Lucci decor 050649 Flute Pendant Light with 5 Lights Instruction Manual
- June 4, 2024
- Lucci decor
Table of Contents
Lucci decor 050649 Flute Pendant Light with 5 Lights
Thank you for purchasing this quality Lucci product. To ensure correct function and safety, please read and follow all instructions carefully before assembly, installation and use of this product. Please keep instructions for future reference.
Warranty
- This luminaire is covered by a 12-month warranty. The warranty is from date of purchase, not the date of installation.
- If the luminaire is not assembled and installed by a licensed electrician, the warranty will be void.
- Please retain the proof of purchase and evidence of installation by a licensed electrician for any warranty enquiries.
- Warranty will be void if there is any damage due to improper usage or modification to the luminaire.
- Failure to comply with the instructions in this manual may increase the risk of damage or injury and will void the warranty.
Installation Requirements
-
This luminaire must be assembled and installed by a licensed electrician.
-
All wiring and installation of the luminaire must adhere to the latest local and national wiring rules.
-
E. g. AS/NZS 3000 Electrical Installations Do not exceed the maximum wattage rating.
-
This luminaire is a Class I product and must be earthed during wiring and installation.
-
Do not exceed the maximum wattage rating.
-
This luminaire is suitable for use with LED lamps only.
-
Compatible with G9 LED lamps of 28mm or smaller.
-
SKU# 121350 / SKU# 121351 G9 lamps are recommended.
-
Select a suitable location for installation:
- This luminaire is suitable for indoor use only.
- The mounting point must support 2 times the weight of the luminaire.
- Ensure the luminaire is not installed in direct line of an air vent/system.
- If installing a luminaire in an area prone to moisture, ensure that the area is well ventilated, and an appropriately rated exhaust fan is used if required. Damage or corrosion caused by moisture is not a product fault, and as such is not covered under warranty.
-
Take care not to pull any electrical wires during unpacking as this may damage the connection.
-
Lay out all the components on a smooth surface and make sure no components are missing before assembling.
If parts are missing, return the complete product to the place of purchase for inspection or replacement. -
Check whether the luminaire has been damaged during transport. Do not operate/install any product which appears damaged in any way. Return the complete product to the place of purchase for inspection, repair or replacement.
-
Ensure power to the circuit you are working on has been switched OFF before commencing any electrical work.
Installation Directions
-
Remove all packaging material from the product and be careful not to throw away accessories that may be hidden within the packaging material. If assembly is required, place the luminaire on a smooth non-scratch surface.
-
Determine the suspension length required for your installation by loosening the cord anchorage (F) and adjusting the length of the suspension cord (H). Tighten the cord anchorage (F), take care not to overtighten and damage the cord.
-
Remove the mounting bracket (B) from the canopy (E) by loosening the screws (D) on the side.
-
Use the mounting bracket (B) as a template to mark the screw positions on the ceiling.
-
Install the mounting bracket (B) onto the ceiling by using appropriately sized mounting screws (C) and anchors (A). Ensure the screws (C) and anchors (A) used are suitable for the mounting surface and the surrounding environment.
-
Connect the mains supply wire to the terminal block (G). Ensure the wires are secure and no bare wires are exposed.
Mains Supply Wire
Earth – Yellow/Green
Neutral – Blue or Black
Live – Brown or Red
Luminaire Wire / Terminal Block
Yellow/Green or
Blue or N
Brown or L -
Install the canopy (E) onto the mounting bracket (B) and secure by tightening the screws (D) on the side.
-
Remove the shade (K) from the lamp holder (I) by twisting it anti-clockwise.
-
Install the included LED lamp (J) into the lamp holder (I). Do not exceed the maximum wattage rating.
NOTE: This luminaire is suitable for use with LED lamps only.
Compatible with G9 LED lamps of 28mm or smaller.
SKU# 121350 / SKU# 121351 G9 lamps are recommended. -
Install the shade (K) back onto the lamp holder (I) by twisting it clockwise.
-
After the installation, switch on the luminaire to test and enjoy your new lighting product.
Safety Tips
- Always ensure the power is OFF and the luminaire has cooled down before performing any maintenance, cleaning, changing the globe or making any adjustment to the luminaire.
- To avoid injury or damage to the luminaire, ensure that power leads and screws are secure before connecting the power.
- Select a suitable location away from liquids and hazards.
- To clean, wipe with a soft damp cloth. Do NOT soak or immerse the luminaire in water or other liquids.
- Ensure that the luminaire does not come in contact with corrosive chemicals/solvents or abrasive cleaners etc.
Specifications
Specifications
SKU #| 050649
Rated Voltage| 220-240V~ 50Hz
Rated Wattage| Max. 11.5W * (5 x 2.3W Max.)
(LED lamps only)
Lamp Holder| G9
Weight| 2.6kg
Canopy Dimensions| H:25mm Dia:250mm
Luminaire Dimensions| H:700mm Dia:250mm Susp:2000mm MAX
NOTE: Compatible with G9 LED lamps of 28mm or smaller.
SKU# 121350 / SKU# 121351 G9 lamps are recommended. This luminaire is suitable
for use with LED lamps only.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>