JBL COL800 COL Column Speaker Installation Guide

COL Column Speaker

Installation Guide

Included Hardware

(not to scale)

| 3 pieces M6 x 12 mm bolts with flat washers & lock washers
3 pieces M6 x 20 mm bolts with flat washers & lock washers
3 pieces M6 x 28 mm bolts with flat washers & lock washers
(Note: Flat washers & lock washers are captive on the bolts.
One additional of each bolt is provided for backup.)
4 mm hex key
---|---
| 2-part Low- Profile Swivel (Pan) / Tilt WALL BRACKET ASSEMBLY Consists of:
• SPEAKER-SIDE of Bracket
• WALL-SIDE of Bracket
• Decorative Trim piece for WALL-SIDE BRACKET (not shown)
| 2 pieces L-BRACKETS
| TRIM COVER (for WALL BRACKET ASSEMBLY)

Important Safety Instructions

1. Please read and keep all safety and user instructions.

2. This product is intended for installation by professional installers only! This document is intended to provide professional installers with basic installation and safety guidelines for this product in typical fixed-installation systems. Please read this document  and all safety warnings before attempting installation. Do not attempt to service this product yourself.
   Refer all servicing to authorized service centers, installers, technicians, dealers or distributors. To contact Harman Professional or to find a dealer or distributor near you, visit https://www.jblpro.com.

3. The products must be installed in accordance with local, state, federal and industry regulations. It is the installer’s responsibility to ensure installation of the loudspeakers and mounting system is performed in accordance with all applicable codes,  including local building codes and regulations. Consult the local authority having jurisdiction before installing this product.

4. Unsafe mounting or overhead suspension of any heavy load can result in serious injury or death, and property damage.
   It is the installer’s responsibility to evaluate the reliability of any mounting method used for their application. Only professional installers with the knowledge of proper hardware and safe mounting techniques should attempt to install any loudspeaker  overhead.

5. Do NOT make unauthorized alterations to this product.

6. Only use the mounting hardware supplied with this product.

7. Do not mount on surfaces that are not sturdy, or that have hazards concealed behind them, such as electrical wiring or plumbing. If you are not sure about installing the bracket, contact a qualified professional installer. Ensure the bracket is installed  according to local building codes.

8. Do not use hydrocarbon based solvents, lubricants or cleaning agents of any type on or around this speaker, and associated mounting hardware, during installation. The use of such hydrocarbon based lubricants, solvents or cleaning agents on or around the  mounting anchors and screws can lead to degradation of the plastic material, possibly resulting in cracking and premature failure of the product.

9. Keep the product away from fire and heat sources. Do NOT place naked flame sources, such as lighted candles, on or near the product.

10. The loudspeaker and all mounting components must be inspected annually by a qualified professional who is trained and certified in suspending loudspeaker systems. All rigging parts and components used in the suspension of the loudspeaker system should be visually inspected for signs of cracking, bending, water damage, corrosion, de-lamination, or any other condition that could compromise the system’s integrity and create a dangerous falling hazard.

11. Prolonged exposure to excessive SPL can cause hearing damage! The loudspeaker is easily capable of generating sound pressure levels (SPL) sufficient to cause permanent hearing damage to performers, production crew, and audience members. Caution should be taken to avoid prolonged exposure to SPL in excess of 90 db.

WATCH FOR THIS SYMBOL:
The exclamation point, within an equilateral triangle, is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.
WARNING: No naked flame sources – such as lighted candles – should be placed on the product.
CAUTION: To be installed by instructed, or skilled, persons only.

Regulatory Information

This product conforms to all applicable EU directive requirements. The full text of the EU declaration of conformity is available at the following internet address: https://www.jblpro.com
This product conforms to all applicable Electromagnetic Compatibility Regulations 2016 and all other applicable UK regulations. The complete declaration of conformity can be found at: https://www.jblpro.com
This symbol means the product must not be discarded as household waste, and should be delivered to an appropriate collection facility for recycling. Proper disposal and recycling helps protect natural resources, human health and the environment. For more  information on disposal and recycling of this product, contact your local municipality, disposal service, or the shop where you bought this product.
CAUTION: Installation must be done by skilled persons using safe installation standards.
The COL speaker can be attached to the wall either using the included SWIVEL/TILT WALL BRACKET or using the two included LBRACKETS.

OPTION A: WALL SURFACE MOUNTING VIA **INCLUDED SWIVEL/TILT WALL

BRACKET
**

Note that the BRACKET ASSEMBLY consists of a SPEAKER-SIDE and a WALL- SIDE.
1.0) Mounting WALL-SIDE BRACKET:
1.1) Run the wiring from the power amplifier to the location desired for mounting the JBL COL loudspeaker.
1.2) Secure WALL-SIDE BRACKET to wall using the appropriate installer-selected attachment hardware, and using a level to ensure that the WALL-SIDE BRACKET is straight. Use both screw holes of WALL-SIDE BRACKET. Be sure that the TILT-SET SLOT is  at the top and HOOK SLOT is at the bottom. After attaching to the wall, slide plastic TRIM COVER over bracket and snug to wall.

