HARPER HTP-5T01 Thermo Pot Instruction Manual

HARPER HTP-5T01 Thermo Pot

Thank you for choosing HARPER products. Before using, read the instruction manual and save it in case of questions about the maintenance of the device.

PRECAUTIONS

Attention! 7b avoid electric shock, fire and burn risk, observe the following precautions:

• Before using the thermopot, carefully read the entire instruction and save it for reference in the future. Improper handling of the kettle can cause the device to break down and cause harm to the user.

• The device is allowed to be used only for domestic purposes, it is not intended for industrial use.

• Do not use the device outdoors. Protect it from heat, direct sunlight and humidity.

• Make sure that the voltage and current frequency match the ones indicated on the label of the device.
  Attention! This device must be grounded. In the case of a short circuit of the electrical circuit, the grounding reduces the risk of electric shock, since it has an electric current outlet wire. The device is equipped with a cable with a ground wire and a grounding plug. This plug must be inserted into a properly installed and properly grounded outlet.

• Set the thermopot in a well-ventilated place.

• Do not cover the device.

• Do not immerse the device body, power cord or plug in water and other liquids.

• If water or other liquids contact the case, cord or plug of the device, immediately disconnect the device from the power supply.

• Disconnect the device from the power supply if it is not in use, as well as when cleaning it or in case of malfunctions.

• After transporting the thermopot in conditions of low temperature, it is allowed to use the device only after two hours after putting it in a warm condition.

• Do not fill the device with water above the «FULL» mark.

• Thermopot is only for water heating. To avoid breakage of the device, do not heat other liquids in it. Do not add tea leaves inside.

• Close the lid securely before boiling. Do not block the steam output with anything. Do not move the thermopot during operation to avoid the risk of scald.

• Before turning on the thermopot, make sure that the lid is tightly closed to avoid splashing water.

• Some parts of the device get very hot during operation. Do not touch hot surfaces with your hands.

• When disconnecting the thermopot from the power supply, hold your hand on the plug, do not pull the power cord.

• Never leave the working thermopot unattended.

• This appliance can be used by children aged from 1 O years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervi­sion or instruction concerning use of the appliance in a safe way and understand the hazards involved.

• Do not use a thermopot with a damaged power cord or plug. To re­place the power cord, contact an authorized service center.

• Do not try to disassemble and repair the device yourself. For the pur­pose of repair, please contact the service center.

• Unskilled repairing can lead to breakdown and cause harm to the user.

• to avoid overloading the power supply, do not use the thermopot at the same time as other energy-intensive devices.
  ONLY FOR DOMESTIC USE!

• Keep the instruction for the entire service life!

BEFORE USE

• Gently unpack the thermopot, save all packaging materials until you find all the parts of the device and make sure it works.
• It is recommended to keep the packaging in case you need to pack the device and move it.
• Wipe off dust that may have gripped on the device during packaging with a soft, damp (not wet) cloth and dry thoroughly.
• Do not use abrasive materials to avoid surface damage.
• During the first use, twice fill the thermopot to the maximum mark with cold water, boil and drain the water. Then rinse the thermopot with cold water.

EQUIPMENT

• Thermopot – 1 pc
• Cup stand – 1 pc
• Instruction – 1 pc
• Warranty card – 1 pc

DEVICE DIAGRAM:

OPERATION OF THERMOPOT

Getting started

• Install the stand as shown on the picture.
• Press the lid button to open.
• Fill the thermopot with water from another container, while not filling it above the «FULL» mark.
• Close and securely snap the lid.
• Connect the power cord to the thermopot housing and connect it to the electrical outlet.
• The screen will light up and after a moment only the Power On/Off symbol is left, the device is in standby mode now.

Boiling water and maintaining temperature

• Press the button, the device will start working
• After the water temperature rose to 100°C, the boiling button will flash for 60 seconds, then turn off, the device will go into temperature main- tenance mode Bv default. the temnerature is set to 85°C
• To change the temperature mode, press the button, the following modes will change cyclically: 85°C, 75°C, 65°C, 55°C, 45°C, temperature set cancellation (the symbol cy on the screen), 95°C.
• To re-boil, press the button.
• To cancel boiling, press the button again.
• At first use add water, boil and drain water 2-3 times.
• If you add water to the thermopot in the temperature maintenance mode, the temperature sensor will start re-boiling the water.
• When opening the lid, be careful to avoid burns during hot steam is going out.

