BOSCH 020726 Built-Under Hob Instruction Manual
- October 30, 2023
- Bosch
Table of Contents
BOSCH 020726 Built-Under Hob
Product Information
The text extract is a user manual for a kitchen appliance with a product code of 9000750994. The manual provides installation instructions in multiple languages, including German, Spanish, English, Greek, French, Swedish, Italian, Finnish, Norwegian, Russian, Danish, Czech, Dutch, Turkish and Polish. The manual includes information on safe installation, intermediate floor, preparing the units, inserting the hob into the wider cut-out, installing fixing rails, electrical connection and removing the hob.
Product Usage Instructions
Before installing the appliance, create wooden battens in accordance with the drawing and screw them in place so that they are flush with the upper edge of the worktop. For stone work surfaces, bond the wooden battens in place. Check and adjust the cut-out dimensions before inserting the hob into the wider cut- out. Install fixing rails for a cut-out with a depth of 500 mm. For electrical connection, ensure that the appliance is not removed from the polystyrene trays until it is pressed into the cut-out. Do not lay the appliance down flat on its side. The appliance is class I and must only be operated in conjunction with an earth conductor. A Trennvorrichtung must be provided in the phases in accordance with the installation regulations. To install the hob, disconnect the appliance from the power supply and push out the hob from below. To remove the hob, disconnect the appliance from the power supply and push out the hob from below.
Safe installation
Follow these safety instructions when installing the appliance.
- Electrical connection must only be carried out by licensed specialist staff. Incorrect connection will invalidate the warranty.
- The safe operation of this appliance can only be guaranteed if it has been installed to a professional standard in accordance with these installation instructions. The installer shall be liable for any damage resulting from incorrect installation.
Built-under
Do not install refrigerators, dishwashers, non-ventilated ovens or washing
machines underneath the appliance.
- If you fit a modular or compact dishwasher of the same brand underneath the appliance, the worktop must be at least 40 mm thick.
- If you fit an oven below the appliance, the worktop must be at least 20 mm thick, in certain cases even thicker. Observe the information in the oven installation instructions.
- Make sure that projecting parts such as the mains housing or the mains cable do not collide, e.g. with a drawer.
Intermediate floor
If the underside of the hob can be touched, an intermediate floor must be
fitted.
- Ask your specialist retailer for an intermediate floor as an accessory.
- If you use your own intermediate floor, the minimum distance to the mains connection of the appliance must be 10 mm.
Preparing the units
The worktop must be level, horizontal and stable.
- The fitted units, including wall finishing strips, must be heat-resistant to at least 90 °C.
- Niche cladding within 50 mm of the back wall must not be combustible (e.g. tiles, stone).
- Seal the cut surfaces to make them heat-resistant. This prevents the worktop from swelling as a result of moisture. → Fig. 1
Inserting the hob into the wider cut-out
- Create the wooden battens in accordance with the drawing.
- Check and adjust the cut-out dimensions.
- Screw the wooden battens in place so that they are flush with the upper edge of the worktop. For stone work surfaces, bond the wooden battens in place. → Fig. 2 , → Fig. 3
Installing fixing rails
For stone work surfaces, bond the fixing rails in place.
- The hob can also be installed in an existing cutout that has a depth of 500 mm. → Fig. 4
Electrical connection
To protect the appliance, do not remove it from the polystyrene trays until you press the appliance into the cut-out. Never lay the appliance down flat on its side.
- Check the household wiring before connecting the appliance.
- The appliance fulfils the requirements of protection class I and must only be operated in conjunction with an earth conductor.
- In the permanent electrical installation, a partition must be provided in the phases in accordance with the installation regulations.
- If U400 appears on the appliance’s display, it has not been connected correctly. Disconnect the appliance from the mains and check the connection.
Connecting without a pre-installed cable
Only connect the hob in accordance with the connection diagram.
- If required, install the enclosed copper bridges.
- The power cable must correspond to type H05 VV-F or a higher rating.
- Use the current load to determine which wire cross-section you require. A cross-section of < 1.5 mm² is not permitted.
Installing the hob
Do not trap the power cable and do not route it over sharp edges.
- If the oven is a built-under type, route the cable along the rear corners of the oven to the mains socket.
- Push the hob in until it locks into place. → Fig. 5
Removing the hob
- Disconnect the appliance from the power supply.
- Push out the hob from below.