HOME DECORATORS COLLECTION 28025-HBOS 4-Light LED Vanity Light Bar User Guide

28025-HBOS 4-Light LED Vanity Light Bar
User Guide
Item #1006 355 017
Model # 28025-HBOS

THANK YOU
We appreciate the trust and confidence you have placed in Home Decorators Collection through the purchase of this 4-light LED vanity light. We strive to continually create quality products designed to enhance your home. Visit us online to see our full line of products available for your home improvement needs. Thank you for choosing Home Decorators Collection!

Safety Information

• Read all the instructions before assembling and installing.
• Consult a qualified electrician for installation of this fixture.
• If you have any non-electrical questions about this fixture, please contact our Customer Service Team at 1-800-986-3460 or visit www.homedepot.com/homedecorators.
• Please reference your Item #1006 355 017 or UPC 773546310055.
• Keep your receipt and these instructions for proof of purchase.

| CAUTION: Before starting installation of this Fixture or removal of a previous Fixture, disconnect the power by turning off the circuit breaker or by removing the fuse at the fuse box.
---|---
| IMPORTANT: Inspect the wire insulation for any cuts, abrasions, or exposed copper that have occurred during shipping. If there is a defect in the wire, do not continue the assembly process. Please call our Customer Service Team at 1-800-986-3460.
| IMPORTANT: Do not install this lighting system in a wet locations.

Warranty

LIMITED WARRANTY
WHAT IS COVERED
The manufacturer warrants this lighting fixture to be free from defects in materials and workmanship for a period of three (3) years from date of purchase. This warranty applies only to the original consumer purchaser and only to products used in normal use and service. If this product is found to be defective, the manufacturer’s only obligation, and your exclusive remedy, is the repair or replacement of the product at the manufacturer’s discretion, provided that the product has not been damaged through misuse, abuse, accident, modification, alteration, neglect, or mishandling.
WHAT IS NOT COVERED
This warranty shall not apply to any product that is found to have been improperly installed, set up, or used in any way not in accordance with the instructions supplied with the product. This warranty shall not apply to a failure of the product as a result of an accident, misuse, abuse, negligence, alteration, faulty installation, or any other failure not relating to faulty material or workmanship. This warranty shall not apply to the finish on any portion of the product, such as surface and/or weathering, as this is considered normal wear and tear. The manufacturer does not warrant and specifically disclaims any warranty, whether express or implied, of fitness for a particular purpose, other than the warranty contained herein. The manufacturer specifically disclaims any liability and shall not be liable for any consequential or incidental loss or damage, including but not limited to any labor/expense costs involved in the replacement or repair of said product.

Contact the Customer Service Team at 1-800-986-3460 or visit www.homedepot.com/homedecorators.

Pre-Installation

PLANNING INSTALLATION
Read all instructions before assembly and installation. To avoid damaging this product, assemble it on a soft, non-abrasive surface, such as carpet or cardboard. Inspect each part for defects that may have occurred during shipping. Keep your receipt and these instructions for proof of purchase.
TOOLS REQUIRED

| |
---|---|---
Safety goggles| Phillips screwdriver| Flathead screwdriver
| |
Wire strippers| Wire cutters| Ladder

HARDWARE INCLUDED
NOTE: Hardware not shown to actual size.

PACKAGE CONTENTS

Installation

1. Installing the bubble glass
   □ Carefully unpack the fixture. Lay out all the parts on a clean surface.
   □ Attach the bubble glass (B) to the fixture body (A). Then tighten the fixing screw (HH) by using the hexagon screwdriver (II).
   □ The glass hole must be installed facing the direction of the fixture body (A).

2. Installing the universal crossbar
   WARNING: Turn off the power at the main fuse box.
   □ Remove the backplate (EE) from the fixture body (A). Using the backplate (EE) as a guide, mark on the wall with the junction box (not included) the locations for anchors (GG) with a pencil (not included).
   □ Drill a 1/4 in. hole at marks, then insert anchors (GG). Secure the backplate (EE) to the junction box with the junction box screws (BB).
   □ Align the keyholes in the backplate (EE) with the anchors (GG) and insert the tapping screws (FF).

3. Making the electrical connections
   NOTE: Always use the wire nuts (AA) to connect wires and push all excess wires and connections back into the junction box (not included).
   □ Fasten the open end of the ground wire (bare copper or green wire) to the ground wire from the junction box or the ground screw (CC) on the backplate (EE).
   □ Connect the black wire of the power supply to the black wire of the fixture and connect the white wire of the power supply to the white wire of the fixture. □ Connect the fixture wires as follows:

4. Installing the fixture body
   □ Attach the fixture body (A) to the backplate (EE). Then tighten the mounting screws (DD) by using the Phillips screwdriver (not included).

FCC Statement

WARNING: Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio TV technician for help.

Company Name: Eurofase Inc.
Company address: 60 Industrial Parkway, Unit 802, Cheektowaga, NY 14227-2713
Telephone Number: 905.695.2055 x 259

Care and Cleaning

• Clean the light fixture carefully with a soft, dry cloth. Do not use any cleaners with chemicals, solvents, or harsh abrasives.

Troubleshooting

ON position.
The fuse blows or the circuit breaker trips when the light is turned on.| There are too many items on one circuit.| □ Unplug the other items on the circuit.
□ Contact a qualified electrician or call the Customer Service Team at
1-800-986-3460.

Questions, problems, missing parts? Before returning to the store, call Home Decorators Collection Customer Service
8 a.m. – 7 p.m., EST, Monday – Friday, 9 a.m. – 6 p.m., EST, Saturday
Please contact 1-800-986-3460 for further assistance.
WWW.HOMEDEPOT.COM/HOMEDECORATORS
Retain this manual for future use.

References

• Home Decorators Collection - Home Decor - The Home Depot

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>