milwaukee ROS150E-2 Random Orbital Sander Instruction Manual

: October 30, 2023
: Milwaukee

Table of Contents

milwaukee ROS150E-2 Random Orbital Sander
Product Information
Product Usage Instructions
Accessories
Start/Stop
Using
TECHNICAL DATA
SANDER SAFETY WARNINGS
MAINS CONNECTION
SPECIFIED CONDITIONS OF USE
MAINTENANCE
DECLARATION OF CONFORMITY
SYMBOLS
CONTACT
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

milwaukee ROS150E-2 Random Orbital Sander

Product Information

The ROS 150 E-2 is a sanding machine designed for use on various surfaces. The machine comes with a fuzzy side sanding disc that needs to be carefully placed against the packaging pad. The machine has a VELCRO system that helps in easy and quick replacement of sanding discs. The product comes with technical data, safety instructions, specified conditions of use, EC-Declaration of Conformity, mains connection, maintenance, and symbols. Please read and save these instructions for future reference.

Product Usage Instructions

Press carefully the fuzzy side of the sanding disc against the packaging pad as firmly as possible.
Place the heightened side of the sanding pad carefully on the sanding disc and press it as tightly as possible.
Attach the sanding pad to the VELCRO system on the machine.
Plug in the machine to the mains connection.
Turn on the machine and start sanding the surface.
After use, turn off the machine and unplug it from the mains connection.
Clean the sanding pad and store it in a safe place for future use.

Tip

Accessories

Press carefully the fuzzy side of sanding disc against the packaging pad,as firmly as possible.

Orbital travel diameter

Start/Stop

Speed

Using

Tip

TECHNICAL DATA

Random Orbital Sander	ROS 150 E-2
Production code	4311 71 03…

4311 81 03…

… 000001-999999

Measured values determined according to EN 62841. Typically, the A-weighted noise levels of the tool are:

Sound pressure level (Uncertainty K=3dB(A)) Sound power level (Uncertainty K=3dB(A))

Wear ear protectors!

| 83,5 dB (A)

94,5 dB (A)

Vibration information

Vibration total values (triaxial vector sum) determined according to EN 62841

Vibration emission value ah Uncertainty K=| 6,1 m/s2

1,5 m/s2

WARNING

The vibration emission level given in this information sheet has been measured in accordance with a standardised test given in EN 62841 and may be used to compare one tool with another. It may be used for a preliminary assessment of exposure.
The declared vibration emission level represents the main applications of the tool. However if the tool is used for different applications, with different accessories or poorly maintained, the vibration emission may differ. This may significantly increase the exposure level over the total working period.
An estimation of the level of exposure to vibration should also take into account the times when the tool is switched off or when it is running but not actually doing the job. This may significantly reduce the exposure level over the total working period.
Identify additional safety measures to protect the operator from the effects of vibration such as: maintain the tool and the accessories, keep the hands warm, organisation of work patterns.

WARNING

Read all safety warnings, instructions, illustrations and specifications provided with this power tool. Failure to follow all instructions listed below may result in electric shock, fire and/or serious injury.
Save all warnings and instructions for future reference.

SANDER SAFETY WARNINGS

Wear ear protectors. Exposure to noise can cause hearing loss.
Use protective equipment. Always wear safety glasses when working with the machine. The use of protective clothing is recommended, such as dust mask, protective gloves, sturdy non-slip footwear, helmet and ear defenders.
Always disconnect the plug from the socket before carrying out any work on the machine.
The dust produced when using this tool may be harmful to health.
Do not inhale the dust. Use a dust absorption system and wear a suitable dust protection mask. Remove deposited dust thoroughly, e.g. with a vacuum cleaner.
Do not machine any materials that present a danger to health (e.g. asbestos).
This machine is suitable only for dry sanding.

