INTUSONIC 6FP100 Multi-Purpose Speaker System User Manual

INTUSONIC 6FP100 Multi-Purpose Speaker System User Manual

  Welcome

Thank you for choosing INTUSONIC for your sound system. To make sure that this product meets your expectations and provides long-term, reliable performance, please read and follow this instruction manual carefully

Important safety instructions

• Read these instructions and all markings on the Keep these instructions.
• Heed all warnings and instructions, both in this manual and on the
• Clean only witha dry cloth.Unplug   the unit or   its   poweradaptor/charger from AC supply before cleaning.
• Do not use this product near water and avoid any exposure to
• Before connecting this product to any AC supply (if any), make sure to check whether the AC mains voltage and frequency match the indication on the product and its
• Only connect thisproduct or itspower adaptor/charger to an AC supply (if any) with sufficient power handling, protective earth connection,   ground-fault   (earth-fault)    protection protection.
•  Make sure any heat sink or other cooling surface, or any air convection slot, is exposed sufficiently to free air circulation and is not blocked.
• Do not operate this product in environmental temperatures exceeding 35 degrees Celsius and/or 85% relative humidity.
• Position the product in a safe and stable place for operation, out of reach of unauthorized persons.
• Make sure any cable connections to and from the product are neither subject to potentially destructive mechanical impact nor present any risk of stumbling or other accident risk to people.
• Audio equipment may generate sound pressure levels sufficient to cause permanent hearing damage to persons. Always start up at low volume settings and avoid prolonged exposure to sound pressure levels exceeding 90dB.
• Do not open this product for service purposes. There are no user-serviceable parts inside.
• Warranty will be void in any case of unauthorized service by the user or other not authorized persons.
• Take any precaution required by local law, applicable regulations or good business practice to avoid injury of people or material damage by use of this product.

Health Advice

This unit may produce and absorb electromagnetic radiation. The strength of radiation and the sensitivity for disturbing interference matches the CE and FCC requirements. A corresponding sign is printed on the backside of the unit. Any change or modification may affect the behavior of the unit concerning electromagnetic radiation, with the CE and FCC requirementeventually not to be responsibility in this case. met   any   more.   The   manufacturer   takes no

Functional Advice (only for powered products)

This unit is immune to the presence of electromagnetic disturbances – both conducted and radiated – up to a certain level. Under peak conditions, the unit is classified to show a “class C”performance criteria and mayencounter temporary degradation or loss of function which may need manual help to recover. In such case, switch the unit off and back on to recover.

Environmental Advice

This unit is built to conform to the ROHS-2 standard according to directive 2011/65/EU and the
WEEE directive 2012/19/EU of the European Parliament and of th
Council of the European Union. Under these regulations, the product shall not be discarded into regular garbage at the end of its life, but shall be returned to authorized recycling stations

Battery Advice (only for battery-powered products)

• Some products may contain a battery. Refer to the further chapters of this manual to determine whether this product contains a battery, and whether this is removable and/or rechargeable.
• Where applicable, adhere to the relative regulations in aviation
• If the battery is rechargeable, the battery might not be fully charged or partly discharged at the time of Recharge before use. Only use recommended or included chargers voltage/current rating.

Wireless Advice

• Some products may contain a wireless transmitter, receiver or transceiver. Refer to the further chapters of this manual to determine whether this product contains a frequency this operates. wireless function, and in which ote: When the transformer is installed the two parallel Speakon™-
• Make sure the frequency of operation does not require a specific license in the territory you operate the product in. If it does, obtain such license prior to anycompatible connectors will be disabled, and low imp via the 5.08mm terminal strip is disabled as well.dance operation
• Certain wireless technologies are designed for short distance operation. The actual distance will depend on how jammed the

Unpacking

Please check that the box contains the following items:

• 1 main unit
• 1 plug-in terminal block 4-pole P=5.08mm
• 2 M6 safety lug
• 1 M10 safety lug
• 1 instruction manual

If any part is missing, please contact your dealer immediately for replacement.

About this product

The    6FP100T     is    amulti-purposepassive    2-waylow-impedanceloudsp aker system for commercial applications. Due to its compact size
owed to the 6.5’’ woofer, it fits into most background music systems, but due to its powerful high frequency compression driver and horn, it can play
louder than many background music seakers. This mkes it a perfect choice mounti for multi-purpose venues. By g options, it can be: means of its extremely flexible

• Flown by the use of the M6 and M10 lug mounting points;
• Wall or ceiling mounted with any 75mm VESA compatible mount;
• Suspended down-facing from its pendant speaker;M10 lug mounting point as a
• Be directly attached to trussing or other tubes via a coupler attached to its M10 lug mounting

The 6FP100T can further be retrofitted with a 100V line transformer kit (Ref. UTK60) for the use in 100V line systems.

Structural Design

Note: his speaker isupposed to be operated with thhigh frequency extensive experience, like calculating working load limits, knowledge

1. OWooden Lama I nis is the main body at the speaker. uue to the wooden base material, this speaker is only suitable for indoor use
2. Grille. This metal mesh grille protects the drivers from mechanical impact and also from dust by the inner foam layer. Keep the grille 1
3. „gmated unless rotation of the HF hom is required during installation. 0 LF Driver (woofer). This is 6.5″ / 8 Ohm low/mid frequency loudspeaker. HF Driver (compression driver & horn).
4. This is 9, 1″ voice coil compression driver mounted to a 90°x60° horn. The horn can be turned for horizontal mounting (refer to the chapter below). O M10 mounting point This is a rear-welded dosed M10 thread insert which can be used for both lug mounting and coupler mounting.
5. Make sure the inserted screw’s thread length is longer than 10mm and shorter than 16mm. M4 VESA mounting point These are 4 points of M4 threaded holes pre/fitted M4x10 screws. Do not remove the screws even if no VESA mount is fitted, as the screw holes need to be closed for air sealing purposes. Only use supplied screws for VESA mounting, do not use longer screws to avoid damage to the speaker structure.

Configuration

The 6FP100T can be installed vertically or horizontally. Wherever possible, vertical installation is recommended. Do to the high frequency driver unit working with a HxV 90°x60° dispersion, horizontal operation will require the horn/driver unit to be turned. The factory default horn orientation is for vertical operation. If a change of horn direction is required due to horizontal operation, the following steps are to be expedited:

• Remove the 6 screws holding the front cover grille.
• Carefully lift off the front cover grille.
• Remove the 4 screws holding the hom/driver assembly.
• Lift the hom/driver assembly and tum it by 90 degrees.
• Re-fit the 4 screws holding the hom/driver assembly.
• Re-fit the front cover grille.
• Re-fit the 6 screws holding the front cover grille. During any of these operations, make sure no screws of other materials touch the cone of the woofer or the diaphragm of the high frequency driver.
  Do not apply excessive screw torque and always use matching screw drivers to avoid damage to screws.

If being at doubt about the current configuration of the high frequency horn/driver assembly, check the bottom of the high frequency horn. The bottom of the horn is rectangular, and the wider side indicates the 90 degrees horizontal dispersion, the shorter side the 60 degrees vertical dispersion. The speaker shall be mounted in a way that the longer side of the horn’s bottom is in parallel to the floor.

Installatio

VESA mounting (rear)

• Use the speaker with the L-shaped rear panel mounted to point backwards with the VESA mount points and connectors.
• Attach the VESA mount with 4 screws tightly to the rear of the speaker.
• Use a certified safety cable attached to one of the M6 threads if required by law.

FLOWN mounting

PENDANT mounting

COUPLER mounting (top)

Transformer fitting

The 6FP100T can be fitted with an addition, optional line transformer for 100V line operation. The transformer. including a suitable cabling kit, can beobtained as an accessory (item code UTK60)
[ gime”: rittung the line transtormer requires internal recalaling, Only .pxprlitP this work if you

EC Declaration of Conformit

The manufacturer

delto Industries, Unit 4 Britannia usiness Park, C met Way, Southend-on-Sea, Essex, SS2 6GE, United Kingdom
Declares at his sole responsibility that the equipment

INTUSONIC 6FP100T

is in conformity with the following directives/standards/regulations: EMC Directive 2014/30/EU EN55035:2017

LVD Directive 2014/35/EU EN62368 1
ROHS2 Directive 2011/65/EU & 2015/863/EU
EN63000:2018

Read More About This Manual & Download PDF:

References

• INTUSONIC – commercial audio systems – the smart choice

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>