milwaukee L4BOLTHL Rechargeable LED BOLT Headlamp Instruction Manual

: June 12, 2024
: Milwaukee

Table of Contents

OPERATING INSTRUCTIONS
TECHNICAL DATA
SAFETY INSTRUCTIONS BATTERY-LAMP
SAFETY INSTRUCTIONS BATTERY
SPECIFIED CONDITIONS OF USE
CHARGING
FUEL GAUGE
NOTES FOR LI-ION BATTERIES
MAINTENANCE
SYMBOLS
CUSTOMER SUPPORT
Documents / Resources

milwaukee L4BOLTHL Rechargeable LED BOLT Headlamp

milwaukee L4BOLTHL Rechargeable LED BOLT Headlamp

OPERATING INSTRUCTIONS

Operating Instructions

MODE memory: the selected operating mode is available again when switching on again.

TECHNICAL DATA

TECHNICAL DATA	L4 BOLTHL
Type	Battery-Lamp
Rated power output	5,5 W
Battery voltage	4 V
USB input	5 V DC, 0,1 A – 2,1 A
Charging time (3.0 A)	125 min

WARNING! Read all safety warnings and all instructions. Failure to follow the warnings and instructions may result in electric shock, fire and/or serious injury.

Save all warnings and instructions for future reference.

SAFETY INSTRUCTIONS BATTERY-LAMP

WARNING: Use only the recommended USB cable and charger.

Warning: Do not direct the light beam at persons or animals and do not stare into the light beam yourself (not even from a distance). Staring into the light beam may result in serious injury or vision loss.

The light source of this luminaire is not replaceable; when the light source reaches its end of life the whole luminaire shall be replaced.

SAFETY INSTRUCTIONS BATTERY

Only use Milwaukee Type L4B… rechargeable batteries.

Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it off immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately seek medical attention.

Warning! To reduce the risk of fire, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE

The battery lamp can be used as lighting independently of a mains power supply.

It is intended to be used with Milwaukee BOLT™ Hard Hats and Helmets.

Do not use this product in any other way as stated for normal use.

CHARGING

Plug the USB cable into a power source such as an AC wall adaptor, computer, or car port.
Lift the rubber cover to expose the USB Type C port. Insert the USB Type C plug into the USB Type C port. Users may experience longer charge times from laptops and other power sources.
NOTE: Always close the USB cover when light is not charging to maintain dust and moisture protection.
The indicator light ring around the power button will display the charging status:
Red pulsing: charging, 0-49% charged
Yellow pulsing: charging, 50-99% charged
Green solid: 100% charged
If the indicator light ring flashes red and green, check that the battery is fully seated into the bay. Remove the battery and reinsert.
If the light continues to flash red and green, the battery may be extremely hot or cold, or wet. Allow the battery to cool down, warm up, or dry out and then reinsert. If the problem persists, contact a MILWAUKEE service facility

FUEL GAUGE

The indicator light ring around the power button will display the battery life:

Red flashing: 0-3% remaining
Red solid: 4-10% remaining
Yellow solid: 11-49% remaining
Green solid: 50-100% remaining

NOTES FOR LI-ION BATTERIES

Use of Li-Ion batteries

Batteries which have not been used for some time should be recharged before use.

Temperatures in excess of 50°C (122°F) reduce the performance of the battery. Avoid extended exposure to heat or sunshine (risk of overheating).

The contacts of chargers and batteries must be kept clean.

For an optimum life-time, the batteries have to be fully charged, after used.

To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged. For battery storage longer than 30 days:

Store the battery where the temperature is below 27°C and away from moisture

Store the battery in a 30% – 50% charged condition Every six months of storage, charge the battery as normal.

Transport of Li-Ion batteries

Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.

Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.

The user can transport the batteries by road without further requirements.
Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.

When transporting batteries:

Ensure that battery contact terminals are protected and insulated to prevent short circuit.
Ensure that battery pack is secured against movement within packaging.
Do not transport batteries that are cracked or leak.

Check with forwarding company for further advice

MAINTENANCE

Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).

If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit No. on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max‑Eyth‑Straße 10, 71364 Winnenden, Germany.

SYMBOLS

Please read the instructions carefully before starting the machine.

CAUTION! WARNING! DANGER!)

Warning! Hot Surface! Do not touch!

Do not stare at the operating light source.)

USB Port

Class III electrical protection.

This tool is only suitable for indoor use. Never expose tool to rain.

Accessory – Not included in standard equipment, available as an accessory

Do not dispose of waste batteries, waste electrical and electronic equipment as unsorted municipal waste. Waste batteries and waste electrical and electronic equipment must be collected separately.
Waste batteries, waste accumulators and light sources have to be removed from equipment.
Check with your local authority or retailer for recycling advice and collection point.
According to local regulations retailers may have an obligation to take back waste batteries and Waste electrical and electronic equipment free of charge. Your contribution to re-use and recycling of waste batteries and waste electrical and electronic equipment helps to reduce the demand of raw materials.
Waste batteries, in particular containing lithium and waste Electrical and electronic equipment contain valuable, recyclable materials, which can adversely impact the environment and the human health, if not disposed of in an environmentally compatible manner.
Delete personal data from waste equipment, if any

European Conformity Mark

UK Conformity Mark

Ukraine Conformity Mark

EurAsian Conformity Mark

CUSTOMER SUPPORT

Techtronic Industries GmbH
Max-Eyth-Str. 10
71364 Winnenden
Germany

+49 (0) 7195-12-0

www.milwaukeetool.eu

Techtronic Industries (UK) Ltd
Parkway
Marlow SL7 1YL
UK

(12.22)
4931 4707 29

Documents / Resources

| milwaukee L4BOLTHL Rechargeable LED BOLT Headlamp [pdf] Instruction Manual
L4BOLTHL Rechargeable LED BOLT Headlamp, L4BOLTHL, Rechargeable LED BOLT Headlamp, LED BOLT Headlamp, BOLT Headlamp, Headlamp
---|---