KUAT Grip 4, 6 Ski and Snowboard Rack User Guide
- October 30, 2023
- Kuat
Table of Contents
KUAT Grip 4, 6 Ski and Snowboard Rack
Product Information
The GRIPTM is a product that helps to transport skis and snowboards on the roof of a vehicle. It includes two GRIP racks, lock keys, a cool keychain, M5 Allen, (4) M6x25mm Bolt, M4 Allen (2) M6x18mm Washer, (4) Flip Mounts, and crossbars. The GRIP 4 can hold up to 17 lb, while the GRIP 6 can hold up to 23 lb. The maximum weight limit for both is 165 lbs. The maximum crossbar width is 4.25, while the maximum and minimum crossbar height is 2 and .5, respectively.
The product comes with universal FLIPTM mounts that can be used to mount the GRIP racks onto crossbars. The GRIP 6 features two forward mounting locations. Location 1 can be used for any standard crossbars, while location 2 can be used for narrow crossbars or a bias toward one side of the vehicle.
It may be necessary to adjust the angle of the GRIP racks so that they sit level relative to the vehicle roof. The angle adjustment bolt and the provided M4 Allen Wrench can be used to adjust the angle.
Product Usage Instructions
- To unlock and open the GRIPTM, slide the locking tab left to release the GRIP Rack handle.
- Pull the GRIP handle upward to unlatch and open.
- With the GRIP open, align one FLIP Mount and one M6 Bolt with the front bolt hole. Note that the M6x18 Washer is pre-assembled in this location.
- Thread the M6 Bolt into the FLIP Mount and tighten it with the included M5 Allen Wrench.
- Pull against the Tray Tab to unlock, then slide the GRIP Tray outward, exposing the rear mount bolt hole.
- Align the second FLIP Mount, one M6 Bolt, and one M6x18 Washer with the rear bolt hole.
- Thread the M6 Bolt into the FLIP Mount and tighten it with the M5 Allen Wrench.
- Repeat these steps for the second GRIP rack.
- To use the universal FLIPTM mounts, pivot the lever upward to release the strap.
- With both FLIP Mounts open, place the GRIP onto the crossbar in the desired location, looping FLIP straps under and back into the strap lever.
- Close the FLIP Mount lever and repeat for the opposite side.
- Snug mounts to crossbar by retightening the Strap Tensioner using the provided M4 Allen Wrench.
- Check the lever periodically. The lever should be snug, but not too difficult to articulate. Once straps have been properly adjusted to the crossbar, further adjustment should not be necessary to remove or reinstall the GRIP racks.
- Repeat steps 9 – 12 for second GRIP, being sure both GRIP racks are aligned with each other. Always check that GRIP racks are secure prior to travel.
- After each GRIP has been installed to the crossbar, secure the FLIP Mounts using the provided key and integrated lock on the side of each mount.
- To adjust the angle of your GRIP racks so that they sit level relative to the vehicle roof, use the Angle Adjustment bolt and the provided M4 Allen Wrench.
- After adjustment, confirm both GRIP racks are relatively level with the roof of the vehicle and retighten Angle Adjustment bolt.
- To load the GRIPTM, unlock and open each GRIP Rack. Pull against Tray Tabs to unlock and slide GRIP Trays outward. Load thickest skis first, with ski tips toward rear of vehicle. Keep at least .5 of clear space between skis and tray edge to prevent potential for damage when closing GRIP racks.
- Downward facing bindings may cause interference with factory side rails when using the slide out tray feature.
- Once loaded, slide trays in simultaneously to prevent binding. Close and secure each GRIP rack.
- Confirm tab is in the Locked position. Secure Locking Tab with provided key. Always secure and lock each GRIP rack when traveling or storing.
Included
Unlock & Open the GRIPTM
-
Slide Locking Tab left to release the GRIP Rack handle.
-
Pull GRIP handle upward to unlatch and open.
Mounting Universal FLIPTM Mounts -
With GRIP open, align (1) FLIP Mount and (1) M6 Bolt with front bolt hole.
-
Thread M6 Bolt into FLIP Mount and tighten with the included M5 Allen Wrench.
The GRIP 6 features two forward mounting locations.- Location 1 for any standard crossbars.
- Location 2 for narrow crossbars, or a bias toward one side of the vehicle.
-
Pull against the Tray Tab to unlock, then slide GRIP Tray outward, exposing rear mount bolt hole.
