Make sure the wires are not tensioned too tight. If the lawn mower starts to drive withtout the clutch lever is beeing operated, extend the wire. -
To extend the wire and reduce speed, screw the adjustment screw clockwise.
If the drive still feels slow, the belt will have to be replaced. Contact an authorised service workshop.
Air filter
- Remove the air filter cover and take out the filter.
- An air filter that has been in use for a long time cannot be cleaned completely. The filter must therefore be replaced with a new one at regular intervals. A damaged air filter must always be replaced.
- When reassembling, make sure that the filter completely seals against the filter holder.
Clean the paper filter (LC 247SP)
- Clean the filter by knocking the filter against a flat surface. Never use solvent with petroleum, for example, kerosene, or compressed air to clean the filter.
Cleaning the foam plastic filter (LC 247, LC 247S)
- Remove the foam plastic filter. Wash the filter well in tepid soapy water. After cleaning, rinse the filter well in clean water. Squeeze out and allow the filter to dry.
NOTE! High pressure compressed air can damage the foam. After cleaning the filter should be oiled using engine oil. Wipe away excess oil by pressing a clean cloth against the filter.
Oil change
IMPORTANT! Allow the machine to cool. Hot oil can cause severe burn injuries.
- Empty the fuel tank.
- Unscrew the oil filler cap.
- Place a suitable vessel to collect the oil in.
- Drain the oil by tipping the engine so that the oil runs out through the filler pipe. When the machine is tilted, make sure the air filter always is placed in the highest position. Ask where you can dispose of surplus engine oil at your local petrol station.
- Fill with new engine oil of the right quality. See instructions in the section “Technical data”.
- Please see the engine Operator’s Manual for more information.
Fuel system
- Check that the fuel cap and its seal are not damaged.
- Check the fuel hose. Replace if necessary.
Technical data
| LC 247 | LC 247S | LC 247SP |
|---|
Engine
Engine manufacturer| Briggs & Stratton| Briggs & Stratton| Briggs & Stratton
Cylinder displacement, cm3| 125| 125| 140
Speed, rpm| 2900| 2900| 2900
Nominal engine output, kW (see note 1)| 1,8@2900| 1,8@2900| 2,1@2900
Ignition system
Spark plug| Champion XC92YC| Champion XC92YC| Champion XC92YC
Electrode gap, mm| 0,5| 0,5| 0,5
Fuel and lubrication system
Fuel tank capacity, litre| 0,8| 0,8| 0,8
*Engine oil| SAE 30/SAE 10W-30| SAE 30/SAE 10W-30| SAE 30/SAE 10W-30
Weight
Machine with empty tanks, kg| 27| 29| 29
Noise emissions (see note 2)
Sound power level, measured dB (A)| 95,7| 95,7| 94,4
Sound power level, guaranteed LWA dB (A)| 96| 96| 96
Sound levels (see note 3)
Sound pressure level at the operators ear, dB(A)| 84,8| 84,8| 84,1
Vibration levels, a hveq (see note 4)
Handle, m/s2| 3,4| 3,4| 3,4
Cutting system
Cutting height, mm| 20-75| 20-75| 20-75
Cutting width, cm| 47| 47| 47
Cutter| Collect| Collect| Collect
Article number| 5882755-10| 5882755-10| 5882755-10
Bagger capacity, litre| 55| 55| 55
Note 1: The power rating of the engine indicated is the average net
output (at specified rpm) of a typical production engine for the engine model
measured to SAE standard J1349/ISO1585. Mass production engines may differ
from this value. Actual power output for the engine installed on the final
machine will depend on the operating speed, environmental conditions and other
values.
Note 2: Noise emissions in the environment measured as sound power (LWA)
in conformity with EC directive 2000/14/EC.
Note 3: Noise pressure level according to ISO 5395. Reported data for
noise pressure level has a typical statistical dispersion (standard deviation)
of 1.2 dB(A).
Note 4: Vibration level according to ISO 5395. Reported data for
vibration level has a typical statistical dispersion (standard deviation) of
0.2 m/s2.
*Use engine oil of quality SF, SG, SH, SJ or higher. See the viscosity chart in the engine manufacturer’s manual and select the best viscosity based on the expected outside temperature.
EC Declaration of Conformity
(Applies to Europe only)
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel.: +46-36-146500, hereby
declares that the lawn mower Husqvarna LC 247, LC 247S, LC247 SP, starting
with serial number 15XXXXXXX and onwards, complies with the requirements of
the COUNCIL’S DIRECTIVE:
- of May 17, 2006 ”relating to machinery” 2006/42/EC.
- of February 26, 2014 ”relating to electromagnetic compatibility” 2014/30/EU.
- of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. For information relating to noise emissions, see the Technical data chapter.
The following standards have been applied: ISO 5395, ISO 14982
Notified body: 0404, SMP Svensk Maskinprovning AB, Box 7035, SE-750 07 Uppsala,
has issued reports regarding the assessment of conformity according to annex
VI of the COUNCIL’S DIRECTIVE of May 8, 2000 ”relating to the noise emissions
in the environment” 2000/14/EC.
Huskvarna 25 November 2015
Claes Losdal, Development Manager/Garden Products
(Authorized representative for Husqvarna AB and responsible for technical
documentation.)
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>