Purell ES6 Soap and Sanitizer Touch Free Dispenser Instruction Manual

PURELL® ES6 Soap & Sanitizer Touch Free Dispenser Installation and Use Instructions
Please read all instructions carefully before installing and using the dispenser. Do not install in locations where dispensers may be exposed to wet environments such as showers or areas where walls are washed down.

Dispenser Installation

if installing with wall fasteners

Open the dispenser by pressing the release buttons on side of the dispenser and sliding the front cover down.| Check label inside dispenser before installing.
ES6 SOAP = soap dispenser
ES6 SAN = hand sanitizer dispenser

Install dispenser with at least 7″ free space above countertop to allow routine service.| Using the dispenser as a template, pierce the tape on the backplate to mark and drill four holes using a 1/4″ drill bit. Use the supplied wall anchor and #10 x 1″ screws to secure the dispenser in place, being careful not to overtighten. It is recommended to use 4 screws. If only two are possible, the top two holes should be used. Recommended holes are shown.

If installing with tape

Clean installation surface with an alcohol pad. Allow the surface to dry for 60 seconds then peel the paper off the installation tape and press firmly on the backplate for 10 seconds. For maximum adhesion, wait 24 hours before loading refill or using the dispenser.| Attach the backplate by pressing on the top two corners and the bottom middle section. Audible clicks will confirm proper installation.

Install the SHIELD”‘ Floor and Wall Protector into the bottom of the dispenser by aligning plastic tabs on the SHIELD with slots on the dispenser and sliding up until the tabs snap into place. (SHIELD is included with Sanitizer Systems and can be ordered for Soap systems). 7745-WHT-18 White SHIELD Floor and Wall Protector 7745-GPH-18 Graphite SHIELD Floor and Wall Protector| Remove battery tab to activate the dispenser.

Match label on refill with label on dispenser.| Remove refill cap and push the new refill into dispenser until it clicks in place.

Close dispenser cover. The green status light will blink after closing, indicating the dispenser is ready to use.| Place palms approximately 2″ below the dispenser, product will dispense within 1 second of sensor activation.

Refill Replenishment

Open the dispenser by pressing the release buttons on side of the dispenser and sliding the front cover down.| Push the green release button and remove empty refill.

Match the label on the refill with the label on the dispenser.| Remove refill cap and push the new refill into the dispenser until it clicks in place.

Close dispenser cover. The green status light will blink after closing, indicating the dispenser is ready to use.| Place palms approximately 2″ below dispenser, product will dispense within 1 second of sensor activation.

Disposal/Recycling

Insert a flat blade screwdriver into the slots on the refill collar and twist to separate the collar from the refill.| Unscrew the pump from the bottle and discard. Dispose/Recycle the PET bottle and collar.

Locking the dispenser with LOCK OR NOT’ Technology

Lock the dispenser by aligning the key with the keyhole on the top of the dispenser and push down until a click is heard.| Check for a successful lock by pressing the release buttons on side of the dispenser to see if the front cover releases and slides down. Once locked, the dispenser will remain in the locked state. To open a locked dispenser, insert the key into the keyhole and press down until the front cover is released.| The locked position visual is shown as a reference, the backplate does not need to be removed to lock the dispenser.

Disabling the Locking Mechanism

Open a locked dispenser by inserting the key into the keyhole on the top of the dispenser to release the front cover.| Remove the backplate by lifting the bottom right-hand corner in an upward and away motion.

Restore to the unlocked position by pushing the Attach the locking mechanisms toward the top of the dispenser.| Attach the backplate by pressing on the top two corners and the bottom middle section.

TRUE FITTM Wall Plate and MESSENGERTM Dispenser Station Installation
The TRUE FIT & MESSENGER Station are optional accessories that can be utilized with the dispensing systems.
Use the TRUE FIT Wall Plate to cover any wall damage from removing old dispensers.
The MESSENGER Station lets you add a sign to promote good hand hygiene.

Install the TRUE FIT wall plate at the designated anchor holes. Place the TRUE FIT wall plate between the dispenser and the wall during installation.| Slide two prongs at the bottom of the MESSENGER Dispenser Station into the inlet holes above TRUE FIT Wall Plate until they set in. The MESSENGER Dispenser Station accepts a standard 3″x4″ clear name badge holder with a 3″x 4″ name badge card that can be ordered from most office supply vendors. Print a message on a 3″x 4″ name badge card and insert the message between the frame and back with message facing out.

Order this wall plate if you aren’t using a MESSENGER Station.

7740-GPH-18 TRUE FIT Wall Plate – Graphite

7740-WHT-18 TRUE FIT Wall Plate – White

The MESSENGER Station includes a Wall Plate.

7741-GPH-18 TRUE FIT Wall Plate + MESSENGER Dispenser Station – Graphite 7741-WHT-18 TRUE FIT Wall Plate + MESSENGER Dispenser Station – White

Dispenser Status LED
Green Flash – every 7 seconds = good
NO LED – batteries need to be replaced
– no refill installed

Warnings
Use dispenser only as directed.
Do not use in areas where dispensers may be exposed to wet environments such as showers or outdoors.
Do not install or use in extreme hot or cold locations.
Dispensed product intended for external use only. Refer to refill for actions in case of ingestion.

Cleaning and Maintenance
Clean the exterior surfaces of the dispenser using warm water and mild soap.
DO NOT USE ABRASIVE CLEANERS.
Dry with a soft cloth.

Troubleshooting

No Dispensing, Motor Does Not Run

• Hands are not directly beneath the sensor
• No refill is loaded No

Dispensing, Motor Runs

• Refill is empty or loaded incorrectly
• The refill pump is not primed

Rated 6Vdc
Battery Operated Appliance
Classification, per UL 60601-1
Internally Powered
Type B Applied Part
IXPO
Not suitable for use in the presence of a flammable anesthetics

G010 Industries, Inc.
One GOJO Plaza, Suite 500
P.O. Box 991 • Akron, OH. 44309-0991
Tel. : 1-330-358:00 Sas al; : 1a:0321-9547
Telecopieur : 1-800-FAX-G0.10
©2018. GOJO Industries, Inc. Tous droits reserves.

Documents / Resources

| Purell ES6 Soap and Sanitizer Touch Free Dispenser [pdf] Instruction Manual
ES6, Soap and Sanitizer Touch Free Dispenser, ES6 Soap and Sanitizer Touch Free Dispenser
---|---

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>