milwaukee M12 FPDX Cordless Percussion Drill or Driver Instruction Manual

milwaukee M12 FPDX Cordless Percussion Drill or Driver

Product Information

The M12 FPDX is a Milwaukee powerbase that comes with a selection of different application heads. The equipment package that you purchase will determine the type of application heads that come with it. Other application heads and powerbases can be purchased separately.

The product user manual includes a technical data section, important safety and working hints, and descriptions of symbols.

Product Usage Instructions

1. Before starting any work on the machine, remove the battery pack.
2. For all work on the machine, remove the battery pack.
3. Refer to the overview in the manual to select the appropriate combination of application heads for your needs.
4. Check the plug and power cord for any damage before use. Only a specialist should repair any damage.
5. Follow the instructions in the manual for attaching and using the selected application head.
6. Press the “start” button to begin use and the “stop” button to end use.
7. The LED display shows the battery level and power percentage during use.

Original instructions

Picture section with operating description and functional description

Remove the battery pack before starting any work on the machine.

The overview shows a selection of diff erent application heads to this Milwaukee powerbase.
Depending on the equipment package you have purchased various application heads. Other application heads and powerbases can be purchased separately.
Use only the imaged application combinations of application heads.

Handle (insulated gripping surface)

TECHNICAL DATA

• Production code ………………………………………………………………………………………………………………………………………………..4673 25 03… …000001-999999
• Drilling capacity in steel………………………………………………………………………………………………………………………………………….. 13 mm
• Drilling capacity in wood ………………………………………………………………………………………………………………………………………… 35 mm
• Drilling capacity in brick and tile ………………………………………………………………………………………………………………………………. 13 mm
• Wood screws (without pre-drilling) …………………………………………………………………………………………………………………………….. 8 mm
• No-load speed 1st gear ……………………………………………………………………………………………………………………………………… 0-450 min-1
• No-load speed 2nd gear ………………………………………………………………………………………………………………………………….. 0-1700 min-1
• Impact rate 1st gear ………………………………………………………………………………………………………………………………………… 0-6750 min-1
• Impact rate 2nd gear ……………………………………………………………………………………………………………………………………… 0-25500 min-1
• Torque with battery (1.5 Ah / 2.0 Ah) *1 ……………………………………………………………………………………………………………………. 37 Nm
• Torque with battery (3.0 Ah / 4.0 Ah) *1 ……………………………………………………………………………………………………………………. 44 Nm
• Battery voltage ……………………………………………………………………………………………………………………………………………………… 12 V
• Drill chuck range ……………………………………………………………………………………………………………………………………………… 1,5-13 mm
• Weight according EPTA-Procedure 01/2014 (1.5 Ah / 2.0 Ah) ………………………………………………………………………………….. 1,24 kg
• Weight according EPTA-Procedure 01/2014 (3.0 Ah / 4.0 Ah) ………………………………………………………………………………….. 1,47 kg
• Recommended ambient operating temperature …………………………………………………………………………………………………..-18°C … +50 °C
• Recommended battery types …………………………………………………………………………………………………..M12-18 C; M12-18 FC; M12-18 AC; M12 C4; C12 C

Noise/vibration information
Measured values determined according to EN 62841.
Typically, the A-weighted noise levels of the tool are:

• Sound pressure level (Uncertainty K=3dB(A)) ………………………………………………………………………………………………………….. 89 dB (A)
  Sound power level (Uncertainty K=3dB(A)) …………………………………………………………………………………………………………….. 100 dB (A)

Always wear ear protectors!
Total vibration values (vector sum in the three axes) determined according to EN 62841.
Vibration emission value ah

• Percussion drilling into concrete ah,ID ………………………………………………………………………………………………………………. 15,73 m/s2
• Uncertainty K= …………………………………………………………………………………………………………………………………………………. 1,5 m/s2
• Drilling into metal ah,D………………………………………………………………………………………………………………………………………. 1,92 m/s2
• Uncertainty K= …………………………………………………………………………………………………………………………………………………. 1,5 m/s2
• Screwing ah,S………………………………………………………………………………………………………………………………………………….. 0,86 m/s2
• Uncertainty K= …………………………………………………………………………………………………………………………………………………. 1,5 m/s2

*1 Measured according to Milwaukee standard N 877318

WARNING
The vibration and noise emission level given in this information sheet has been measured in accordance with a standardized test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration and noise emission level represents the main applications of the tool. However if the tool is used for diff erent applications, with diff erent accessories or poorly maintained, the vibration and noise emission may diff er. This may signifi cantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration and noise should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may signifi cantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration and/or noise such as: maintain the tool and the accessories, keep the hands warm, organization of work patterns.

WARNING Read all safety warnings, instructions, illustrations and specifi cations provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.

DRILL SAFETY WARNINGS

Safety instructions for all operations
Hold the power tool by insulated gripping surfaces, when performing an operation where the cutting accessory or fasteners may contact hidden wiring.
Cutting accessory or fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.
Wear ear protectors when impact drilling. Exposure to noise can cause hearing loss.

Safety instructions when using long drill bits
Never operate at higher speed than the maximum speed rated of the drill bit. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting the personal injury.
Always start drilling at low speed and with the bit tip in contact with the workpiece. At higher speeds, the bit is likely to bend if allowed to rotate freely without contacting the workpiece, resulting the personal injury.
Apply pressure only in direct line with the bit and do not apply excessive pressure. Bits can bend causing breakage or loss of control, resulting in personal injury.

SCREWDRIVER SAFETY WARNINGS

Hold the power tool by insulated gripping surfaces, when performing an operation where the fastener may contact hidden wiring. Fasteners contacting a “live” wire may make exposed metal parts of the power tool “live” and could give the operator an electric shock.

ADDITIONAL SAFETY AND WORKING INSTRUCTIONS

Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.
The dust produced when using this tool may be harmful to health. Do not inhale the dust. Wear a suitable dust protection mask.
Do not machine any materials that present a danger to health (e.g. asbestos).
Switch the device off immediately if the insertion tool stalls! Do not switch the device on again while the insertion tool is stalled, as doing so could trigger a sudden recoil with a high reactive force. Determine why the insertion tool stalled and rectify this, paying heed to the safety instructions.
The possible causes may be:

• it is tilted in the workpiece to be machined

• it has pierced through the material to be machined

• the power tool is overloaded

• Do not reach into the machine while it is running. The insertion tool may become hot during use.
  WARNING! Danger of burns

• when changing tools

• when setting the device down

• Chips and splinters must not be removed while the machine is running.

• When working in walls ceiling, or floor, take care to avoid electric cables and gas or waterpipes.

Clamp your workpiece with a clamping device. Unclamped workpieces can cause severe injury and damage.
Remove the battery pack before starting any work on the machine.
Do not dispose of used battery packs in the household refuse or by burning them. Milwaukee Distributors off er to retrieve old batteries to protect our environment.
Do not store the battery pack together with metal objects (short circuit risk). Use only System M12 chargers for charging System M12 battery packs. Do not use battery packs from other systems.
Never break open battery packs and chargers and store only in dry rooms. Keep dry at all times.
Battery acid may leak from damaged batteries under extreme load or extreme temperatures. In case of contact with battery acid wash it off immediately with soap and water. In case of eye contact rinse thoroughly for at least 10 minutes and immediately seek medical attention.
Warning! To reduce the risk of fi re, personal injury, and product damage due to a short circuit, never immerse your tool, battery pack or charger in fluid or allow a fluid to fl ow inside them. Corrosive or conductive fluids, such as seawater, certain industrial chemicals, and bleach or bleach containing products, etc., can cause a short circuit.

SPECIFIED CONDITIONS OF USE

The electronic battery percussion drill/screwdriver may be used for drilling, percussion drilling, as well as screwdriving for independent use away from mains supply.
Do not use this product in any other way as stated for normal use.

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that the product described under “Technical Data” fulfi lls all the relevant regulations and the directives 2011/65/EU (RoHS), 2014/30/EU, 2006/42/EC, and the following harmonized standards have been used:
EN 62841-1:2015
EN 62841-2-1:2018+A11:2019
EN 62841-2-2:2014
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN IEC 63000:2018
Winnenden, 2020-10-25
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany

GB-DECLARATION OF CONFORMITY

We declare as the manufacturer under our sole responsibility that the product described under “Technical Data” fulfi lls all the relevant provisions of the following Regulations S.I. 2008/1597 (as amended), S.I. 2016/1091 (as amended), S.I. 2012/3032 (as amended) and that the following designated standards have been used:
BS EN 62841-1:2015
BS EN 62841-2-1:2018+A11:2019
BS EN 62841-2-2:2014
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN IEC 63000:2018
Winnenden, 2020-10-25
Alexander Krug
Managing Director
Authorized to compile the technical fi le.
Techtronic Industries GmbH
Max-Eyth-Straße 10
71364 Winnenden
Germany

BATTERIES

Battery packs which have not been used for some time should be recharged before use.
Temperatures in excess of 50°C (122°F) reduce the performance of the battery pack. Avoid extended exposure to heat or sunshine (risk of overheating).
The contacts of chargers and battery packs must be kept clean.
For an optimum life-time, after use, the battery packs have to be fully charged.
To obtain the longest possible battery life remove the battery pack from the charger once it is fully charged.
For battery pack storage longer than 30 days:
Store the battery pack where the temperature is below 27°C and away from moisture
Store the battery packs in a 30% – 50% charged condition
Every six months of storage, charge the pack as normal.

BATTERY PACK PROTECTION

In extremely high torque, binding, stalling and short circuit situations that cause high current draw, the tool will vibrate for about 2 seconds and then the tool will turn OFF.
To reset, release the trigger.
Under extreme circumstances, the internal temperatur of the battery could become to high. If this happens, the battery will shut down.
Place the battery on the charger to charge and reset it.

TRANSPORTING LITHIUM BATTERIES

Lithium-ion batteries are subject to the Dangerous Goods Legislation requirements.
Transportation of those batteries has to be done in accordance with local, national and international provisions and regulations.

• The user can transport the batteries by road without further requirements.
• Commercial transport of Lithium-Ion batteries by third parties is subject to Dangerous Goods regulations. Transport preparation and transport are exclusively to be carried out by appropriately trained persons and the process has to be accompanied by corresponding experts.
• When transporting batteries:
• Ensure that battery contact terminals are protected and insulated to prevent short circuit.
• Ensure that battery pack is secured against movement within packaging.
• Do not transport batteries that are cracked or leak.
  Check with forwarding company for further advice

MAINTENANCE

Use only Milwaukee accessories and spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses).
If needed, an exploded view of the tool can be ordered. Please state the machine type printed as well as the six-digit No. on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max-Eyth-Straße 10, 71364 Winnenden, Germany.

SYMBOLS

• CAUTION! WARNING! DANGER!

• Remove the battery pack before starting any work on the machine.

• Please read the instructions carefully before starting the machine.

• Do not dispose electric tools, batteries/rechargeable batteries together with household waste material.
  Electric tools and batteries that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility.
  Check with your local authority or retailer for recycling advice and collection point.

• No-load speed

• Volts

• Direct current

• European Conformity Mark

• British Confomity Mark

• Ukraine Conformity Mark

• EurAsian Conformity Mark

References

• Milwaukee Tool Europe | Cordless Power Tools, Outdoor Tools, Hand Tools, PPE, Work wear. Storage and Accessories. | Milwaukee Tools Europe

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>