AXOR 13284000 Ecostat 1001 SL Care Thermostatic Bath and Shower Mixer Instruction Manual
- October 30, 2023
- AXOR
Table of Contents
- AXOR 13284000 Ecostat 1001 SL Care Thermostatic Bath and Shower Mixer
- Product Information
- Product Usage Instructions
- Models
- Safety Notes
- Installation Instructions
- Technical Data
- Assembly
- Adjustment/Safety Function
- Maintenance
- Dimensions
- Spare parts
- Operation
- Troubleshooting
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
AXOR 13284000 Ecostat 1001 SL Care Thermostatic Bath and Shower Mixer
Product Information
The product is a shower system with a thermostatic mixer that can be used for bathing, hygienic, and body cleansing purposes. It has technical specifications of operating pressure of 1.6MPa, recommended operating pressure of 20 l/min, and a test pressure of 1 MPa. The hot water temperature is recommended to be set according to the user’s preference. The shower system is equipped with an anti-pollution function and must not be used by children, adults with physical, mental, or sensoric impairments without proper supervision, or persons under the influence of alcohol or drugs.
Product Usage Instructions
Safety Notes
Gloves must be worn during installation to prevent crushing and cutting
injuries. The hot and cold supplies must have equal pressures.
Installation Instructions
The fitting must be installed, flushed, and tested after the valid norms. Do
not use silicone-containing acetic acid. After installation, check the output
temperature of the thermostat. A correction is necessary if the temperature
measured at the output differs from the temperature set on the thermostat.
Maintenance
Regular maintenance is required to keep the shower system working efficiently.
Refer to page 63 for maintenance instructions.
Operation
Refer to page 66 for operating instructions.
Faults
- Insufficient water: Check if the crossflow is happening, hot water is being forced into the cold water pipe, or vice versa when the mixer is closed.
- Spout temperature does not correspond with temperature set: Check if temperature regulation is possible.
- Shower or spout dripping: Check if the anti-pollution function is working correctly.
Models
Safety Notes
- Gloves should be worn during installation to prevent crushing and cutting injuries.
- The shower system may only be used for bathing, hygienic and body cleansing purposes.
- Children as well as adults with physical, mental and/or sensoric impairments must not use this shower system without proper supervision. Persons under the influence of alcohol or drugs are prohibited from using this shower system.
- The hot and cold supplies must be of equal pressu-res.
Installation Instructions
The fitting must be installed, flushed and tested after the valid norms!
Thermostatic mixer in conjunction with combination boilers
- If fitting a hand shower remove the water limiter from the shower.
- If the continuous water heater causes any problems, or you have different water pressures you must install a water limiter to the cold supply, (ordered separately,article number 97510000).
Technical Data
- Operating pressure: max. 1 MPa
- Recommended operating pressure: 0,1 – 0,5MPa
- Test pressure: 1,6MPa (1 MPa = 10 bar = 147 PSI)
- Hot water temperature: max. 80°C
- Recommended hot water temp.: 65°C
- Rate of flow by 0,3 MPa: 20 l/min anti-pollution function
Do not use silicone-containing acetic acid!
Assembly
Test certificate
| PA-IX | DVGW | SVGW | ACS | WRAS | KIWA | NF | |
|---|---|---|---|---|---|---|---|
| 13282000 | PA-IX 9373/IB | X | X | X | X | X | |
| 13284000 | PA-IX 9374/IBB | X | X | X | X | X |
Adjustment/Safety Function
After the installation, the output temperature of the thermostat must be checked. A correction is necessary if the temperature measured at the output differs from the temperature set on the thermostat.
Maintenance
- To guarantee the smooth running of the thermostat, it is necessary from time to time to turn the thermostat from total hot to total cold.
- The mixer is equipped with non-return valves. The non-return valves must be checked regularly according to DIN EN 1717 in accordance with national or regional regulations (at least once a year).
Dimensions
13284000
13282000
Spare parts
Operation
Troubleshooting
Hansgrohe
Postfach 1145 · D-77761 Schiltach · Telefon +49 (0) 78 36/51-1282 · Telefax
+49 (0) 7836/511440
E-Mail: info@hansgrohe.com · Internet:
www.hansgrohe.com.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>