RYOBI Tools RYRM8001 80V HP Brushless 30 Inch Battery Electric Cordless Zero Turn Riding Mower User Guide

Tools RYRM8001 80V HP Brushless 30
Inch Battery Electric Cordless Zero Turn Riding Mower
ASSEMBLY GUIDE
GUIDE D’ASSEMBLAGE
User Guidehttp://register.ryobitools.com

RYRM8001 80V HP Brushless 30 Inch Battery Electric Cordless Zero Turn

Riding Mower

http://scn.by/hf64rqsvadp8y0
Scan the QR Code to view an instructional video.

Follow all instructions when assembling this riding lawn mower. If any parts are damaged or missing, those parts must be replaced before proceeding.
WARNING: To reduce the risk of injury, you must read and understand this assembly guide before attempting to assemble this product.
SAVE THIS GUIDE FOR FUTURE REFERENCE

RULES FOR SAFE ASSEMBLY

**WARNING:**
Strictly adhere to all torque wrench tightening specifications. Failure to do so could cause serious personal injury.
All information, illustrations, photographs, and specificationscontained in this manual are based on the latest product information available at the time of publication. Due to updates or other changes, there may be some differences in this manual. We reserve the right to make product changes at any time, without notice and without incurring any obligation to make the same or similar changes to any products previously built or sold.

• Any person attempting to assemble this product must have proper training and experience. Read this manual carefully and follow all assembly procedures as described.
• All assembly must be completed with the unit on a level surface.

SYMBOLS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

will result in death or serious injury.
**| WARNING:| Indicates a hazardous situation, which, if not avoided, could result in death or serious injury.
**| CAUTION:| Indicates a hazardous situation, that, if not avoided, may result in minor or moderate injury.
| NOTICE:| (Without Safety Alert Symbol) Indicates information considered important, but not related to a potential injury (e.g. messages relating to property damage).

Some of the following symbols may be used on this product. Please study them and learn their meaning. Proper interpretation of these symbols will allow you to operate the product better and safer.

TOOLS NEEDED

The following tools (not included or drawn to scale) are needed for assembly:

UNPACKING

• Remove the bolts securing the corner and side braces to the frame bottom, then lift the braces to remove.
• Cut the nylon straps securing the front and rear wheel axles to the frame.
• Remove boxes containing loose parts, assembly hardware, and documentation.
• Remove and set aside all accessible packaging and wrap from unit and parts. Do not discard the packing material until you have carefully inspected and satisfactorily operated the product.

**WARNING:**
If any parts on the Loose Parts List are already assembled to your product when you unpack it, verify the part is assembled correctly, is properly tightened, and is torqued correctly (where applicable) before proceeding to the next assembly step. Use of a product that may have been improperly assembled could result in death or serious personal injury.

• Inspect the product carefully to make sure no breakage or damage occurred during shipping.
• If any parts are damaged or missing, please call 1-800-525-2579 for assistance.

NOTE: Mower should be assembled while positioned on the frame bottom. Once assembly is complete, raise the cutting deck to its highest position, position a ramp next to the frame bottom, release the parking brake and slowly and carefully drive mower off frame.
WARNING:
Use extra care when driving the mower off of the frame. Press the low speed drive button and carefully move the joystick and/or press the brake pedal as needed to control the speed. When driving the mower off of the frame, do not exceed the maximum recommended operation angle of 15°. Failure to follow these instructions can result in loss of control and result in death, serious personal injury, or property damage.
NOTICE:
If no ramp is available, slowly and carefully drive the mower off the frame in reverse while looking down and behind. Driving the mower off the frame in the forward direction without a ramp can cause damage to the mower’s cutting deck.

http://scn.by/hf64rqsvadp8y0

LOOSE PARTS LIST

Key

Joystick
Dust cover
Hex screws| 1
1
2
3| Charger| 1
4| Seat Assembly| 1
5| Tool Bag| 1
6| Keys
Assembly Guide (Not Shown)
Operator’s Manual (Not Shown)| 3
1
1

**WARNING:**
If any parts are damaged or missing do not assemble this product until the parts are replaced with new original manufacturer’s parts or their equivalent. Assembly of this product with damaged, missing, or incorrect parts could result in serious personal injury.

ASSEMBLY

WARNING:
Strictly adhere to all torque wrench tightening specifications. Failure to do so could cause serious personal injury.
WARNING:
Do not attempt to modify this product or create accessories not recommended for use with this product. Any such alteration or modification is misuse and could result in a hazardous condition leading to possible serious personal injury.
WARNING:
To prevent accidental starting that could cause serious personal injury, always remove the start key from the tool when you are assembling parts.

INSTALL THE SEAT
See Figure 1.

• Place the seat assembly over the mounting brackets and align as shown.
• Lower the seat clip so it is secured onto the mounting bracket.
• Attach the seat safety interlock cable to the plug on the mower.
• Attach the carabiner clips as shown.
• Lower the seat.

INSTALL THE JOYSTICK
See Figure 2.

• Insert the joystick through the dust cover as shown.
• Align the holes on the joystick to the holes on the mounting shaft.
• Insert the hex screws and tighten securely with the included hex key.
• Align the tabs on the dust cover with the base and press down to lock the dust cover into place.

CONNECTING THE 80V BATTERIES
See Figures 3. – 4
When shipped from the factory, the mower’s batteries are disconnected.
To connect:

• Place the joystick in the neutral and locked position. (See Learning to Drive the Mower in the Operation section of the operator’s manual.)

• Adjust the seat all the way forward.

• Press the center edge on the battery compartment cover to release the latch. The cover will raise to gain access to the compartment below.

• Install the battery pack’s quick-connect plugs. This plug connects the batteries to the mower.
  NOTE: Be sure each battery latch is locked to secure the batteries.

• Lower the lid to the battery compartment and press on the center edge to engage the lock.
  NOTE: Make sure the battery compartment cover is securely locked before readjusting the seat. Check to be sure the safety interlock cable is still connected.

FINAL PREPARATION

CHECK TIRE PRESSURE
Check the air pressure in all tires before use. Improper air pressure will affect handling, steering response, traction, tire life, level cutting, and operator comfort. Be sure tires are inflated to the pressure shown below.
NOTE: Tire pressure should only be measured or adjusted when tires are cold.

WARNING:
Check the tire pressure carefully while inflating. Too much air in the tire could cause the tire to burst, causing serious personal injury.
VERIFY MOWER CONDITION
Inspect the entire product for damaged, missing, or loose parts such as screws, nuts, bolts, caps, etc. Tighten securely all fasteners and caps and do not operate this product until any missing or damaged parts are replaced.
CHARGE THE MOWER
See Figure 5.
Mower batteries must be fully charged before first use. To verify mower batteries are fully charged, check the battery level indicator.
To charge:

• Insert charger plug into charging port on mower, making sure it is properly connected.

• Connect charger to power supply using normal household current of 120 V, AC only, 60 Hz.

• Do not charge in an area of extreme heat or cold.

• Remove the charger from the mower once it is fully charged and ready for use.

WARNING:
To avoid accidental starting or movement of the mower that could result in death or serious personal injury, always remove the start key and set the parking brake when leaving the mower unattended.
NOTICE:
Always connect the mower to the charger when the unit is not in use. If it is not possible to leave the mower charger connected, make sure to charge the batteries fully at least once a month.
TEST THE SAFETY INTERLOCK SYSTEM
See Figure 6.
This mower features a Safety Interlock System to protect the operator by shutting off the blades if the operator leaves the seat with the blades running. Test the system to be sure it is working correctly.
To test:

• PARTS AND SERVICE: Prior to requesting service or purchasing replacement parts, please obtain your item, manufacturing, and serial numbers from the product data plate.

ITEM NO.* ____
MANUFACTURING NO.
SERIAL NO. ____

• Model/item number on product may have additional letters at the end. These letters designate manufacturing information and should be provided when calling for service.
  HOW TO OBTAIN REPLACEMENT PARTS: Replacement parts can be purchased online at www.ryobitools.com or by calling 1-800-525-2579. Replacement parts can also be obtained at one of our service centers.
  HOW TO LOCATE A SERVICE CENTER: Service centers can be located online at www.ryobitools.com or by calling 1-800-525-2579.
  HOW TO OBTAIN CUSTOMER OR TECHNICAL SUPPORT: To obtain customer or technical support please contact us at 1-800-525-2579.
  RYOBI is a registered trademark of Ryobi Limited and is used pursuant to a license granted by Ryobi Limited.

TTI OUTDOOR POWER EQUIPMENT, INC.
P.O. Box 1288, Anderson, SC 29622, USA
1-800-525-2579
www.ryobitools.com
998000965
3-11-22 (REV:01)

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>