BOSCH PPS7A6M90N Gas Hob Instruction Manual

BOSCH PPS7A6M90N Gas Hob

Product Information

• Product Model: 8001252088
• Gas Type: G20/20 mbar, G20/25 mbar, G25/20 mbar, G25/25 mbar, G25.1/25 mbar, G25.3/25 mbar, G30/29 mbar, G30/37 mbar, G30/50 mbar, G31/37 mbar
• Product Type: Gas Burner
• Usage: Indoor Cooking
• Ignition Type: Manual

Product Usage Instructions

1. Find a flat and stable surface to place the gas burner on.
2. Place the supplied sealing strip on the bottom edge of theburner.
3. Screw the clips and follow the reverse order to remove them.
4. Attach the gas connection angle valve with a G 1/2 gasconnection sealant.
5. For electrical connection, refer to figure 15.
6. To change the gas type, pull out the burner and use a screwdriver to adjust the flexi-hose accordingly.
7. Document the new gas type on the sticker provided and attach it to the burner.
8. Refer to figure 1 for safe installation instructions.
9. The gas burners come with a normal burner, a strong burner, a wok burner, and a multi-crown burner. Refer to figure 16 for more information.

Installation

Safe installation

Follow these safety instructions when installing the appliance.

• Read this instruction manual carefully.
• The images shown in these instructions are for guidance only.
• The appliance can only be used safely if it is correctly installed according to the safety instructions. The installer is responsible for ensuring that the appliance works perfectly at its installation loca-tion.

WARNING ‒ Risk of explosion!

Escaping gas may cause an explosion.

• All Installation, connection, regulating and conver-sion work to a different gas type must be carried out by an authorised professional while taking into account the respective applicable regulations and legal requirements as well as the regulations regarding the local electricity and gas suppliers. Special attention must be paid to the provisions and guidelines that are applicable for the ventila-tion. For conversion work to a different gas type, we recommend that you call the after-sales ser-vice.

WARNING ‒ Risk of poisoning!
Harmful gases may be produced if combustion is in-complete.

• To ensure proper operation, sufficient combustionair must be supplied from the underside of the ap-pliance. Ensure that there is a ventilation openingin the unit under the appliance with a total area ofat least 100 cm2.
  • Ensure that the kitchen is sufficiently ventilated, inparticular when operating the gas cooking appli-ance.
  • Do not connect the appliance to an exhaust gassystem for combustion products.
  • Never install the appliance in boats or in vehicles.
  • The warranty applies only when using the appli-ance as intended.
  • Before installing the appliance, check that thelocal conditions of the supplier are compatiblewith the appliance settings specified on the ratingplate (type of gas and pressure, power, voltage).
  • Secure the power cord to the cabinet to prevent itfrom touching hot parts of the oven or hob.
  • Before any work is carried out on the appliance,switch off the power supply and the gas supply.
  • Connect the appliance to the power supply usingthe earth.
  • Do not make any changes to the inside of the ap-pliance. If required, contact our technical cus-tomer service.

Before installing

• This appliance is a class 3 appliance in accord-ance with the EN 30-1-1 standard for gas appli-ances: Built-in appliance.
• The unit in which the appliance is installed mustbe stable and secured appropriately.
• The units in the vicinity of the appliance, the lamin-ated panels and the adhesive with which they aresecured must be made of non-flammable, heat-resistant materials.
• Do not install this appliance above refrigerators,washing machines, dishwashers or similar.
• The appliance must only be installed on an ovenwith forced ventilation. Check the dimensions ofthe oven in the installation instructions for theoven.
• If you install an oven underneath the hob, the worksurface thickness may differ from the dimensionsgiven in these instructions. Take note of the in-formation in the oven installation instructions.
• If you install an exhaust air fan or an extractorhood, refer to the installation instructions for these.Always observe the minimum vertical distance tothe hob.
  → Fig. 1

Preparing the units

• Make a cut-out in the worktop with the required di-mensions depending on the relevant installationmethod: Standard (a) or flush (b).
  → Fig. 2

• Seal the cut surfaces of wooden work surfaceswith a special glue seal to protect them from mois-ture.

• If there is no built-in oven underneath the hob, in-sert a non-flammable separator (e.g. metal or ply-wood) at a distance of 10 mm from the hob. Thisprevents access to the underside of the hob. The distance from the intermediate floor to the mainsconnection for the appliance must be at least 10mm.
  → Fig. 3, → Fig. 4

Preparing the furniture item for flush installation

• All cutting work on the work surface must be car-ried out in a specialist workshop.
• The cuts must be clean and precise because thecutting edge is visible on the surface. The stabilityof the units must also be ensured after the cuttingwork.
• Only use special, temperature- and water-resistantwork surfaces (e.g. natural stone or tiles).
• The fitted unit must be heat-resistant up to 90 °C.

Positioning the appliance

Note: Do not use silicone to bond the appliance tothe worktop.

