SURAIELEC C1XByDZL-ML Wireless Light Switch and Receiver Kit User Manual
- October 30, 2023
- SURAIELEC
Table of Contents
SURAIELEC C1XByDZL-ML Wireless Light Switch and Receiver Kit User Manual
♦ Warning: To reduce the risk of fire, electric shock or personal injury, please strictly follow the instructions.
- Always be sure to cut off the power before installing the receiver.
- Do not connect any devices that may exceed the performance limits of the receiver kit.
- Do not disassemble or repair the product, but only by authorized service personnel.
- To prevent children from suffocation and choking, keep them away from packing materials.
- Do not dispose of any part of this product in a fire.
- Avoid exposing to high-temperature sources and areas with a high magnetic field.
- If the remote is not in use for an extended period of time, remove the battery.
- Used batteries should be in accordance with local environment regulations. Do not dispose in regular household waste.
- Any questions or accessories inquiry, please contact us first by E-mail: surai-tech@outlook.com
Product Layout
Receiver Mounting
- Behind a light fixture
- Install at a switch local
- Mounting on a junction box
NOTE:
The RF wireless range will be shortened by electronic devices, walls, or other
physical barriers, especially metal objects.
Avoid placing the receiver into or behind the metal objects.
Wiring Diagram
-
TO AVOID ELECTRIC SHOCK; TURN OFF POWER at circuit breaker or fuse and test that power is off before wiring!
-
Connect wires per WIRING DIAGRAM
“BLACK”=LINE(Supply In) “RED”=LOAD Supply Out) “WHITE”=NEUTRIAL -
Remove the isolation tab in the battery compartment of the transmitter.
-
Press the ON or OFF button on the transmitter will turn on or off the corresponding accordingly.
Transmitter Installation
Hand held or wall mount
Reset a Receiver
To remove a receiver from all remote control pairings which means that the receiver can’t be controlled by any transmitter.
- Press and hold the program ON/OFF button on the switch receiver for about 6 seconds until the LED indicator begins to fast flash.
- When the LED indicator flashes from slowly to rapidly, release the program button and press again. The indicator light will be off and the program has been cancelled.
Programming
The transmitter and light switch kit receiver have been pre-paired for immediate use, but there are a few units are not pre-programmed or programmed incorrectly, or you want to change the pre-set configuration to meet your needs. To program a transmitter and receiver, please follow the steps below:
- Cancel the programming referring to the above “Rest a Receiver” section firstly
- Turn the power on for the wire switch receiver.
- Press and hold the program ON/OFF button on the wire switch receiver for about 3 seconds until the LED indicator begins to flash slowly.
- Release the program button and then press the “on” or “off” button on the remote control.
- Program is successful when the LED indicator stops flashing.
Troubleshooting
In the case that one light switch kit receiver is unresponsive to a remote transmitter, follow the steps below to resolve the issue:
-
Make sue the light switch kit receiver and device are properly connected and powered on.
-
Make sure not exceed the maximum load 15A.
-
Replace the remote batteries with new 12V (23A type) Alkaline batteries.
Low battery power may decrease readable wireless remote range. -
Remove the battery isolation tab in the battery compartment of the transmitter, check if the polarity +/- of the battery in transmitter is correct.
-
Please refer to the ” Reset an Receiver” and ” Programming” operation sections in the manual.
-
“Reset an Receiver” is always prior to ” Programming” operation when you want to make some changes.
Suraielec Remote Series Product
To meet your different needs, suraielec provides all series of remote products. All of them can be paired freely.
Specifications
Power Supply: 125VAC/ 60Hz
Max. Rating: 15A /1875W( Resistive ), 1 0A/ 1250W ( Tungsten ),
BA/ 1 000W ( Fluorescent ), 200W (LED)
Frequency: 433.92MHz
Battery: 12V 23A (included)
Package Includes
Receiver x 1
Remote Transmitter x 1 (URKW11 C); Remote Transmitter x 2 (URKW21 C)
Mount Screws x 1 set
Instruction Manual x 1
One Year Limited Warranty
Suraielec warrants this product to be free from defects in material and
workmanship for a period of one year from the date of purchase.
Warranty is void if damage is caused by misuse or improper installation.
Email: surai-tech@outlook.com
Our dedicated customer service team will get back to you within 24 hours.
This device complies with part 15 of the FCC rules.
Operation is subject to the following two conditions:
(1) This device may not harmful interference, and
(2) this device must accept any interference received, including interference
that may cause undesired operation.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>