Earphones S800 Bone Conduction Earphone User Manual
- June 12, 2024
- Earphones
Table of Contents
S800 Bone conduction earphone
User Manual
Wearing Method
List
Basic Funtion
Bluetooth name: S800
Speaker: bone conduction vibration speaker
Buttons: 3 mechanical buttons
LED: red light, blue light
Start up
When the headset is off, press and hold the power button for 3 seconds, the
blue LED light will be on for 1 second, and there will be a sound
Shutdown
When the headset is on, press and hold the power button for 3 seconds, the red
LED light will be on for 1 second and there will be a sound
Pairing
Connect to BT: In shutdown state, press and hold the power button for 3
seconds Automatically enter the pairing state after booting, the LED indicator
light flashes red and blue alternately, and there is a headset prompt tone
Automatic shut-down
After the headset is turned on, if there is no operation for more than 5
minutes, it will automatically shut down. The automatic shutdown function is
canceled after connecting to the mobile phone (Bluetooth device
Cancel Dial
Click the “+” button before the call is not answered by the other party to
cancel the call
Answer the phone
When a call comes in, click the “+” button to answer the call 
Refuse to answer
Press and hold the “+” button when there is an incoming call to reject the
other party’s call
Hang up the phone
The call is completed, click the + key to end the call
Connection Succeeded
When the earphone is successfully connected to the device, the blue LED light
will be on for 3 seconds and then turn off, and there will be an earphone
prompt tone
Start SIRI (voice assistant)
Press the power button 4 times in succession to activate the SIRI
function
Stop/Play Music
In the music playing state, click the power button to pause the music
When the music is paused, click the power button to continue playing the
music
Volume up/down
Click the “+” button to increase the volume
Click “-” button to decrease volume
Previous song: Long press the volume button “-” Next song: Long press the
volume button “+”
Automatically reconnect when
booting
The headset automatically reconnects to the last connected device
Switch to TF card mode
In the power-on state, press the power button twice continuously to switch to
the TF card mode (voice broadcast SD card mode after switching), and
automatically play the music in the TF card after switching. If the mobile
phone is connected to Bluetooth, after switching to the TF card, and The
bluetooth of the mobile phone is automatically disconnected. (In the TF card
mode, press the power
Battery Level broadcast
In bluetooth mode and TF card mode, press the power button three times to
announce the power level by voice
The default playback mode is to play sequentially from the beginning. After
pressing the power button four times, it will switch to random play. After
pressing the power button four times, it will play the
It is required that after the playback is paused in TF card mode, if you do
not click the play button within 45 minutes, the headset will automatically
shut down
Power display
After connecting the device, you can see the Bluetooth power display
Low battery reminder
When the battery power is lower than 10%, the red light will flash once
every 5 seconds and there will be a low battery prompt sound every 10 minutes:
Low Battery
Charge
Insert it into the charging USB port to charge the device. The red light is on
during charging and the blue light is on when fully charged. After the
charging cable is unplugged, the light is off. Charging time is about 2 hours
Charging off
After plugging in the charging cable, the headset will reset and power off
for chargin
Power Voice Announcement
In the power-on state, press the power button three times to broadcast the
current power of the headset
Reset
In the off state. press and hold the power button for 10 seconds to restore
the factory settings. After restoring the factory settings, the headset will
automatically turn on
Product parameters
- Bluetooth: 5.3
- Battery: 230mAh
- Input:5V/160mA
- Distance:10M
- Play:greater than 8H@65% volume
- Protocol:HFP,AVRCP,A2DP
- TF card mode supports audio: WAV,MP3,AAC,WMA,FLAC,M4A,AMR
- Waterproof level: IPX8
FCC Warning
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
(1) This device may not cause harmful interference, and (2) this
device must accept any interference received, including interference that may
cause undesired operation.
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The
device can be used in portable exposure condition without restriction.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>