1. Position the hob with the upper side facing downon a flat, stable surface.

2. Apply the adhesive seal supplied to the loweredge of the hob. The adhesive seal prevents thepenetration of liquids.
   → Fig. 5

3. Screw the brackets supplied into the specified po-sition so that they can turn freely.
   → Fig. 6

4. If you install the appliance in a 480 mm wideniche, you must remove the spacer, which is pre-installed on the back of some models.
   → Fig. 7

5. Turn the hob around and insert it into the recess.Insert the hob in the front of the recess.
   → Fig. 8

6. Turn the brackets and tighten them fully.
   → Fig. 9
   The position of the brackets depends on the work-top thickness.

Installing the appliance flush

1. Install the appliance so that there is an even gapall around it. → “Positioning the appliance”,Page 10

   • The hob should be slightly below the work sur-face. On tiled worktops, the contact surfacescan be raised, if necessary, with temperature-and water-resistant rails.
     → Fig. 10

2. Check that the appliance works correctly and is inthe correct position.

3. Fill the gap between the work surface and the hobusing a suitable commercially available siliconeadhesive.
   → Fig. 11
   Smooth the silicone adhesive with a spatula or afinger wetted with soap before a solid layer forms.
   Note: Leave the silicone adhesive to dry before youuse the appliance.
   Tip: If you use an unsuitable silicone adhesive onnatural stone work surfaces, it may cause discolour-ation that can no longer be removed. A suitable ad-hesive is available from our technical customer ser-vice.

Removing the appliance

1. Disconnect the appliance from the electricity andgas connections.
2. Unscrew the brackets and proceed in reverse or-der.

Connecting the gas

Observe the country-specific guidelines.
CAUTION ‒ Risk of explosion!
A gas leakage may cause an explosion.

• If any connection is handled, check the seal.
  • Arrange the gas connection so that the shut-off valve is accessible.
  • Ensure that the information on the rating plate regarding the gas type and gas pressure complies with the local connection conditions.
  • Connect the appliance to a fixed gas pipe or a flexible metal pipe.
  • The flexible metal pipe must not come into contact with the moving parts of the unit in which the appliance is installed (e.g. a drawer) and must not be routed through any spaces which might become obstructed.
  • Gas connection elbow on the appliance: R 1/2.
  • Do not move or twist the gas connection elbow.

Spare parts for gas connection
You can obtain the gas connection parts from the technical customer service.

• Seal 00034308
• Gas connection elbow: G 1/2 10006024

Gas connection R 1/2
→ Fig. 12

Gas connection G 1/2

1. Replace the gas connection elbow on the appliance with the gas connection elbow G 1/2 supplied in the accessory bag.
   → Fig. 13

2. Insert the seal between the gas connection of the appliance and the gas supply.
   → Fig. 14

Electrical connection

• This appliance is type Y: The connection cable must only be replaced by technical customer service and not by the user. The cable type and the minimum cross section must be respected.
• The hobs are supplied with a power cord with or without a plug.
• Only connect appliances that are fitted with a plug to a correctly installed socket with protective earth conductor.
• If the plug is not accessible to the user, an all-pole isolating safety switch with a minimum contact opening of 3 mm must be provided.
  → Fig. 15

Converting the gas type
If the country’s regulations allow, this appliance can be adapted to other types of gas, if these are listed on the rating plate.
You can find the right parts in the bag that is supplied with the appliance or you can obtain them from customer service. The table → Fig. 21 shows the right combination for the relevant burner and gas type.

C Economy burner
D Standard-output burner
E High-output burner
G Wok multi-crown burner

Adjusting the taps

1. Turn the rotary knobs to the minimum power position and pull them out.

2. With the tip of the screwdriver, push down on the flexible rubber holder to access the bypass screw.
   → Fig. 16
   Never remove the sealing ring. The sealing rings prevent liquids and dirt from finding their way into the appliance and impairing its ability to function properly.

3. When adjusting the bypass screws (M), refer to the table → Fig. 21 .

   • A: Firmly tighten the bypass screws.
   • B: The bypass screws must be flush with the fitting.
     → Fig. 17

Replacing the nozzles

1. Remove all pan supports, burner caps and distributors.

2. On some appliances, the multi-crown burner may have a metal plate attached to it. Unscrew and remove the metal plate.
   → Fig. 18

3. Replace the nozzles using the appropriate wrench and tighten them carefully to guarantee the seal.
   → Fig. 19 , → Fig. 20
   Ensure that the nozzle does not become detached during removal or fastening.

4. If the appliance is equipped with a metal plate on the wok burner, screw the metal plate back on.

Reinstalling the appliance

• Install the appliance components in reverse order.
  Checking if equipment is working

  1. Check that turning the rotary knob between the position for maximum power and the position forminimum power does not cause the burner to go out or result in backfire.
  2. If the gas flow from the burner is not correct, in the table → Fig. 21 , check whether the nozzle and the position of the bypass screw are correct.

Documenting the gas type conversion

• Attach the sticker showing the new gas type near to the rating plate.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>