RYOBI RY36CSX35A Cordless Chainsaw Instruction Manual
- October 30, 2023
- RYOBI
Table of Contents
- INTENDED USE
- GENERAL POWER TOOL SAFETY WARNINGS
- ADDITIONAL GENERAL SAFETY WARNINGS
- ADDITIONAL BATTERY SAFETY WARNINGS
- CHAINSAW SAFETY WARNINGS
- ADDITIONAL CHAINSAW SAFETY WARNINGS
- GETTING STARTED
- TRANSPORTATION AND STORAGE
- MAINTENANCE
- RISK REDUCTION
- KNOW YOUR PRODUCT
- SYMBOLS ON THE PRODUCT
- SYMBOLS IN THIS MANUAL
- Parts List
- Operating Instructions
- References
- Read User Manual Online (PDF format)
- Download This Manual (PDF format)
RYOBI RY36CSX35A Cordless Chainsaw
Important! It is essential that you read the instructions in this manual before assembling, maintaining and operating the product.
Subject to technical modification
Safety, performance, and dependability have been given top priority in the design of your cordless chainsaw.
INTENDED USE
The product is intended for outdoor use only. For safety reasons, the product
must be adequately controlled by using two-handed operation at all times.
The product is designed for cutting branches, trunks, logs and beams of a
diameter determined by the cutting length of the guide bar. It is designed to
cut wood only. It is only to be used in domestic application by adults who
have received adequate training on the hazards and preventative
measures/actions to be taken while using the product.
The product is not to be used by children or by persons not wearing adequate
personal protective equipment and clothing. It is also not to be used for
professional tree services. Do not use the product for any other purpose.
WARNING
When using the product, the safety rules must be followed. For your own safety and that of bystanders, you must read and fully understand these instructions before operating the product. You should attend a professionally organised course on the use and maintenance of chainsaws, preventative actions and first aid. Please keep these instructions safe for later use.
WARNING
Chainsaws are potentially dangerous tools. Accidents involving the use of chainsaws often result in loss of limbs or death. It is not just the product that is the hazard. Falling branches, toppling trees, rolling logs can all kill. Diseased or rotting timber poses additional hazards. Assess your capability of completing the task safely. If there is any doubt, leave it to a professional tree surgeon.
GENERAL POWER TOOL SAFETY WARNINGS
WARNING
Read all safety warnings, instructions, illustrations and specifications
provided with this power tool.
Failure to follow all instructions listed below may result in electric shock,
fire and/or serious injury.
Save all warnings and instructions for future reference.
The term “power tool’’ in the warnings refers to your mains-operated (corded) power tool or battery-operated (cordless) power tool.
WORK AREA SAFETY
- Keep work area clean and well lit. Cluttered or dark areas invite accidents.
- Do not operate power tools in explosive atmospheres, such as in the presence of flammable liquids, gases or dust. Power tools create sparks which may ignite the dust or fumes.
- Keep children and bystanders away while operating a power tool. Distractions can cause you to lose control.
ELEC TRICAL SAFETY
- Power tool plugs must match the outlet. Never modify the plug in any way. Do not use any adapter plugs with earthed (grounded) power tools. Unmodified plugs and matching outlets will reduce risk of electric shock.
- Avoid body contact with earthed or grounded surfaces, such as pipes, radiators, ranges and refrigerators. There is an increased risk of electric shock if your body is earthed or grounded.
- Do not expose power tools to rain or wet conditions. Water entering a power tool will increase the risk of electric shock.
- Do not abuse the cord. Never use the cord for carrying, pulling or unplugging the power tool. Keep cord away from heat, oil, sharp edges or moving parts. Damaged or entangled cords increase the risk of electric shock.
- When operating a power tool outdoors, use an extension cord suitable for outdoor use. Use of a cord suitable for outdoor use reduces the risk of electric shock.
- If operating a power tool in a damp location is unavoidable, use a residual current device (RCD) protected supply. Use of an RCD reduces the risk of electric shock.
PERSONAL SAFETY
- Stay alert, watch what you are doing and use common sense when operating a power tool. Do not use a power tool while you are tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating power tools may result in serious personal injury.
- Use personal protective equipment. Always wear eye protection. Protective equipment such as a dust mask, non-skid safety shoes, hard hat or hearing protection used for appropriate conditions will reduce personal injuries.
- Prevent unintentional starting. Ensure the switch is in the off-position before connecting to power source and/or battery pack, picking up or carrying the tool. Carrying power tools with your finger on the switch or energising power tools that have the switch on invites accidents.
- Remove any adjusting key or wrench before turning the power tool on. A wrench or a key left attached to a rotating part of the power tool may result in personal injury.
- Do not overreach. Keep proper footing and balance at all times. This enables better control of the power tool in unexpected situations.
- Dress properly. Do not wear loose clothing or jewellery. Keep your hair and clothing away from moving parts. Loose clothes, jewellery or long hair can be caught in moving parts.
- If devices are provided for the connection of dust extraction and collection facilities, ensure these are connected and properly used. Use of dust collection can reduce dust-related hazards.
- Do not let familiarity gained from frequent use of tools allow you to become complacent and ignore tool safety principles. A careless action can cause severe injury within a fraction of a second.
POWER TOOL USE AND CARE
- Do not force the power tool. Use the correct power tool for your application. The correct power tool will do the job better and safer at the rate for which it was designed.
- Do not use the power tool if the switch does not turn it on and off. Any power tool that cannot be controlled with the switch is dangerous and must be repaired.
- Disconnect the plug from the power source and/ or remove the battery pack, if detachable, from the power tool before making any adjustments, changing accessories, or storing power tools. Such preventive safety measures reduce the risk of starting the power tool accidentally.
- Store idle power tools out of the reach of children and do not allow persons unfamiliar with the power tool or these instructions to operate the power tool. Power tools are dangerous in the hands of untrained users.
- Maintain power tools and accessories. Check for misalignment or binding of moving parts, breakage of parts and any other condition that may affect the power tool’s operation. lf damaged, have the power tool repaired before use. Many accidents are caused by poorly maintained power tools.
- Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp cutting edges are less likely to bind and are easier to control.
- Use the power tool, accessories and tool bits etc. in accordance with these instructions, taking into account the working conditions and the work to be performed. Use of the power tool for operations different from those intended could result in a hazardous situation.
- Keep handles and grasping surfaces dry, clean and free from oil and grease. Slippery handles and grasping surfaces do not allow for safe handling and control of the tool in unexpected situations.
BATTERY TOOL USE AND CARE
- Recharge only with the charger specified by the manufacturer. A charger that is suitable for one type of battery pack may create a risk of fire when used with another battery pack.
- Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury and fire.
- When battery pack is not in use, keep it away from other metal objects, like paper clips, coins, keys, nails, screws or other small metal objects, that can make a connection from one terminal to another. Shorting the battery terminals together may cause burns or a fire.
- Under abusive conditions, liquid may be ejected from the battery; avoid contact. If contact accidentally occurs, flush with water. If liquid contacts eyes, additionally seek medical help. Liquid ejected from the battery may cause irritation or burns.
- Do not use a battery pack or tool that is damaged or modified. Damaged or modified batteries may exhibit unpredictable behaviour resulting in fire, explosion or risk of injury.
- Do not expose a battery pack or tool to fire or excessive temperature. Exposure to fire or temperature above 130°C may cause explosion.
- Follow all charging instructions and do not charge the battery pack or tool outside the temperature range specified in the instructions. Charging improperly or at temperatures outside the specified range may damage the battery and increase the risk of fire
SERVICE
- Have your power tool serviced by a qualified repair person using only identical replacement parts. This will ensure that the safety of the power tool is maintained.
- Never service damaged battery packs. Service of battery packs should only be performed by the manufacturer or authorised service providers.
ADDITIONAL GENERAL SAFETY WARNINGS
- Some regions have regulations that restrict the use of the product. Check with your local authority for advice.
- Never allow children or people who are unfamiliar with the instructions to use the product. Local regulations may restrict the age of the operator.
- Ensure before each use that all controls and safety devices function correctly. Do not use the product if the “off” switch does not stop the motor.
- Wear full eye and hearing protection, strong sturdy boots and gloves, and head protection while operating the product. Use a face mask if operation is dusty.
- Use of hearing protection reduces the ability to hear warnings (shouts or alarms). The operator must pay extra attention to what is going on in the work area.
- Keep firm footing and balance. Do not overreach. Overreaching can result in loss of balance and can increase the risk of kickback.
- Do not wear loose-fitting clothing, short trousers, or jewellery of any kind.
- Secure long hair so it is above shoulder level to prevent entanglement in moving parts.
- Beware of thrown, flying, or falling objects. Keep all bystanders, children, and animals at least 15 m away from the work area.
- Do not operate the product in poor lighting. The operator requires a clear view of the work area to identify potential hazards.
- Operating similar tools nearby increases both the risk of hearing injury and the potential for other persons to enter your work area.
- Keep all parts of your body away from any moving part.
- Inspect the product before each use. Check for correct operation of all controls, including the chain brake. Check for loose fasteners, and make sure that all guards and handles are properly and securely attached. Replace any damaged parts before use.
- Do not modify the product in any way or use parts and accessories which are not recommended by the manufacturer.
WARNING
If the product is dropped, suffers heavy impact or begins to vibrate abnormally, immediately stop the product and inspect for damage or identify the cause of the vibration. Any damage should be properly repaired or replaced by an authorised service centre.
ADDITIONAL BATTERY SAFETY WARNINGS
WARNING
To reduce the risk of fire, personal injury, and product damage due to short circuit, never immerse your tool, battery pack, or charger in fluid or allow a fluid to flow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach-containing products, etc., can cause a short circuit.
OVER-TEMPERATURE PROTECTION
The battery pack has an over-temperature protection, which is designed to protect the battery cells from damage in the event of high temperatures. This feature may cause the battery to stop powering the product until the battery cells cool down. Feel the battery pack; if it is warm to touch, allow it to cool down before resuming operation. If the product still does not work, connect the battery pack to the charger, which can also indicate over- temperature protection. When the battery cells cool down, the charger begins to charge the battery.
NOTE: High ambient temperatures above 30° C and high power tools, such as chainsaw, can cause the battery cells to heat up faster. Monitor the battery pack regularly, and if it is warm to touch, change the battery or allow the battery to cool down.
NOTE : The battery pack LED indicator stops working if the battery protection feature has caused the battery pack to stop powering the product.
CHAINSAW SAFETY WARNINGS
- Keep all parts of the body away from the saw chain when the chainsaw is operating. Before you start the chainsaw, make sure the saw chain is not contacting anything. A moment of inattention while operating chainsaws may cause entanglement of your clothing or body with the saw chain.
- Always hold the chainsaw with your right hand on the rear handle and your left hand on the front handle. Holding the chainsaw with a reversed hand configuration increases the risk of personal injury and should never be done.
- Hold the chainsaw by insulated gripping surfaces only, because the saw chain may contact hidden wiring or its own cord. Saw chains contacting a “live” wire may make exposed metal parts of the chainsaw “live” and could give the operator an electric shock.
- Wear eye protection. Further protective equipment for hearing, head, hands, legs and feet is recommended. Adequate protective equipment will reduce personal injury by flying debris or accidental contact with the saw chain.
- Do not operate a chainsaw in a tree, on a ladder, from a rooftop, or any unstable support. Operation of a chainsaw in this manner could result in serious personal injury.
- Always keep proper footing and operate the chainsaw only when standing on fixed, secure and level surface. Slippery or unstable surfaces may cause a loss of balance or control of the chainsaw.
- When cutting a limb that is under tension, be alert for spring back. When the tension in the wood fibres is released, the spring loaded limb may strike the operator and/or throw the chainsaw out of control.
- Use extreme caution when cutting brush and saplings. The slender material may catch the saw chain and be whipped toward you or pull you off balance.
- Carry the chainsaw by the front handle with the chainsaw switched off and away from your body. When transporting or storing the chainsaw, always fit the guide bar cover. Proper handling of the chainsaw will reduce the likelihood of accidental contact with the moving saw chain.
- Follow instructions for lubricating, chain tensioning and changing the bar and chain. Improperly tensioned or lubricated chain may either break or increase the chance for kickback.
- Cut wood only. Do not use chainsaw for purposes not intended. For example: do not use chainsaw for cutting metal, plastic, masonry or non-wood building materials. Use of the chainsaw for operations different than intended could result in a hazardous situation.
- Do not attempt to fell a tree until you have an understanding of the risks and how to avoid them. Serious injury could occur to the operator or bystanders while felling a tree.
Causes and operator prevention of kickback
Kickback may occur when the nose or tip of the guide bar touches an object, or
when the wood closes in and pinches the saw chain in the cut.
Tip contact in some cases may cause a sudden reverse reaction, kicking the
guide bar up and back towards the operator.
Pinching the saw chain along the top of the guide bar may push the guide bar
rapidly back towards the operator. Either of these reactions may cause you to
lose control of the saw which could result in serious personal injury. Do not
rely exclusively upon the safety devices built into your saw. As a chainsaw
user, you should take several steps to keep your cutting jobs free from
accident or injury. Kickback is the result of tool misuse and/or incorrect
operating procedures or conditions and can be avoided by taking proper
precautions as given below:
- Maintain a firm grip, with thumbs and fingers encircling the chainsaw handles, with both hands on the saw and position your body and arm to allow you to resist kickback forces. Kickback forces can be controlled by the operator, if proper precautions are taken. Do not let go of the chainsaw.
- Do not overreach and do not cut above shoulder height. This helps prevent unintended tip contact and enables better control of the chainsaw in unexpected situations.
- Use only replacement bars and chains that are specified by the manufacturer. Incorrect replacement bars and chains may cause chain breakage and/or kickback.
- Follow the manufacturer’s sharpening and maintenance instructions for the saw chain. Decreasing the depth gauge height can lead to increased kickback.
ADDITIONAL CHAINSAW SAFETY WARNINGS
- It is recommended to cut logs on a saw-horse or cradle when operating the product for the first time.
- Ensure that all guards, handles, and spiked bumper are properly fitted and are in good condition.
- Persons using this chainsaw should be in good health. The chainsaw is a heavy unit so the operator requires to be physically fit. The operator should be alert, have good vision, mobility, balance and manual dexterity. If there is any doubt, do not operate the chainsaw.
- Do not start using the product until you have a clear work area, secure footing, and a planned retreat path away from the falling tree.
- Beware of the emission of lubricant mist and saw dust. Wear a mask or respirator if required.
- Do not cut vines and/or small undergrowth (less than 75 mm in diameter).
- Always hold the chainsaw with both hands when operating the saw. Use a firm grip with thumbs and fingers encircling the chainsaw handles. Right hand must be on the rear handle and left hand on the front handle.
- Before starting the product, make sure that the saw chain is not contacting any object.
- Do not modify your tool in any way or use it to power any attachments or devices that are not recommended by the manufacturer for your saw.
- There should be a first-aid kit containing large wound dressings and a means to summon attention (e.g., whistle) close to the operator. A larger more comprehensive kit should be reasonably nearby.
- Wear a helmet at all times when operating the product. A helmet, equipped with mesh visor, can help reduce the risk of injury to the face and the head if kickback occurs.
- An incorrectly tensioned chain can jump off the guide bar and could result in serious injury or fatality. The length of chain depends on the temperature of the chain and chain wear. Check the tension frequently.
- You should get used to your new chainsaw by making simple cuts on securely supported wood. Do this whenever you have not operated the saw for some time.
- To reduce the risk of injury associated with contacting moving parts, always stop the motor, apply chain brake, remove the battery pack, and make sure that all moving parts have come to a stop before:
- cleaning or clearing a blockage
- leaving the product unattended
- installing or removing attachments
- checking, maintenance or working on the product
- The size of the work area depends on the job being performed as well as the size of the tree or work piece involved. For example, felling a tree requires a larger work area than making other cuts, i.e., bucking cuts, etc. The operator needs to be aware and in control of everything happening in this work area.
- Do not cut with your body in line with the guide bar and chain. If you do experience kickback this will help prevent the chain from coming into contact with your head or body.
- Do not use a back and forward sawing motion, let the chain do the work, keep the chain sharp and don’t try to push the chain through the cut.
- Do not put pressure on the saw at the end of the cut. Be ready to take on the weight of the saw as it cuts free from the wood. Failure to do so could result in possible serious personal injury.
- Do not stop the saw in the middle of a cutting operation. Keep the saw running until it is removed from the cut.
Personal protective equipment
Good quality personal protective equipment as used by professionals will help to reduce the risk of injury to the operator. The following items should be used when operating your chainsaw:
Safety helmet
- should comply with EN 397 and be CE marked
Hearing protection
- should comply with EN 352-1 and be CE marked
Eye and face protection
- should be CE marked and comply with EN 166 (for safety glasses) or EN 1731 (for mesh visors)
Gloves
- should comply with EN381-7 and be CE marked
Leg protection (chaps)
- should comply with EN381-5, be CE marked and provide all-round protection.
Chainsaw safety boots
- should comply with EN ISO 20345:2004 and be marked with a shield depicting a chainsaw to show compliance with EN 381-3. (Occasional users may use steel toecap safety boots with protective gaiters which conform to EN 381-9 if the ground is even and there is little risk
of tripping or catching on undergrowth)
Chainsaw jackets for upper body protection
- should comply with EN 381-11 and be CE marked
GETTING STARTED
- Wear full eye protection, ear protection, non-slip heavy-duty gloves, substantial footwear, and protective clothing at all times while operating the product. Do not operate the product when barefoot or wearing open sandals.
- Remove the parts from the packaging. Inspect the product carefully for damage. If any parts are damaged or missing, contact an authorised service centre.
- Add chain lubricating oil. Clear the surface around the oil cap to prevent contamination. Remove the cap from the oil tank. Pour the oil into the oil tank and monitor the oil level gauge. Ensure that no dirt enters the oil tank while filling. Close the oil tank, and tighten the cap. Wipe away any spillage.
NOTE: Ensure that the lubricant flow screw is set to open for chain and bar oil to be released.
– Turn the screw counterclockwise to open and increase the oil flow to the chain and bar.
– Turn the screw clockwise to decrease the oil flow to the chain and bar.
A properly functioning chain and bar lubricating system will normally discharge oil from the chain during use. To check the functionality of the chain and bar lubricating system, point the tip of the chain at a light coloured surface, such as a newspaper. A distinct line of oil splatter should be observed after a short time.
WARNING
Never work without chain lubricant. If the saw chain is running without
lubricant, the guide bar and the saw chain can be damaged. It is essential to
frequently check the oil level in the oil level gauge and before starting to
use the chainsaw.
4. Remove the guide bar cover.
5. Adjust the chain tension. Turn the chain tensioner knob counterclockwise to unlock the chain tensioner adjustment ring. Check the chain tension frequently while adjusting the tension.
– To increase the chain tension, turn the chain tensioner adjustment ring
clockwise.
– To reduce the chain tension, turn the chain tensioner adjustment ring
counterclockwise.
NOTE : The chain tension is correct when the gap between the cutter in
the chain and the bar is between 3-4 mm. Pull the chain in the middle of the
lower side of the bar downwards (away from the bar), and measure the distance
between the bar and the chain cutters.
NOTE: The temperature of the chain increases during normal operation
causing the chain to stretch. Check the chain tension frequently and adjust as
required.
A chain tensioned while warm may be too tight upon cooling. Make sure that the
chain tension is correctly adjusted as specified in these instructions.
- Tighten the chain tensioner knob by turning it clockwise.
- Align the raised ribs on the battery pack with the grooves in the product’s battery port. Make sure that the latch of the battery pack snaps in place and that the battery pack is fully seated and securely attached before beginning operation.
WARNING
Always hold the product with your right hand on the rear handle and your left hand on the front handle.
WARNING
Grip both handles with the thumbs and fingers encircling the handles. Ensure
that your left hand is holding the front handle so that your thumb is
underneath.
8. Start the product. Set the chain brake into the run position by grasping the top of the chain brake lever/hand guard and pulling towards the front handle until you hear a click. Pull the trigger release. Press the throttle trigger.
NOTE: To stop the product, engage the chain brake by rotating your left
hand around the front handle. Allow the back of your hand to push the chain
brake lever/hand guard toward the bar while the chain is rotating rapidly.
Push the trigger release and release the throttle trigger.
INSTRUCTIONS CONCERNING THE PROPER TECHNIQUES FOR BASIC FELLING, LIMBING, AND CROSS-CUTTING
Understanding the forces within the wood
When you understand the directional pressures and stresses inside the wood you
can reduce the “pinches” or at least expect them during your cutting. Tension
in the wood means the fibers are being pulled apart and if you cut in this
area, the “kerf” or cut will tend to open as the saw goes through. If a log is
being supported on a saw horse and the end is hanging unsupported over the end
then tension is created on the upper surface due to the weight of the
overhanging log stretching the fibers. Likewise, the underside of the log will
be in compression and the fibers are being pushed together. If a cut is made
in this area, the kerf will have the tendency to close up during the cut. This
would pinch the blade.
Push and pull
The reaction force is always opposite to the direction the chain is moving.
Thus, the operator must be ready to control the tendency for the product to
pull away (forward motion) when cutting on the bottom edge of the bar and the
push backwards (towards the operator) when cutting along the top edge.
Saw jammed in the cut
Stop the chainsaw and make it safe. Do not try to force the chain and bar out of the cut as this is likely to break the chain, which may swing back and strike the operator. This situation normally occurs because the wood is incorrectly supported and forcing the cut to close under compression thereby pinching the blade. If adjusting the support does not release the bar and chain, use wooden wedges or a lever to open the cut and release the saw. Never try to start the chainsaw when the guide bar is already in a cut or kerf.
Skating/Bouncing
When the chainsaw fails to dig in during a cut, the guide bar can dangerously begin hopping or skidding along the surface of the log or branch, possibly resulting in the loss of control of the chainsaw. To prevent or reduce skating or bouncing, always use the saw with both hands. Make sure that the saw chain establishes a groove for cutting.
Never cut small, flexible branches or brushes with your chainsaw. Their size and flexibility can easily cause the saw to bounce towards you or bind up with enough force to cause a kickback. The best tool for that kind of work is a hand saw, pruning shears, an axe or other hand tools.
Felling a tree
When bucking and felling operations are being performed by two or more persons
at the same time, the felling operations should be separated from the bucking
operation by a distance of at least twice the height of the tree being felled.
Trees should not be felled in a manner that would endanger any person, strike
any utility line, or cause any property damage. If the tree does make contact
with any utility line, the company should be notified immediately.
The chainsaw operator should keep on the uphill side of the terrain as the
tree is likely to roll or slide downhill after it is felled.
An escape path should be planned and cleared as necessary before cuts are
started. The escape path should extend back and diagonally to the rear of the
expected line of fall.
-
Notching undercut
Make the notch 1/3 the diameter of the tree, perpendicular to the direction of falls. Make the lower horizontal notching cut first. This will help to avoid pinching either the saw chain or the guide bar when the second notch is being made.
-
Felling back cut
Make the felling back cut at least 50 mm (2 inches) higher than the horizontal notching cut. Keep the felling back cut parallel to the horizontal notching cut. Make the felling back cut so enough wood is left to act as a hinge. The hinge wood keeps the tree from twisting and falling in the wrong direction. Do not cut through the hinge.
As the felling gets close to the hinge, the tree should begin to fall. If there is any chance that the tree may not fall in desired direction or it may rock back and bind the saw chain, stop cutting before the felling back cut is complete, and use wedges of wood, plastic or aluminium to open the cut and drop the tree along the desired line of fall.
When the tree begins to fall, remove the chainsaw from the cut, stop the motor, put the chainsaw down, then use the retreat path planned. Be alert for overhead limbs falling, and watch your footing.
Removing buttress roots
A buttress root is a large root extending from the trunk of the tree above the
ground. Remove large buttress roots prior to felling. Make the horizontal cut
into the buttress fi rst, followed by the vertical cut. Remove the resulting
loose section from the work area. Follow the correct tree felling procedure
after you have removed the large buttress roots.
Bucking a log
Bucking is cutting a log into lengths. It is important to make sure that your footing is firm and your weight is evenly distributed on both feet. When possible, the log should be raised and supported by the use of limbs, logs, or chocks. Follow the directions for easy cutting. When the log is supported along its entire length, it is cut from the top (over buck).
When the log is supported on one end, cut 1/3 the diameter from the underside
(under buck). Make the finished cut by over bucking to meet the first cut.
When the log is supported on both ends, cut 1/3 the diameter from the top
(over buck). Make the finished cut by under bucking the lower 2/3 to meet the
first cut
When bucking on a
slope, always stand on the uphill side of the log. When “cutting through”, to
maintain complete control release the cutting pressure near the end of the cut
without relaxing your grip on the chainsaw handles. Do not let the chain
contact the ground. After completing the cut, wait for the saw chain to stop
before you move the chainsaw. Always stop the motor before moving from tree to
tree.
Limbing a tree
Limbing is the process of removing the branches from a fallen tree. When
limbing, leave larger lower limbs to support the log off the ground. Remove
the small limbs in one cut. Branches under tension should be cut from the
bottom up to avoid binding the chainsaw.
Spring poles
A spring pole is any log, branch, rooted stump, or sapling that is bent under tension by other wood so that it springs back if the wood holding it is cut or removed.
On a fallen tree, a rooted stump has a high potential of springing back to the
upright position during the bucking cut to separate the log from the stump.
Watch out for springpoles—they are dangerous. Do not attempt to cut bent
branches or stumps that are under tension unless you are professionally
trained and competent to do so.
WARNING
TRANSPORTATION AND STORAGE
-
Stop the product, remove the battery pack, and allow the product to cool down before storing or transporting.
-
Clean all foreign material from the product. Store it in a cool, dry, and well-ventilated place that is inaccessible to children. Keep the product away from corrosive agents such as garden chemicals and de-icing salts.
Do not store the product outdoors. -
Fit guide bar cover before storing the product, or during transportation.
-
For transportation, secure the product against movement or falling to prevent injury to persons or damage to the product.
TRANSPORTING LITHIUM BATTERIES
Transport the battery in accordance with local and national provisions and regulations.
Follow all special requirements on packaging and labelling when transporting batteries by a third party. Ensure that no batteries can come in contact with other batteries or conductive materials while in transport by protecting exposed connectors with insulating, non-conductive caps or tape. Do not transport batteries that are cracked or leaking. Check with the forwarding company for further advice.
MAINTENANCE
WARNING
Use only original manufacturer’s replacement parts, accessories and attachments. Failure to do so can cause possible injury, can contribute to poor performance, and may void your warranty.
WARNING
Servicing requires extreme care and knowledge and should be performed only by a qualified service technician. Have the product serviced by an authorised service centre only. When servicing, use only original replacement parts.
WARNING
Remove the battery before adjustment, maintenance or cleaning. Failure to do so could result in serious personal injury.
- You may make adjustments or repairs described in this manual. For other repairs, contact the authorized service agent.
- Consequences of improper maintenance, removal, or modification of safety features, such as the chain brake, ignition switch, hand guard (front and back), spiked bumper, chain catcher, guide bar, and low kickback saw chain may cause the safety features to not function correctly, thus increasing the potential for serious injury. Keep your chainsaw professionally maintained and safe.
- Sharpening the chain safely is a skilled task. Therefore the manufacturer strongly recommends that a worn or dull chain is replaced with a new one, available from your authorised RYOBI service centre. The part number is available in the product specification table in this manual.
- Follow instructions for lubricating and chain tension checking and adjustment.
- After each use, clean the product with a soft, dry cloth.
- Check all nuts, bolts, and screws at frequent intervals for security to ensure the product is in safe working condition. Any part that is damaged should be properly repaired or replaced by an authorized service centre
MAINTENANCE SCHEDULE
Daily check
Bar lubrication| Before each use
Chain tension| Before each use and frequently
Chain sharpness| Before each use, visual check
For damaged parts| Before each use
For loose fasteners| Before each use
Chain brake function| Before each use
Inspect and clean
Bar| Before each use
Complete saw| After each use
Chain brake| Every 5 hours*
Hours of operation
RESIDUAL RISKS
Even when the product is used as prescribed, it is still impossible to completely eliminate certain residual risk factors. The following hazards may arise in use and the operator should pay special attention to avoid the following:
- injury caused by vibration
- Always use the right tool for the job, use designated handles and restrict working time and exposure.
- damage to hearing due to exposure to noise
- Wear hearing protection and limit exposure.
- injury caused by contact with exposed saw teeth of the chain (cutting hazards)
- injury caused by unforeseen, abrupt movement or kickback of the guide bar (cutting hazards)
- injury caused by parts ejected from the saw chain (cutting/injection hazards)
- injury caused by thrown-out pieces of the workpiece (wood chips, splinters)
- injury caused by dust and particles
- injury to the skin caused by contact with lubricants
RISK REDUCTION
It has been reported that vibrations from hand-held tools may contribute to a condition called Raynaud’s Syndrome in certain individuals. Symptoms may include tingling, numbness, and blanching of the fingers, usually apparent upon exposure to cold. Hereditary factors, exposure to cold and dampness, diet, smoking and work practices are all thought to contribute to the development of these symptoms. There are measures that can be taken by the operator to possibly reduce the effects of vibration:
- Keep your body warm in cold weather. When operating the product. Wear gloves to keep the hands and wrists warm. It is reported that cold weather is a major factor contributing to Raynaud’s Syndrome.
- After each period of operation, exercise to increase blood circulation.
- Take frequent work breaks. Limit the amount of exposure per day.
- Protective gloves available from professional chainsaw retailers are designed specifically for chainsaw use , which give protection, good grip, and reduce the effect of handle vibration.
If you experience any of the symptoms of this condition, immediately discontinue use and see your physician.
WARNING
Injuries may be caused, or aggravated, by prolonged use of a tool. When using any tool for prolonged periods, ensure you take regular breaks.
KNOW YOUR PRODUCT
- Saw chain
- Guide bar
- Front hand guard/Chain brake
- Front handle
- Rear handle
- Chain lubricant cap
- Guide bar cover
- Chain tensioner knob
- Chain tensioner adjustment ring
- Sprocket cover
- Switch trigger
- Trigger release
- Spiked bumper
SAFETY DEVICES
Low kick-back saw chain
A low-kick-back saw chain helps to reduce the possibility of a kickback event.
The rakers (depth gauges) ahead of each cutter can minimize the force of a kick-back reaction by preventing the cutters from digging in too deeply. Only use replacement guide bar and chain combinations recommended by the manufacturer.
As saw chains are sharpened, they lose some of the low kickback qualities and extra caution is required. For your safety, replace saw chains when cutting performance decreases.
Spiked bumper
The integral bumper spike may be used as a pivot when making a cut. It helps to keep the body of the chainsaw steady while cutting. When cutting, push the product forward until the spikes dig into the edge of the wood, then by moving the rear handle up or down in the direction of the cutting line it can help ease the physical strain of cutting
Guide bars
Generally, guide bars with small radius tips have somewhat lower potential for kick-back. Use a guide bar and matching chain that is just long enough for the job. Longer bars increase the risk of loss of control during sawing. Regularly check the chain tension. When cutting smaller branches (less than the full length of the guide bar), the chain is more likely to be thrown off if the tension is not correct.
Chain brake
Chain brakes are designed to quickly stop the chain rotating. When the chain brake lever/hand guard is pushed towards the bar, the chain should stop immediately. A chain brake does not prevent kick-back. It only lowers the risk of injury should the chain bar contact the operator’s body during a kick-back event. The chain brake should be tested before each use for correct operation in both the run and brake positions.
WARNING
If the chain brake does not stop the chain immediately, or if the chain brake will not stay in the run position without assistance, take the product to an authorised service centre for repair prior to use.
Chain catcher
A chain catcher prevents the saw chain from being thrown back towards to the operator if the saw chain comes loose or breaks.
SYMBOLS ON THE PRODUCT
| Safety alert
---|---
| Read and understand all instructions before operating the product. Follow
all warnings and safety instructions.
| Wear eye, ear, and head
protection.
| Wear non-slip safety footwear
when using the product.
| Wear non-slip, heavy-duty gloves.
| Beware of chain saw kickback and avoid contact with bar tip.
| Do not expose the product to rain or damp conditions.
| Hold and operate the saw properly with both hands.
| Do not operate the saw using only one hand.
| Set the chain brake to the RUN position.
| Set the chain brake to the BRAKE position.
| Conforms to all regulatory standards in the country in the EU where the
product is purchased.
| EurAsian Conformity Mark
| Ukrainian mark of conformity
| Waste electrical products should not be disposed of with household waste.
Please recycle where facilities exist. Check with your local authority or
retailer for recycling advice.
| The guaranteed sound power level is 101 dB.
| Bar and chain lubricant
| Minimum lubricant level
| Lock
| Unlock
| Rotate to adjust chain tension
+ = Tighten the chain
– = Loosen the chain
| Moving direction of the chain. (Marked under the sprocket cover
V0 : 21m/s| No-load chain speed is 21 m/s
L max: 356mm| Maximum guide bar length is 356 mm
SYMBOLS IN THIS MANUAL
| Parts or accessories sold separately
---|---
| Note
| Warning
| Wear eye and face protection.
| Wear upper body protection.
| Wear leg protection.
| Stop the product.
The following signal words and meanings are intended to explain the levels of risk associated with this product.
DANGER
Indicates an imminently hazardous situation, which, if not avoided, will
result in death or serious injury.
WARNING
Indicates a potentially hazardous situation, which, if not avoided, could
result in death or serious injury.
CAUTION
Indicates a potentially hazardous situation, which, if not avoided, may result
in minor or moderate injury.
CAUTION
Without safety alert symbol
Indicates a situation that may result in property damage.
Parts List
Operating Instructions
Product specifications
Cordless Chainsaw
Model
Rated voltage
No-load speed
Guide bar length
Usable cutting length
Chain stop
Chain oil tank capacity
Weight (without battery pack, with guide bar, chain and empty tank)
Vibration level (in accordance with EN 60745-1 & EN 60745-2-13)
Front handle
Rear handle
Uncertainty of measurement
Noise emission level (in accordance with EN 60745-1 & EN 60745-2-13)
A-weighted sound pressure level at operator’s position
Uncertainty of measurement
A-weighted sound power level
Uncertainty of measurement
Chain length
Chain pitch
Chain guage
Drive links quantity
Battery and charger
Model
Battery pack
Weight
Charger
Compatible battery packs
Compatible Charger
Replacement Part (Bar and Chain)
Manufacturer
Chain
Bar
Chain must be fitted with bar from the same manufacturer according to above
combinations.
Vibration level
The declared vibration value has been measured with a standard test method and may be used to compare one tool with another.
The declared vibration value may be used in a preliminary assessment of exposure.
The vibration emission during actual use of power tool can differ from the declared total value depending on the ways in which the tool is used.
Identify safety measures to protect yourself based on an estimation of exposure in the actual conditions of use, taking account of all parts of the operating cycle such as the times when the tool is switched off and when it is running idle in addition to the trigger time
RYOBI® WARRANTY APPLICATION CONDITIONS
In addition to any statutory rights resulting from the purchase, this product is covered by a warranty as stated below.
-
The warranty period is 24 months for consumers and commences on the date when the product was purchased. This date has to be documented by an invoice or other proof of purchase. The product is designed and dedicated to consumer and private use only. So there is no warranty provided in case of professional or commercial use. This warranty applies only on new products.
-
There is a possibility to extend for a part of the range of power tools (AC/DC) the warranty period over the period described above using the registration on the www.ryobitools.eu website. The eligibility of products for extended warranty is clearly displayed in stores and / or on packaging and is contained within the product documentation. The end user is required to register his/her newly-acquired products online within 30 days from the date of purchase. The end user may register for the extended warranty in his/her country of residence if listed on the online registration form where this option is valid. Furthermore, end users must give their consent to the storage of their personal data that is required to be entered online. They must also accept the terms and conditions. The registration confirmation receipt, which is sent out by e-mail, and the original invoice showing the date of purchase will serve as proof of the extended warranty.
-
The warranty covers all defects of the product during the warranty period due to faults in workmanship or material at the purchase date. The warranty is limited to repair and/or replacement and does not include any other obligations including but not limited to incidental or consequential damages.
The warranty is not valid if the product has been misused, used contrary to the instruction manual, or has been incorrectly connected to a power supply.
This warranty does not apply to:
– any damage to the product that is the result of improper or lack of maintenance
– any product that has been altered or modified
– any product where original identification (trade mark, serial number) markings have been defaced, altered or removed
– any damage caused by non-observance of the instruction manual
– any product not displaying the CE approval mark on the rating plate
– any product that has been attempted to be repaired by a non-authorised warranty service centre or without prior authorisation by Techtronic Industries
– any product connected to improper power supply (amps, voltage, frequency)
– any product used with inappropriate fuel mixture (fuel, oil, ratio of oil/ fuel mixture)
– any damage caused by external influences (water, chemical, physical, shocks) or foreign substances
– normal wear and tear spare parts
– inappropriate use, overloading of the tool
– use of non-approved accessories or parts
– Accessories provided with the tool or purchased separately including but not limited to blades, saw chains, cutting lines, etc.
– Any periodic adjustments to or maintenance cleaning of carburettors
– Components (parts and accessories) subject to natural wear and tear, including but not limited to bump knobs, drive belts, clutch, blades of hedge trimmers or lawn mowers, harness, cable throttle, carbon brushes, power cord, tines, felt washers, hitch pins, blower fans, blower and vacuum tubes, vacuum bag and straps, guide bars, saw chains, hoses, connector fittings, spray nozzles, wheels, spray wands, inner reels, outer spools, cutting lines, spark plugs, air filters, gas filters, mulching blades, etc. -
For servicing, the product must be sent or presented to a RYOBI authorised service station listed for each country in the following list of service station addresses. In some countries your local RYOBI dealer undertakes to send the product to the RYOBI service organisation. When sending a product to a RYOBI service station, the product should be safely packed without any dangerous contents such as petrol, marked with sender’s address and accompanied by a short description of the fault.
-
A repair / replacement under this warranty is free of charge. It does not constitute an extension or a new start of the warranty period. Exchanged parts or products become our property. In some countries delivery charges or postage will have to be paid by the sender. Your statutory rights arising from the purchase of the product remain unaffected.
-
This warranty is valid in the European Community, Switzerland, Iceland, Norway, Liechtenstein, Turkey and Russia. Outside these areas, please contact your authorised RYOBI dealer to determine if another warranty applies.
AUTHORISED SERVICE CENTRE
To find an authorised service centre near you, visit http://uk.ryobitools.eu/header/service-and-support/service-agents.
DECLARATION OF CONFORMITY
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
Herewith we declare that the product
Cordless Chainsaw
Brand: RYOBI
Model number: RY36CSX35A
Serial number range: 47508201000001 – 47508201999999
is in conformity with the following European Directives and harmonised
standards 2006/42/EC, 2014/30/EU, 2000/14/EC, 2005/88/EC, 2011/65/EU,
EN 60745-1:2009+A11:2010, EN 60745-2-13:2009+A1:2010,
EN 55014-1:2017, EN 55014-2:2015, EN IEC 63000:2018
Measured sound power level: 99.2 dB(A)
Guaranteed sound power level: 101 dB(A)
Conformity assessment method to Annex V Directive 2000/14/EC amended by
2005/88/EC.
Notified body, 0197 TÜV Rheinland LGA Products GmbH; Tillystraße 2 D – 90431
Nürnberg, Germany has carried out EC type approval, and the certificate No.
is.
BM 50443754 0001.
Todd Chipner
Sr. Director, CPT Quality and Asia Regulatory & Safety
Winnenden, Aug. 29, 2019
Authorised to compile the technical file:
Alexander Krug, Managing Director
Techtronic Industries GmbH
Max-Eyth-Straße 10, 71364 Winnenden, Germany
RYOBI is a trademark of Ryobi Limited, and is used under license.
TRILINK is a registered trademark of Trilink Saw Chain, LLC.
© 2019 Techtronic Cordless GP. All rights reserved.
References
- Servis
- Ryobi Tools
- Servicio técnico de Ryobi España
- Ryobi Tools
- SAV Ryobi France: Pièces détachées et réparations Ryobi : le service client Ryobi
- Ryobi Tools HU
- Centri di assistenza
- Ryobi Tools - Aanbiedingen Ryobi Elektrisch & Tuingereedschap
- Ryobi Norge | Elverktøy, ONE+, Hagemaskiner, 36V
- Kontakt
- Serviços técnicos
- reserved.FR
- СервиÑные центры
- Ryobi Tools
- Servicecenter
- Ryobi Tools UK | Power tools, ONE+, Outdoor, 36V
- Ryobi Tools
- Ryobi Tools UK
- Ryobi Tools
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>