Hardware for attaching WALL SIDE of Bracket to wall is not included. The installer is responsible for proper selection and use of mounting hardware and for properly and safely securing the bracket to the wall material.

2.0) Mounting SPEAKER-SIDE BRACKET to COL speaker:
2.1) Identify the COL speaker’s two back panel mounting points, labeled on the back panel as “WALL BRACKET POINTS”.
Remove the silicone caps from those points, exposing the threaded inserts.
2.2) Attach the 2-part SPEAKER-SIDE BRACKET to COL speaker using two M6 x 20 mm bolts (with flat washers and lock washers). Recommended –– 3.5 N•
m [+0.5/-0] (2.6 ft-lb [+0.4/-0]).

Remove Silicon Caps
Insert M6 x 20 mm Bolts with Flat Washers & Lock Washers

3.0) Connecting SPEAKER-SIDE BRACKET to WALL-SIDE BRACKET to form SWIVEL/TILT BRACKET ASSEMBLY:
3.1) After sliding TRIM COVER onto WALL-SIDE BRACKET, loosely thread one of the M6 x 12 mm bolts (with flat washer and lock washer) into the bottom PIVOT hole of the SPEAKER-SIDE BRACKET. This bolt becomes the PIVOT BOLT.
3.2) Slide COL speaker (with SPEAKER-SIDE BRACKET attached) onto the WALL-SIDE BRACKET, sliding the PIVOT BOLT into the HOOK SLOT of the WALL-SIDE BRACKET. Make sure the flat washer and lock washer are on the same side of the WALL- SIDE BRACKET as the bolt’s head (and aren’t caught between the two brackets).

3.3) After the column is being held in place by the PIVOT BOLT, insert the other M6 x 12 mm bolt (with flat washer and lock washer) through the TILT-SET SLOT and thread it into the press-fit nut that’s part of the SPEAKER-SIDE BRACKET.
3.4) With both bolts now engaged, tighten them. [Recommended torque 3.5 N• m [+0.5/-0] (2.6 ft-lb [+0.4/-0]).
3.5) To set a down-tilt aiming angle, loosen both bolts slightly, adjust the tilt of the speaker, and re-tighten the bolts.
3.6) To set the swivel (pan), loosen the bolts at the top and bottom of the SWIVEL JOINT, set the swivel (pan), and re-tighten the bolts.

SWIVEL (PAN) / TILT WALL BRACKET ASSEMBLY Dimensions and Settings

OPTION B: WALL SURFACE MOUNTING VIA INCLUDED L-BRACKETS

Note that the L-BRACKETS can be attached to either the top and bottom of the speaker (via threaded inserts located on the top and bottom panels) or to the sides of the speaker (via threaded inserts located in the left and right panels of the speaker). The following instructions and drawings are for using the side points.

L-BRACKET Dimensions

4.0) Install L-BRACKETS to the Wall and Side Insert Points:
4.1) Run the wiring from the power amplifier to the location desired for mounting the JBL COL loudspeaker.
4.2) Secure L-BRACKET to wall using the appropriate installer-selected attachment hardware, and using a level to ensure that the L-BRACKETS are plumb. Use 3 screws for each L-bracket. For use with side insert points, space brackets so that innermost screws holes are 25 mm apart (adjust as needed).
CAUTION: Installation must be done by skilled persons using safe installation standards.

Hardware for attaching L-BRACKETS to wall is not included. The installer is responsible for proper selection and use of mounting hardware and for properly and safely securing the brackets to the wall material.
If precipitation can be present at the installation location, cabinet must not be installed at any upward aim angle, and slight downward aim angle (5° or greater) is recommended to keep water out of loudspeaker.
4.3) Remove the silicone caps from over the left-side and right-side threaded insert points, exposing the metal threaded inserts.
Note: There are two holes in the column-end part of each L-BRACKET – one for situating the column closest to the wall and one for spacing farther out from the wall. Select the hole to meet with desired distance from the wall (for example, clearance for cables, or keeping entire distance from the wall below 4 inches in order to comply with ADA).

4.4) Use the M6 x 20 mm bolts through the L-BRACKETS and tighten into threaded inserts. Recommended torque 3.5 N•m [+0.5/-0] (2.6 ft-lb [+0.4/-0]).

