Kuat Sherpa 2.0 Hitch Rack Instruction Manual

Kuat Sherpa 2.0 Hitch Rack

Parts

Included in the bag

Unpacking and assembly instructions

STEP 1. Remove parts box and bracing. Open parts box.

STEP 2. Remove trays. DO NOT remove hitch assembly.

STEP 3. Place trays into build position.

STEP 4. Assemble trays.
Parts Needed:

NOTE: Tighten to 1 Sft-lbs(20Nm), alter nating bolts between each turn. Excessive tightening will damage the rack.

STEP 5. Install rear tray bolt.
Parts Needed:

STEP 6. Install pivot handle.
Parts Needed:

NOTE: After first use, check the main tray bolts for loosening, r e-tighten if needed. Max 1 Sh-16s

Installation instructions

STEP 1. Install into hitch receiver.

STEP 2. Attach the locking hitch pin. Turn the knob to tighting the hitch cam.

Loading bicycles.

STEP 1. Pivot the tray assembly down, using the pivot handle to release the tray.

STEP 2. Open the front tire cradles.

NOTE: Keep front tire cradl-es folded down when not in use.

STEP 3. Fold out the front tire hooks.

NOTE: Keep front tire hooks folded in when not in use to reduce the chance of damage to the hook arms.

STEP 4. Position the front tire hook against the tire and as close to the fork as possible.

NOTE: Proper placement of the tire hook is critical to securing the bicycle to the rack. The tire hook should be as close to the fork as possible.

STEP 5. Ensure rear bicycle tire is properly seated in the rear cradle. Feed strap through ratchet pawl and pull strap down to tighten.

NOTE: When loading bicycles with 20″-24″ front tires an adapter must be used. Please contact Kuat Racks directly by calling toll free 1 (877)822-5828, or by emailing us at [email protected] and a 20″-24″ adapter kit will be provided.

NOTE: Front Tire Safety Strap must be used when driving over rough terrain or with bicycles 35 lbs or heavier.

PARTS NEEDED

NOTE: If you wish to place the tire hook up to 1″ (25mm) away from the fork, you must use the Front Tire Safety Strap. Caution must always be taken to ensure each bicycle is secured on the rack before any travel.

Additional Notes

Locking bicycles.
Loop the lock cable around the frame(s) and insert the latch tip into the lock on the outside tray. 

NOTE: With the tire hooks folded down, the tire hook next to the pivot handle can be used to gain leverage over the pivot handle making it easier to disengage the pivot.

NOTE: The rack can be tilted away providing additional clearance for trunk or rear hatch access.

Tips and Tricks.

• Periodically check all nuts and bolts for proper tightness, not doing so can lead to premature wear or rack failure.
• Lubricate the lock mechanisms using a light oil. Keep the cover on the hitch pin lock at all times.
• The 8mm hex key on the hitch pin can be used to tighten and loosen the cam system.
• Keeping your rack clean will help prevent corrosion and keep the rack working correctly for years.
• The pivot handle is also designed to be used as foot pedal when lowering the trays.
• Make sure the bicycles’ tires are properly inflated and free of leaks. Bicycles can become loose if a tire deflates while in the rack.

Kuat Rack Warnings
SHERPA 2.0

WARNINGS

• Follow instructions for proper assembly, mounting and loading procedures..
• Check tightnQSs of all bolts and screws PQl’iodically.
• Make sure the rack and your vehicle receiver are in good working condition before each use.
• Do not use rack off. road.
• Do not USE hitch extenders with this product.
• Do not use this product on a recreational vehicle or trailer,
• Do not USQ rain or wind. covers or tarps with this product,
• Place the front tire clamp next to the front fork.
• Do not take through automatic carwash.
• Do not use front tire bicycle fenders with this product.
• Front Tire Safety Strap must be used when driving over rough terrain or with bicycles 35 lbs or heavier.

If you nave Question’s or problem’s with your rack please contact KUat Racks directly by calling toll free 1 (877}822•KUAT, or by email: [email protected].

Kuat Racks Limited Lifetime Warranty

Kuat honors the warranty on all Kuat brand products for original owners of the product. Warranty is not transferable. If a Kuat rack that is covered by the terms of this warranty and is determined by Kuat , to be defective, Kuat will repair or replace the defective parts. Kuat may choose in some cases to offer the owner a refund of up to the original purchase price of the product in lieu of repairing or replacing the product. The Kuat warranty does not cover any conditions that are beyond Kat’s control. This includes, but is not limited to, the following: excessive loading. improper assembly, improper installation, theft, or any use that is not consistent with the user guide that is included with the product. The Kuat Warranty does not cover normal wear and tear, scratches, cosmetic oxidation, accidents, or damage due to unauthorized repairs or modifications. If you are the original owner of a defective Küat product, please contact Kuat at 1 (877)822-5828. A Kuat representative will work to quickly resolve the problem. If repairs are necessary, the owner will be responsible for the cost of returning the product to Kuat for repair. No product should be returned to Kuat without prior authorization from Kuat t staff.

LIMIT OF LIABILITY
THIS WARRANTY ONLY COVERS REPAIR, REPLACEMENT OR REFUND FOR THE COVERED KÜAT PRODUCT. ANY DAMAGE TO VEHICLE OR PROPERTY IS NOT COVERED BY THIS WARRANTY. PERSONAL INJURY IS NOT COVERED BY THIS WARRANTY. LIMITATION OR EXCLUSION OF INCIDENTAL DAMAGE IS NOT ALLOWED IN ALL STATES 30 THE ABOVE LIMITATIONS MAY NOT APPLY.

Email: [email protected]

Website: kuatracks.com 

Tel: 1.877.822.5828

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>