EGLO 203727A Henessy 1-Light Black and Brushed Nickel Wall Sconce Instruction Manual
- October 30, 2023
- EGLO
Table of Contents
203727A Hennessey 1-Light Black and Brushed Nickel Wall Sconce
Instruction Manual
203727A Hennessey 1-Light Black and Brushed Nickel Wall Sconce
Wall sconce
Use (1) 60-watt maximum Type A bulb (not provided)
Cleaning Instructions
Do not use polish or cleaners. Wipe clean with soft cloth.
- Install the glass(2) with clip to the fixture(3).
- Attach the Mounting Plate (P1) to the Outlet Box with screw (P2).
- Connect Black Wire L of the Outie Box to the Main Wire(black) of the Fixture with wire nuts (P5).
- Connect the White Wire N of the Outlet Box to the Main Wire (white) of the Fixture with wire nuts (PS).
- Install the Ground Wire E to the Mounting Plate (P1) and connect it into the Outlet Box.
- Fix the fixture to the Screw (P3) of the Mounting Plate (P1) till tight with decorative nuts (P4).
- Screw in Light Bulb (1).
Warranty
WHAT IS COVERED
‘The manufacturer warrants this lighting fixture to be free from defects in
materials and workmanship for a period of one (1) year from date of purchase.
This warranty applies only to the original consumer and only o products used
in normal use and service. If this product is found to be defective, the
manufacturer’s only obligation, and your exclusive remedy, is the repair or
replacement of the product at the manufacturer’s discretion, provided that the
product has not been damaged through misuse, abuse, accident, modifications,
alterations, neglect or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been
improperly installed, set-up, or used in any way not in accordance with the
instructions supplied with the product. This warranty shall not apply to a
failure of the product as a result of an
accident, misuse, abuse, negligence, alteration, or faulty installation, or
any other failure not relating to faulty material or workmanship.
This warranty shall not apply to the finish on any portion of the product,
such as surface and/or weathering, as this is considered normal wear and tear.
The manufacturer does not warrant and specifically disclaims any warranty,
whether express or implied, of fitness for a particular purpose, other than
the warranty contained herein. The manufacturer specifically disclaims any
liability and shall not be liable for any consequential or incidental loss or
damage, including but not limited to any labor/expense costs involved in the
replacement or repair of said product.
Safety Information
WARNING: Carefully read and understand the Information given in this
manual before beginning the assembly and installation. Failure to do 50 could
lead to electric shod, fire or other juries which could be hazardous or even
fatal.
WARNING: Be sure the electricity to the wires you are working on is shut
off. Either remove the fuse or tum the circuit off.
NOTICE: Changes or modifications not expressly approved by the parley
responsible for compliance could void the user’s authority lo operate the
equipment.
General Safety Information
Eiocircal retaliations may only tic csred out by pi Ate4,1 otoctrotions Please
note Before proceeding with Installation mains connect Ung cable must be de-
synergized (fuse turned off). Please not the %atlas-Ing symbols and nifty
instruchearts n order to avail damage caused Dy atibiereCt assent)) Or use
Protection class 1. Lair pi sit Chi symbol Connects hem on tho newcoin.
sole w M the yoilmsgram protective earth to the proloc-tNe Garth terminal
Protection class 2: lot tams MITs symbol no Protective conductor
necessary for safe operation
Protection class 3: Only operate lamps won this symbol with Sa-fete Extra
Low Vtte (SELVI Ong connect to SELV omits
Alninture distance: The symbol explains ewe minimum ekitincle of the
Illuminant to the lentils horney flammable surface
Downlights: This mystic explain that the tamp is anal suitable fa
covering with thermal insulting matters
Changes Do viol mewl any changes to the yarn a is connecting cable
Connecting cable The exterior flexible cable of this Ishi cannot boreal cad
Scrap the in, if this cable is damaged Commissioning- Do not rest the Lamp or
Its connecting cable show visible signs of damage Changing Illuminant &flare
replacing the Annan ensure that the tight a not iris Lights and illuminants
will become hot in operation Ablow them to cool baton change Use city the
Durant specified on the it The maximum power per illuminant may riot be
exceeded Mao. d applicable the prescribed Ruminant type must be observed Can
advice: Only clean lights when tuned oft dO not allow any moisture into
connecting areas or on current-carrying parts Deanna agents can cause staining
Email our customer service at
info.usa@eglo.com
or call 1-877-892-0007
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>