5.0) Installing L-BRACKETS to the Wall and TOP/Bottom Insert Points:
5.1) Apply same process from 4.1 and 4.2 for running wiring and attaching L-brackets to wall. For use with top and bottom insert points, space brackets so that inner-most screws holes of the L-BRACKETS (wall side) are the following distances apart:

Distance Between Innermost Screws

Hardware for attaching L-BRACKETS to wall is not included. The installer is responsible for proper selection and use of mounting hardware and for properly and safely securing the brackets to the wall material.
5.2) Remove the silicone caps from over the top and bottom threaded insert points and remove the bolts that are holding the end caps, exposing the inserts (these removed bolts will not be re-used).
Note: There are two holes in the column-end part of each L-BRACKET. For the top and bottom points on the speaker, the outer-most BRACKET hole must be used.

4.3) Use the M6 x 28 mm bolts through the L-BRACKETS, swivel aiming of the speaker (if desired), and tighten the bolts.
Recommended 3.5 N.m +0.5/-0 N.m (2.6 ft-lb +0.4/-0)

COMPLETING THE INSTALLATION

6.0) SECONDARY SAFETY CABLE — Attach a properly load-rated safety cable (not included) to the back-panel M6 threaded insert point on the back panel marked “Safety Cable,” using hardware that does not incur interference with the wall. Attach the other  end of the safety cable to a secure independent attachment point on the building structure. Keep the safety cable as short as possible without pulling on the cabinet or ratting against the cabinet.

7.0 WIRING THE SPEAKER
7.1 – Select proper gauge speaker cable. Utilize a reliable reference to select the proper gauge speaker cable, keeping in mind the total number of speakers that may be looped in the circuit run, and what their tap settings are. Maximum outside diameter of cable is 8.0 mm (0.31 in).
7.2 – Included 4-pin pluggable terminal connector – Connect wires securely to in-line terminal connector.
Terminals – The 4-pin Autoblock connection for bare wire and includes pins for

• and – input and for + and – loop out.
  Accepts 20 to 14 gauge wire (0.25 to 2.5 sq. mm).

7.3 TERMINAL COVER – Remove the TERMINAL COVER, plug in-line terminal connector into chassis socket. Run wire(s) downward and re-attach terminal cover using 3 included screws, making sure pressure insert (for resistance against water ingress) presses down on wires. The TERMINAL COVER may be left off if no resistance against water is needed.

8.0 REFERENCE
8.1 GUIDE: Maximum Speakers Per Circuit Run – For systems where the wiring is looped through to subsequent speakers, the terminals support a maximum of 20 Amps of current for the input plus the loop out. As long as the cable gauge is large enough to  support the current, the following chart shows the maximum number of speakers per cable run that the terminals support, based on: a) whether the speakers are set to low-impedance (8Ω) or highimpedance (i.e., set at a Tap), and b) if high impedance, what Tap the speakers are set at.

Notes:

1. The speaker cable gauge needs to also be able to support the number of speakers connected in looped-out circuit.
2. For combinations of tap settings, system designer must compute the total current draw and ensure that it stays under 20A.
3. Total impedance must stay above the minimum impedance capability of amp channel.
4. Total power connected must be below the maximum power capability of amp channel.

COL600
Low-Impedance (8Ω) – Maximum 6 speakers
20W Tap – Maximum 70 speakers
10W Tap – Maximum 141 speakers
5W Tap – Maximum 282 speakers
2.5W Tap (70V only) – Maximum 564 speakers

COL800
Low-Impedance (8Ω) – Maximum 4 speakers
60W Tap – Maximum 23 speakers
30W Tap – Maximum 47 speakers
15W Tap – Maximum 94 speakers
7.5W Tap (70V only) – Maximum 188 speakers

8.1 GUIDE: Back Panel Drawings

8.2 GUIDE: Dimensions

8.3 GUIDE: Down-Tilt Aiming and Coverage – The COL speakers incorporate a 10° downward tilt to dispersion aim, allowing for coverage of most listening areas without requiring physical down-tilting of the cabinet:

COL 800
60° total vertical coverage angle with aiming axis at -10°| COL 600
110° total vertical coverage angle with aiming axis at -10°

JBL Professional 8500 Balboa Blvd.
Northridge, CA 91329
COL Install Guide
05/2023

Documents / Resources

| JBL COL800 COL Column Speaker [pdf] Installation Guide
COL 800, JBL-COL800-BK, JBL-COL800-WH, COL 600, JBL-COL600-BK, JBL-COL600-WH, COL800 Slim Column Loudspeaker, COL800, Slim Column Loudspeaker, Loudspeaker, COL800 COL Column Speaker, COL Column Speaker, Column Speaker
---|---

References

• JBL Professional Loudspeakers | English (US)
• JBL Professional Loudspeakers | English (US)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>