-
Align second FLIP Mount, (1) M6 Bolt, and (1) M6x18 Washer with rear bolt hole.
-
Thread M6 Bolt into FLIP Mount and tighten with M5 Allen Wrench
-
Repeat these steps for the second GRIP rack.
Using the Universal FLIPTM Mounts -
Pivot lever upward to release strap.
-
With both FLIP Mounts open, place GRIP onto crossbar in the desired location, looping FLIP straps under and back into the strap lever.
-
Close FLIP Mount lever and repeat for opposite side.
-
Snug mounts to crossbar by retightening the Strap Tensioner using the provided M4 Allen Wrench.
When tightening FLIP straps, check the lever periodically. Lever should be snug, but not too difficult to articulate. Once straps have been properly adjusted to the crossbar, further adjustment should not be necessary to remove or reinstall the GRIP racks.
-
Repeat steps 9 – 12 for second GRIP, being sure both GRIP racks are aligned with each other.
Always check that GRIP racks are secure prior to travel.
Securing FLIPTM Mounts -
After each GRIP has been installed to the crossbar, secure the FLIP Mounts using the provided key and integrated lock on the side of each mount.
GRIPTM Leveling
Depending on your crossbars and vehicle, it may be necessary to adjust the angle of your GRIP racks so that they sit level relative to the vehicle roof. -
Adjust the angle of your mounts and GRIP rack using the Angle Adjustment bolt and the provided M4 Allen Wrench.
-
After adjustment, confirm both GRIP racks are relatively level with the roof of the vehicle and retighten Angle Adjustment bolt.
Loading the GRIPTM -
Unlock and open each GRIP Rack. (See Steps 1 and 2)
-
Pull against Tray Tabs to unlock and slide GRIP Trays outward. (See Step 5)
-
Load thickest skis first, with ski tips toward rear of vehicle. Keep at least .5” of clear space between skis and tray edge to prevent potential for damage when closing GRIP racks.
-
Once loaded, slide trays in simultaneously to prevent binding.
-
Close and secure each GRIP rack.
-
Confirm tab is in the Locked position.
-
Secure Locking Tab with provided key.
Always secure and lock each GRIP rack when traveling or storing.
Küat Rack Warnings
WARNINGS
- Follow instructions for proper assembly, installation, and use.
- Do not exceed vehicle crossbar load limits.
- Load the thickest skis to the rear hinge and thinnest to the rack handle.
- Check load hardware after you have traveled a short distance to confirm a tight fit.
- Keep the handle locked during travel and when storing.
- Lubricate locks and rear hinge bearings at the start and end of each season using graphite or a dry lubricant.
- Do not use tarps, rain covers, or wind covers with this product.
- Do not take through automatic car wash.
- Drive responsibly.
If you have questions or problems, please contact Küat Racks directly by calling toll free 1(877)822-KUAT, or by email: [email protected]
Küat Racks Limited Lifetime Warranty
Küat honors the warranty on all Küat brand products for original owners of the product. Warranty is not transferable. If a Küat rack that is covered by the terms of this warranty and is determined by Küat to be defective, Küat will repair or replace the defective parts. Küat may choose in some cases to offer the owner a refund of up to the original purchase price of the product in lieu of repairing or replacing the product. The Küat warranty does not cover any conditions that are beyond Küat’s control. This includes, but is not limited to, the following: excessive loading, improper assembly, improper installation, theft, or any use that is not consistent with the user guide that is included with the product. The Küat Warranty does not cover normal wear and tear, scratches, cosmetic oxidation, accidents, or If you are the original owner of a defective Küat product, please contact Küat at 1(877)822-5828. A
Küat representative will work to quickly resolve the problem. If repairs are necessary, the owner will be responsible for the cost of returning the product to Küat for repair. No product should be returned to Küat without prior authorization from Küat staff.
LIMIT OF LIABILITY
THIS WARRANTY ONLY COVERS REPAIR, REPLACEMENT OR REFUND FOR THE COVERED
KÜAT PRODUCT. ANY DAMAGE TO VEHICLE OR PROPERTY IS NOT COVERED BY THIS
WARRANTY. PERSONAL INJURY IS NOT COVERED BY THIS WARRANTY. LIMITATION OR
EXCLUSION OF INCIDENTAL DAMAGE IS NOT ALLOWED IN ALL STATES SO THE ABOVE
LIMITATIONS MAY NOT APPLY.
1.877.822.5828
[email protected]