Thermos mode

• To save energy, you can set the device to thermos mode. In this mode, the water in the thermopot will cease to heat up, maintaining the tem­perature due to the thermal insulation of the internal container.
• To enter thermos mode, press and hold the button for 5 sec-onds.
• The power indicator will be on the display.
• In thermos mode, the water supply function remains available.

Water supply and locking

• To supply water using an electric pump, first press the button, the indicators of the and buttons will light up.
• Press and hold the button.
• If no button is pressed within 1O seconds, the electric pump will auto­matically lock.
• To disable the lock function, press the button and hold it for 5 seconds,the button, it will flash 3 times. After that, water can be poured using the button.
• To re-enable the lock function, press the button again.

Fast cooling

• Press and hold the button for 5 seconds, the cooling light will flash on the display.
• The indicator will be lit constantly after reaching the set temperature.
• To exit the cooling mode, press the button for 5 seconds again.

Clean water (Eco) and tap water modes

• After turning on the device, the tap water mode is activated by default, in which boiling occurs, then maintaining the set water temperature. When boiling, dechlorinating occurs, which improves water quality.
• If you use bottled or purified water, which can be drunk without boil­ing, you can activate the eco-mode.
• To activate the eco-mode, press the button, an indicator will light up.
• In this mode, there is no boiling, by default the temperature is set to 45

Reminder of the low water level

• When the water level drops below the minimum level, an indicator  lights up to remind you to add water.
• Heating is switched off to prevent overheating.
• After adding water, the heating is switched on automatically.

CARE AND CLEANING

This device requires minimal maintenance. It doesn’t include spare parts. Don’t try to fix it yourself. If you need to fix it, contact a qualified professional.
Attention! Before cleaning, always turn off the device from the outlet and let it cool.

• Make sure the thermopot is cold.
• Open the lid and empty the thermopot.
• Wipe the thermopot with a dry, clean, soft cloth.
• Never use abrasive materials to clean the thermopot.

Removing and installing the lid
For ease of cleaning, you can remove the cover of the thermopot.

• To remove the lid, lift the lid lock up.
  Attention: Never remove the cover from the working thermopot.

• After installing the cover, lower the lid lock down.

Tips for getting rid of strange odors in the thermopot
To get rid of strange odors after boiling water, and thus remove its unpleas­ant taste of drinks, use one of the methods described below:

1. Lemon juice. Pour the juice of three or four lemons into the thermopot, fill it with water until the «FULL» mark is reached and begin boiling. After that, leave the solution for a few hours and boil the solution again, then rinse the thermopot with cold water. Repeat these steps if necessary.
2. Citric acid. Fill the thermopot with water until the «FULL» mark is reached and pour citric acid there at the rate of 20 g per 1 liter of water. Boil and leave the solution for a few hours, then boil the solution again, drain it, then rinse the thermopot with water.
3. Lemon peel. Fill the half of thermopot with lemon peel and pour water to the «FULL» mark. Boil and leave it for several hours. Then boil again, remove the lemon peel from the thermopot and rinse it with water.
4. Vinegar or vinegar essence. Pour water into the thermopot, add half a cup of 9% vinegar or 2 tablespoons of 70% vinegar essence. Heat the thermopot without bringing the solution to a boiling condition, as it can spill over the edge when boiling. Repeat 2-3 times, drain the solution and rinse the thermopot with water.
5. Baking soda. Pour water into the thermopot, add 3 tablespoons of baking soda, boil the water, wait until it cools, and boil again. Then drain the entire solution and rinse the thermopot with water.

Removing of scale (when using tap water}
Impurities in tap water contribute to the formation of scale on the met­al parts of the thermopot, which negatively affects the taste of drinks. To neutralize scale, use the following tips:

• Boil water in a thermopot containing vinegar solution. To do this, fill the thermopot with water, add 2-4 tablespoons of table vinegar and bring it to a boiling condition. Then rinse with plenty of clean water. Leave the thermopot open for a day in a well-ventilated room.
• Use specialized cleaning products.

STORAGE CONDITIONS

• Disconnected from the power thermopot must be cooled and washed.
• Store the device in a box in a clean and dry place.
• Do not put the thermopot in the box unless it is plugged off from the outlet and cooled.

