F2 Medical TF4 Endodontic Files Instructions

June 13, 2024
F2 Medical

F2 Medical TF4 Endodontic Files

Product Information

The product is called To & Fro PLUS Endodontic Files (TF4) WaveOneGold Compatible EndoFiles. These files are reciprocating, single-file system used for endodontic procedures. They are  heat-treated and made from gold NiTi using advanced metallurgy,which enhances flexibility.
The product comes in four sizes: #20/.07 Taper, #25/.07 Taper, #35/.06 Taper, and #45/.05 Taper.

Product Usage Instructions

  1. Establish straight-line coronal and radicular access.
  2. In the presence of a viscous chelator, use a size #10 hand file to verify a glide path to length. In more restrictive canals, use asize #10 hand file in any region of a canal to create a glide path.
  3. Expand this glide path to at least 0.15mm using either a manual or dedicated mechanical file, such as ET Files or the dedicated TF4 File.
  4. Always initiate the shaping procedure with the PRIMARY file (#25/.07 Red) in the presence of sodium hypochlorite.
  5. Use gentle inward pressure and let the PRIMARY file passively progress through any region of the canal that has a confirmed glide path.
  6. After shaping 2-3mm of any given canal, remove and clean the PRIMARY file, then irrigate, recapitulate with a size #10 hand file, and re-irrigate.
  7. Continue with the PRIMARY file in 2-3 passes to pre-enlarge the coronal two-thirds of the canal.
  8. Utilize a brushing motion on the outstroke to eliminate coronal interferences or to enhance shaping results in canals that exhibit irregular cross-sections.
  9. In more restrictive canals, use a size #10 hand file, in the presence of a viscous chelator, negotiate to the terminus of the canal.
  10. Gently work this file until it is completely loose at length. Establish working length, confirm patency, and verify the glide path.
  11. Expand this glide path to at least 0.15mm using a manual or mechanical glide path file.
  12. Carry the PRIMARY file to the full working length in one or more passes.
  13. Upon reaching length, remove the file to avoid over-enlarging the foramen.
  14. Inspect the apical flutes. If they are loaded with dental debris, then the shaping is finished.
  15. If the PRIMARY file doesn’t progress, then use the SMALL file (#20/.07 Yellow) in one or more passes to working length and then use the PRIMARY file to working length to optimize the shape.
  16. When the shape is confirmed, proceed with 3-D disinfection protocols.
  17. If the PRIMARY file is loose at length with no dental debris inthe apical flutes, continue shaping with MEDIUM file (#35/.06 Green) and/or LARGE file (#45/.05 White) until the apical flutes are loaded.

Specification

  • Material: NiTi
  • Sterilization: ≤126°C
  • Assorted/Single size
  • Colour: Gold
  • Rotary Speed: 350 Rpm
  • Torque: 2.0 – 3.0 N/cm
  • Length: 21mm/25mm/31mm
  • Standard: CE/ISO/FDA/FSCF2-Medical-TF4-Endodontic-Files-fig

Recommended Operation Sequence

  • Establish straight-line coronal and radicular access.
  • In the presence of a viscous chelator, use a size #10 hand file to verify a glide path to length. In more restrictive canals, use a size #10 hand file in any region of a canal to create a glide path.
  • Expand this glide path to at least 0.15 mm using either a manual or dedicated mechanical file, such as ET Files or the dedicated TF4 File.
  • Always initiate the shaping procedure with the PRIMARY file (#25/.07 Red) in the presence of sodium hypochlorit.
  • Use gentle inward pressure and let the PRIMARY file passively progress through any region of the canal that has a confirmed glide path.
  • After shaping 2-3 mm of any given canal, remove and clean the PRIMARY file, then irrigate, recapitulate with a size #10 hand file and re-irrigate.
  • Continue with the PRIMARY file, in 2-3 passes, to pre-enlarge the coronal two thirds of the canal.
  • Utilize a brushing motion on the outstroke to eliminate coronal interferences or to enhance shaping results in canals that exhibit irregular cross-sec?ons.
  • In more restrictive canals, use a size #10 hand file, in the presence of viscous chelator, negotiate to the terminus of the canal.
  • Gently work this file until it is completely loose at length.
  • Establish working length, confirm patency and verify the glide path.
  • Expand this glide path to at least 0.15 mm using a manual or mechanical glide path file.
  • Carry the PRIMARY file to the full working length in one or more passes.
  • Upon reaching length, remove the file to avoid over-enlarging the foramen.
  • Inspect the apical flutes, if they are loaded with dentinal debris, then the shape is finished.
  • If the PRIMARY doesn’t progress then use the SMALL file (#20/.07 Yellow) in one or more passes to working length and then use the PRIMARY file to working length to optimize the shape.
  • When the shape is confirmed, proceed with 3-D disinfection protocols.
  • If the PRIMARY file is loose at length with no dentinal debris in the apical flutes, continue shaping with MEDIUM file (#35/.06 Green) and/or LARGE file (#45/05 White) until the apical flutes are loaded.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals