BOSCH SBD6ECX00E Dishwasher Instruction Manual

SBD6ECX00E Dishwasher

Product Information: Dishwasher

The Dishwasher comes with a Home Connect feature that allows you to connect your appliance to a mobile device and change all settings using the Home Connect app. The appliance also has a water softening system that can be set using the basic settings. The appliance has a dispenser for special salt, rinse aid, and detergent. The programme data has been measured in the laboratory according to European standard EN 60436. The consumption figures depend on the programme and additional function selected.

Product Usage Instructions

Setting up Home Connect:

1. Install the Home Connect app on your mobile device and follow the instructions.
2. Scan the QR code with the Home Connect app.

Setting the water softening system:

1. Press the power button.
2. Press and hold the basic settings button for 3 seconds.
3. Press the + or – button repeatedly until the right water hardness value has been set.
4. To save the settings, press and hold the power button for 3 seconds.

Adding special salt:

1. Unscrew the lid of the dispenser for special salt and remove it.
2. On initial start-up, fill the dispenser with water.
3. Add the special salt to the dispenser. Never add detergent.
4. Place the lid back on the dispenser and turn to close it.

Adding rinse aid:

1. Press the catch on the lid of the dispenser for rinse aid and lift it.
2. Add rinse aid up to the max mark.
3. Close the lid of the dispenser for rinse aid. The lid clicks into position.

Adding detergent:

1. Add the detergent to the dry detergent dispenser.
2. Close the lid of the detergent dispenser. The lid clicks into position.

Programmes:
The appliance has several programmes with different durations, energy consumption, and water consumption. Select the appropriate programme based on your needs.

How to use your appliance:

1. Load the tableware. Only clean tableware that is suitable for dishwashers. Remove large remnants of food from the tableware. Check that the spray arms can rotate freely.
2. Add detergent to the detergent dispenser.
3. Switch on the appliance.
4. Select the appropriate programme.
5. Start the programme.
6. Remove the tableware at the end of the programme.
7. To cancel the programme, press and hold the power button for approximately 4 seconds.

Before using for the first time, read the instruction manual and the safety information it contains.

Setting up Home Connect

Tip:  Connect your appliance to a mobile device. You can conveniently change all settings using the Home Connect app.

1. Install the Home Connect app on your mobile device and follow the instructions.
2. Scan the QR code with the Home Connect app.

Overview of water hardness settings

You can find an overview of the water hardness values that can be selected here.
A table of country-specific units can be found in the instruction manual.

Setting the water softening system

1. Press  ⁠.
2. To open the basic settings, press  for approx. 3 seconds.
   • The display shows Hxx.
   • The display shows Set ⁠.
3. Press Start repeatedly until the right water hardness has been set.
4. To save the settings, press   for 3 seconds.

Programmed

The programme data has been measured in the laboratory according to European standard EN 60436.
The consumption figures depend on the programme and additional function selected.
The running time will change if the rinse aid system is switched off or rinse aid needs to be added.

1. Suitable programme for running at night: it takes longer, but is extremely quiet
2. half standard load

Adding special salt
To avoid damage to the appliance, only add special salt to the dispenser for special salt just before the programmed starts.

1. Unscrew the lid of the dispenser for special salt and remove.
2. On initial start-up: Fill the dispenser right up with water.
3. Add the special salt to the dispenser. The water in the dispenser is displaced and forced out. Never add detergent.
4. Place the lid back on the dispenser and turn to close.

Adding rinse aid

1. Press the catch on the lid of the dispenser for rinse aid and lift ⁠.

2. Add rinse aid up to the max mark.

3. Close the lid of the dispenser for rinse aid.
   The lid clicks into position.

Adding detergent

1. Add the detergent to the dry detergent dispenser.

2. Close the lid of the detergent dispenser.
   The lid clicks into position.

How to use your appliance

1. Load the tableware.
   Only clean tableware that is suitable for dish-washers.
   Remove large remnants of food from the tableware.
   Check that the spray arms can rotate freely.

2. Add detergent.

3. Switch on the appliance ⁠.

4. Select the programmed.

5. Start the programmed

6. Remove the tableware at the end of the programmed.

7. To cancel the programmed, press for approx. 4 seconds.
   The programmed is cancelled and ends after approx. 1 minute.

Cleaning filters

1. After each wash check the filters for residue.

2. Rotate the spray arm to the side to make room for filter cleaning.

3. Turn the coarse filter anticlockwise and remove the filter system ⁠.
   

4. Pull down the micro filter to re-move.

5. Press the locking catches together and lift the coarse filter out ⁠.

6. Clean the filter elements under running water.

7. Re-assemble the filter system.

8. Insert the filter system into the appliance and turn the coarse filter clockwise.
   Make sure that the arrow markings match up.
   The spray arm will automatically return to the correct position when starting, so it is not necessary to reposition the spray arm to the front.

Cleaning the spray arms

1. Unscrew the upper spray arm and pull down to remove ⁠.

2. Position the lower spray arm as shown , grip in the middle and pull up to remove

3. Check the outlet nozzles on the spray arms for blockages under running water and remove any foreign bodies.

4. Insert the lower spray arm.

   • The spray arm clicks into position.

5. Insert the upper spray arms and screw firmly in place.

Clean wastewater pump

1. Disconnect the appliance from the power supply.

2. Remove the filter system.

3. Scoop out any water.

4. Prize off the pump cover using a spoon and grip it by the crosspiece.

5. Lift the pump cover inwards at an angle and remove.

6. Remove any remnants of food and foreign bodies in the area of the impeller.

7. Insert the pump cover and press down ⁠.
   The pump cover clicks into position.

8. Install the filter system.

Troubleshooting

Fault
E:3-200 or indicator for water supply lights up.

Cause and troubleshooting
Supply hose is kinked.

• Install the supply hose without kinks.

Water tap is turned off.

• Turn on the water tap.

Water tap is jammed or furred up.

• Turn on the water tap.
  The flow rate must be at least 10 l/min when the water supply is open.

The filters in the water connection of the supply or Aqua Stop hose are blocked.

1. Switch off the appliance.

2. Pull out the mains plug.

3. Turn off the water tap.

4. Unscrew the water connection.

5. Remove the filter from the sup-ply hose

6. Clean the filter.

7. Re-insert the filter in the supply hose.

8. Screw the water connection back on.

9. Check the water connection for leaks.

10. Restore the power supply.

11. Switch the appliance on.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>