WARRANTY AND REPAIR

This device was manufactured and tested according to the necessary meth­ods. The manufacturer provides a guarantee for the normal operation of the device for 12 months from the date of purchase, compliance with the condi­tions specified in the warranty card of the product and the following points:

• All defects related to defects in materials and manufacturing are elim­inated free of charge during the warranty period. Complaints must be registered immediately after the discovery of deficiencies.
• Damage caused by improper handling, maintenance, improper instal­lation or maintenance, with unqualified connection or installation, as well as force majeure or other external influences, is not subject to warranty obligations.
• We reserve the right, upon receipt of a complaint, to repair or replace faulty parts, or to exchange the device. Replaced parts pass into our ownership.
• On the basis of the warranty, no further claims are possible. The buy­er receives the right to a warranty, on condition of presentation of a correctly filled out warranty card.
• Terms of warranty repair, addresses of authorized service centers can be found on the company’s website www.harper.ru
  Additionally: if the device has ceased to function properly, before contacting the service center, we suggest first checking whether there are other reasons for this, such as, for example, an interrupted power supply.

SAFE DISPOSAL

This marking indicates that this product should not be disposed of together with other household waste throughout the EU. To prevent possible harm to the environment or human health by uncontrolled waste disposal, dispose of it responsibly to pro­mote sustainable reuse of material resources. To return a used product, use the return and collection systems or contact the seller from whom the product was purchased, who can accept this product for environmentally friendly disposal.

Information on restrictions in the use of technical means, taking into account its purpose for work in residential, commercial and in­dustrial areas:
The equipment is designed to work in residential and commercial areas, public places, industrial areas with small and medium power consump­tion, without exposure to harmful and dangerous production factors. The equipment is designed for operation without the constant presence of service personnel.

TERMS AND CONDITIONS OF CARRIAGE (TRANSPORTATION)

Equipment must be transported in original packaging in covered vehicles by any mode of transport.

SPECIFICATIONS

• Power supply: 220-240 V, 50-60 Hz
• Power: 1200W
• Volume: 5L
• Dimension: 365 mm x 220 mm x 290 mm
• Weight: 2,7 kg

TROUBLESHOOTING

Malfunctions| Probable causes| Methods of
elimination
---|---|---
White sediment or scale inside the thermopot| Using hard water| Clean the thermopot from scale
Unpleasant odor| Chlorinated water may have an unpleasant smell after boiling| Use the re-boiling function to get rid of the odor
When using the device on a plastic surface, the smell of plastic can get into the water through the pump
The water supply does not work immediately after boiling| The filter is blocked| Clean the filter with a brush
Air bubbles in the pump| Open and close the lid and try again
The water supply does         The pump is blocked

not work

| Click the unlock button
 | The socket is faulty| Check for voltage in the outlet
Hot water flows out         The water level is above spontaneously the maximum mark| Drain the water below the maximum mark
---|---

The external surface of the device is very hot

| During operation of the device, its surface may heat up to 65°C if the room temperature is high|

This is not a malfunction

Error «E1»| Damage to the thermistor circuit| Contact the service center
Error «E2»| Short circuit of the thermistor circuit| Contact the service center
Error «E3»| The overheating protection has been activated| Contact the service center

The products passed all the assessment procedures established in the technical regulations of the Customs Union and the Eurasian Economic Union.
The product complies with all necessary technical regulations of Eurasian Community. Detailed information about product certification, technical regulations, certificate number and date, validity period, issuing organization you can find on the website http://harper.ru/ certification or by calling technical support 8-800-600-7 107
Life duration of product: 36 months
Warranty period: 12 months
Warranty service is provided on the base of warranty card that goes together with thy product. Warranty card and User manual are inevitable parts of the product. For additional information about the product and authorized service centers you may find at www.harper.ru or by telephone 8-800-600-7 107.
Manufacture: Harper International Trading Limited 1 SF, Radio City, 505 Hennessy Road, Causeway Bay, HongKong
Made in PRC
Importer: LLC «Progress-Plyus», App.11, floor 2, Build.SO, k. 1, Udaltsova Str., Moscow, Russia, 119607, tel: +7495 1330210, info@harper.ru

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>