Welotec 505-0000-517 Industrial Ethernet Switch User Manual

Welotec 505-0000-517 Industrial Ethernet Switch User Manual

Thank you for purchasing this industrial Ethernet switch. Please read this Manual carefully before proper and quick installation and full use of this product.

Packing list

The opened box of switch should contain the following products and accessories:

• An Ethernet switch
• Terminals
• User’s Manual & Warranty Card & Conformity Certificate

Note : After opening the product package, if you find that any of the above product and accessories is missing or damaged, please contact your dealer or sales personnel in time.

product introduction

This series of industrial switches is our product for the security industry, which is easy to be managed and maintained, and meets the networking and access requirements of small and medium-sized enterprises, intelligent communities, hotels, office networks and campus networks. The series is available in a variety of products with DIN rail mounting to meet the needs of different application sites. The dial switch design allows for rapid configuration and supports multiple operating modes: VLAN, ring network and long distance 10M. The 8-port POE model is equipped with 1-2 port green VIP channel. The QOS priority function can ensure the transmission priority of important data. The power input is supported by two independent power supply circuits, to ensure that the device can still operate normally when any circuit of power supply fails. The hardware is designed to be fan-free and subject to low power consumption, and wide temperature and voltage range, and is qualified in strict tests in accordance with industry standards to be adapted to the industrial site environment with severe requirements for EMC, and can be widely used in intelligent transportation, highway, smart city, safe city, new energy, intelligent manufacturing, and other industrial fields.

Product properties

• Working temperature: -40 – 85 °C, storage temperature: -40~85ºC
• Power supply: supporting 2 power inputs
• IP40-rated protection, high-strength corrugated aluminum enclosure
• DN rail mounted, fan-free
• Copper port: 10/100/1000Base, RJ45, automatic flow rate control, full/half duplex mode, MDI/MDI-X auto-detection
• Vibration: IEC 60068-2-6 shock: IEC 60068-2-27 free fall: IEC 60068-2-32
• Applicable standards: IEEE802.3, IEEE802.3u, IEEE802.3z, IEEE802.3ab standards
• EMC anti-interference: Excellent lightning protection, anti-static and anti-interfer – ence capability
• Certification: CE, FCC, ROHS, test report of the Ministry of Public Security
• A warranty of 5 years

Description of switch indicator

The indicators of switch are described in detail as below.

Installation and disassembly of switch

“Installation of DIN rail”

Step1 ： The guide rails are mounted as follows: Check that the DIN-rail connector that comes with the device is securely installed.
Step2 ： Snap the lower part of the DIN-rail connector, i.e. the side with spring support, into the DIN rail, then snap the upper part of the DIN-rail connector into the DIN rail.

Tips:
Snap the lower part by a little and gently lift upward the connector to snap the upper part.

Step3 ： Check and confirm that the product is reliably mounted to the DIN rail and the installation is completed.

Figure 1. Schematic diagram of the side installation of the switch

“Disassembly of DIN rail”

Step1 : The device is powered off
Step2 : Gently lift the device upwards, remove the upper part from the DIN rail connector, and then the lower part from the DIN rail connector to finish the disassembly

Switch power up

The series provides 5-position input terminals and two sets of DC power supply system (P1 and P2), which can be used individually, or along with two external and independent DC power supply systems. Power supply range: 9VDC – 48VDC (POE series 48-57VDC, POE pin: V+, V+, V-, V- corresponding pins 1,2,3,6)

Figure 3. Schematic diagram of ground wire

Grounding: Fix the grounding wire to the grounding screw above the switch to ensure a reliable connection of a good grounding system.

Manage switches

Managed switch series

Managed series: The switch provides web-based management login, which allows users to log in to the switch through a web page. The default IP address of the switch is 192.168.1.254 and both the default account and password are admin. In addition, a 2-digit dial switch is designed with ON to enable and OFF to disable. The dial switch is defined as follows:

Reset Key:
Keep the device turned on and press the button for about 5 seconds. The system restores the default factory settings.

Unmanaged switch series
The unmanaged switch provides a 2-digit dial switch, with ON to enable and OFF to disable, defined as follows:

Optional models of products

Ppot rct

5 Gigabit copper port| Guide rail| /| 5| /| /
8 Gigabit copper port| Guide rail| /| 8| /| /
1 Gigabit SFP fiber ports, 1 Gigabit copper port| Guide rail| /| 1| /| 1
1 Hundred Megabit 1×9 fiber port, 4 Hundred Megabit copper ports| Guide rail| 4| /| 1| /
1 Gigabit SFP fiber ports, 4 Gigabit copper port| Guide rail| /| 1| /| 4
1 Gigabit SFP fiber ports, 8 Gigabit copper port| Guide rail| /| 1| /| 8
2 Gigabit SFP fiber ports, 4 Gigabit copper port| Guide rail| /| 4| /| 2
2 Gigabit SFP fiber ports, 8 Gigabit copper port| Guide rail| /| 8| /| 2
4 Gigabit SFP fiber ports, 8 Gigabit copper port| Guide rail| /| 8| /| 4
Guide rail POE model| Strtuycpteure| Port
4 POE ports are connected with 1 light and 1 power in Gigabit| Guide rail| /| 5| /| 1
4 POE ports 2 Gigabit SFP| Guide rail| /| 4| /| 2
8 POE ports are connected with 1 light and 1 power in Gigabit| Guide rail| /| 9| /| 1
8 POE ports 2 Gigabit SFP| Guide rail| /| 8| /| 2

Note : network management and non-network management are optional.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>