MAINS CONNECTION

Connect only to single-phase AC system voltage as indicated on the rating plate. It is also possible to connect to sockets without an earthing contact as the design conforms to safety class II. Appliances used at many different locations including wet room and open air must be connected via a residual current device (FI, RCD, PRCD) of 30mA or less. Make sure the machine is switched off before plugging in. Keep mains lead clear from working range of the machine. Always lead the cable away behind you. Before use check machine, cable, and plug for any damages or material fatigue. Repairs should only be carried out by authorised Service Agents.

SPECIFIED CONDITIONS OF USE

This eccentric sander is a versatile machine. The following work can be carried out with it: Coarse sanding and grinding, Fine sanding and polishing, Rubbing down weather-beaten paint, Rubbing down weather-beaten paint, Polishing up scratches on acrylic glass, Etc.

ELECTRONICS

In case of overload, the rotational speed is being reduced until machine stops.
Please note that the machine will automatically accelerate back to its original operating speed if the load is removed from it.

MAINTENANCE

The ventilation slots of the machine must be kept clear at all times. Always disconnect the plug from the socket before carrying out any work on the machine.

If the supply cord of this power tool is damaged, it must be replaced by the manufacturer or his agent in order to avoid a safety hazard. Use only Milwaukee accessories and Milwaukee spare parts. Should components need to be replaced which have not been described, please contact one of our Milwaukee service agents (see our list of guarantee/service addresses). If needed, an exploded view of the tool can be ordered. Please state the Article No. as well as the machine type printed on the label and order the drawing at your local service agents or directly at: Techtronic Industries GmbH, Max‑Eyth‑Straße 10, 71364 Winnenden, Germany.

DECLARATION OF CONFORMITY

EC-DECLARATION OF CONFORMITY

We declare under our sole responsibility that the product described under “Technical Data” fulfills all the relevant provisions of the directives

2011/65/EU
2014/30/EU
2006/42/EC

and the following harmonized standards

EN 62841-1:2015
EN 62841-2-4:2014
EN 55014-1:2017+A11:2020
EN 55014-2:2015
EN 61000-3-2:2014
EN 61000-3-3:2013
EN IEC 63000:2018

Winnenden, 2020-11-14

Alexander Krug / Managing Director
Authorized to compile the technical file

Techtronic Industries GmbH

Max-Eyth-Straße 10, 71364 Winnenden, Germany

GB-DECLARATION OF CONFORMITY

We declare as the manufacturer under our sole responsibility that the product described under „Technical Data“ fulfills all the relevant provisions of the following Regulations S.I. 2012/3032 (as amended), S.I. 2008/1597 (as amended), S.I. 2016/1091 (as amended) and that the following designated standards have been used:

BS EN 62841-1:2015
BS EN 62841-2-4:2014
BS EN 55014-1:2017+A11:2020
BS EN 55014-2:2015
BS EN 61000-3-2:2014
BS EN 61000-3-3:2013
BS EN IEC 63000:2018

Winnenden, 2020-11-14

Alexander Krug / Managing Director
Authorized to compile the technical file

Techtronic Industries GmbH

Max-Eyth-Straße 10, 71364 Winnenden, Germany

SYMBOLS

CAUTION! WARNING! DANGER!
Please read the instructions carefully before starting the machine.
Always disconnect the plug from the socket before carrying out any work on the machine.
Do not use force.
Accessory – Not included in standard equipment, available as an accessory.
Do not dispose of electric tools together with household waste material. Electric tools and electronic equipment that have reached the end of their life must be collected separately and returned to an environmentally compatible recycling facility. Check with your local authority or retailer for recycling advice and collection point.
Class II tool. Tool in which protection against electric shock does not rely on basic insulation only, but in which additional safety precautions, such as double insulation or reinforced insulation, are provided. There being no provision for protective earthing or reliance upon installation conditions.
No-load speed
Volts
AC Current
European Conformity Mark
British Conformity Mark
Ukraine Conformity Mark
EurAsian Conformity Mark