BOSCH HBF534ES0Q Built-Under Oven Instruction Manual

October 30, 2023
Bosch

BOSCH-LOGO

BOSCH HBF534ES0Q Built-Under Oven

BOSCH-HBF534ES0Q-Built-Under-Oven-PRODUCT

Product Information

The user manual provides information and instructions for the installation of an appliance, likely a cooktop or stove. The product is designed to be built under a countertop or work surface and requires fixing rails to be installed to secure it in place. The appliance must be connected to an earth conductor and the installation must comply with relevant regulations. The user manual provides instructions for preparing the furniture, installing the fixing rails, and connecting the appliance to the electrical supply. The manual also includes instructions for inserting and removing the cooktop.

Product Usage Instructions

  1.  Prepare the furniture to ensure that there is a minimum distance of 10mm between the appliance and the electrical connection.
  2. Install fixing rails to secure the appliance in place. For stone work surfaces, bond the fixing rails in place.
  3. Connect the appliance to an earth conductor in compliance with relevant regulations.
  4. Insert the cooktop into the prepared space. To protect the appliance, do not remove it from the polystyrene trays until you press the appliance into the cut-out. Never lay the appliance down flat on its side.
  5. To remove the cooktop, disconnect the appliance from the power supply and push out the hob from below.

Safe installation

Follow these safety instructions when installing the appliance.

  • Electrical connection must only be carried out by licensed specialist staff. An incorrect connection will invalidate the warranty.
  • The safe operation of this appliance can only be guaranteed if it has been installed to a professional standard in accordance with these installation instructions. The installer shall be liable for any damage resulting from incorrect installation.

Built-under
Do not install refrigerators, dishwashers, non-ventilated ovens or washing machines underneath the appliance.

  • If you fit a modular or compact dishwasher of the same brand underneath the appliance, the worktop must be at least 40 mm thick.
  • Make sure that projecting parts such as the mains housing or the mains cable do not collide, e.g. with a drawer.

Intermediate floor
If the underside of the hob can be touched, an intermediate floor must be fitted.

  • If you use your own intermediate floor, the minimum distance to the mains connection of the appliance must be 10 mm.

Preparing the units

The worktop must be level, horizontal and stable.

  • The fitted units, including wall finishing strips, must be heat-resistant to at least 90 °C.
  • Niche cladding within 50 mm of the back wall must not be combustible (e.g. tiles, stone).
  • Seal the cut surfaces to make them heat-resistant. This prevents the worktop from swelling as a result of moisture. → Fig. 1BOSCH-HBF534ES0Q-Built-Under-Oven-FIG-1
  • Installing fixing rails For stone work surfaces, bond the fixing rails in place. → Fig. 2

Electrical connection

To protect the appliance, do not remove it from the polystyrene trays until you press the appliance into the cut-out. Never lay the appliance down flat on its side.

  • Check the household wiring before connecting the appliance.
  • The appliance fulfills the requirements of protection class I and must only be operated in conjunction with an earth conductor.
  • In the permanent electrical installation, a partition must be provided in the phases in accordance with the installation regulations.
  • If appears on the appliance’s display, it has not been connected correctly. Disconnect the appliance from the mains and check the connection. Connecting without a pre-installed cable Only connect the hob in accordance with the connection diagram.
  • If required, install the enclosed copper bridges.
  • The power cable must correspond to type H05 VV-F or a higher rating.
  • Use the current load to determine which wire cross-section you require. A cross-section of < 1.5 mm² is not permitted.

Installing the hob

Do not trap the power cable and do not route it over sharp edges.

  • If the oven is a built-under type, route the cable along the rear corners of the oven to the main socket.
  • Push the hob in until it locks into place. → Fig. 3

Removing the hob

  1. Disconnect the appliance from the power supply.
  2. Push out the hob from below.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals