AutoPot 80 Pot Watering System User Guide

: October 30, 2023
: AutoPot

Table of Contents

AutoPot 80 Pot Watering System
Product Information: GeoPot 80 System
Product Usage Instructions: GeoPot 80 System Setup
Simple care guidelines
Plan views and options
Suggested layouts
GeoPot 80 dimensions
GeoPot 80 System setup instructions
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

AutoPot 80 Pot Watering System

Product Information: GeoPot 80 System

The GeoPot 80 System is a plant growing system that consists of a tray, a pot sock, a 3/8 top hat grommet, a 3/8 pipe, an AQUAvalve5 with collar, and a lid. The system requires a minimum 200-gallon FlexiTank, which is supplied separately. The dimensions of GeoPot 80 are not mentioned in the manual.

The AQUAvalve5 is easily disassembled for cleaning with warm soapy water. The circular discs fitted to the top float can be removed using pliers to grip the raised point. It is advisable to remove the silicone to avoid them being lost. It is also recommended to use a paper clip or pipe cleaner to push through the AQUAvalve5 nozzle to remove any lime scale build-up that may have occurred during the growing season. Blowing through the AQUAvalve5 nozzle will also help to remove any build-up. However, it is advised not to use a drill and drill bit to clear the AQUAvalve5 nozzle as this may potentially damage the AQUAvalve5 beyond repair.

Product Usage Instructions: GeoPot 80 System Setup

Fit PotSock over the base of GeoPot.
Fill GeoPot with medium and pot up plants. Water through pot and allow draining outside the tray. Brush off debris.
From the outside of the module tray, push the 3/8 top hat grommet into the hole in the module tray wall. Thread approximately 12 inches of 3/8 pipe into the tray through the grommet. Wetting the pipe end will aid insertion. Remove AQUAvalve collar.
Push 3/8 pipe through the collar and attach it to AQUAvalve nozzle. Rescrew collar – DON’T overturn…when you feel it grip STOP.
Align the ‘half moon’ section on the rear of the AQUAvalve with the ‘T’ section in the tray. Firmly push the AQUAvalve onto the ‘T’. Remove any slack in the 3/8 pipe by drawing excess out of the tray.
Cut 3/8 / 1/2 pipe to appropriate length according to the size of your system. Connect your 3/8 / 1/2 pipe to relevant fitting or tank.
Place GeoPot in the tray. Ensure NO FABRIC IS TOUCHING AQUAVALVE. Place the lid over the valve onto the tray.
Using your front instruction sheet, repeat the module set up instructions for the number of trays.
Allow your plants to establish for 7-10 days before turning the system on.

To ensure proper functioning of the AQUAvalve5, hold it at eye level so that you can see the silicone fitted to the top float resting on the hole below it. The silicone must create a tight seal when touching the hole. If it looks like it is not sitting parallel on the hole below, lift the top float and apply pressure to one side of the silicone, drop the float, and hold at eye level again. Repeat the procedure if necessary.
At the end of your growing season, clean the AQUAvalve5 using warm soapy water. Use an old toothbrush to clean it.
If you have any queries or need advice, contact info@autopot- usa.com or visit www.autopot- usa.com. You can also call +(1) 702-338-0373.

Simple care guidelines

Ensuring that the AQUAvalve5 floods and drains correctly

Making sure your AQUAvalve5 floods and drains correctly is simply achieved and only takes a few seconds.
Hold the AQUAvalve5 at eye level so that you can see the silicone fitted to the top float resting on the hole below it.
The silicone must create a tight seal when touching the hole.
If it looks like it is not sitting parallel on the hole below, simply lift the top float and apply pressure to one side of the silicone, drop the float and hold at eye level again. Repeat the procedure if necessary.

Care and maintenance

At the end of your growing season, clean the AQUAvalve5 using warm soapy water. Using an old tooth brush will help. The AQUAvalve5 is easily disassembled. The top float will slide all the way across and the bottom float is unclipped from its pivoting position. The circular discs fitted to the top float can also be removed by using pliers to grip the raised point. At this point is it advisable to remove the silicones to avoid them being lost.
It is also handy to have a paper clip or pipe cleaner to hand so that you can push it through the AQUAvalve5 nozzle, this will remove any lime scale build up that may have occurred during the growing season. Blowing through the AQUAvalve5 nozzle will also help to remove any build up. Do not under any circumstances use a drill & drill bit to clear the AQUAvalve5 nozzle. This will potentially damage the AQUAvalve5 beyond repair.

Plan views and options

GeoPot 80 System contents

1x 200 gal FlexiTank
80x 1Pot XL tray and lid
80x 3 gal or 5 gal GeoPot
80x AQUAvalve5
80x 3/8” top hat grommet
1x 1/2” tank adapter and filter
4x 1/2” in-line tap
40x 1/2” – 3/8” cross connector
3x 1/2” tee connector
98ft of 1/2” pipe
131ft of 3/8” pipe
80x PotSock Round

Suggested layouts

System requires minimum 200 gal FlexiTank (supplied)

Advice

Please note that multiple GeoPots may increase room humidity due to the exposed surfaces of the fabric pots.
Pot up your plants, water through, then allow your plants to establish in the pots for a period of 7 to 10 days before turning your system on. This will encourage a stronger and healthier root system.
Always raise your reservoir to a minimum of 6” above the highest AQUAvalve5 and re-fill the reservoir when there is approximately a 1/3 of the solution left – NEVER ALLOW THE RESERVOIR TO RUN EMPTY.
With AQUAvalve5 systems mineral or organic fertilisers may be fed via the reservoir and pipework. Organic fertilisers will require a water pump in the reservoir running for 15 mins every 2 hrs and cleaning of the reservoir, pump, and filter each time the reservoir empties. Flush pipework with plain water every time the reservoir empties.
Clean all substrate from the bottom and sides of the pots before placing in each tray. This will ensure your system is clean from the start.
Always use free draining substrates, for example: soil/perlite, coco/perlite, soil/clay pebbles, coco/clay pebbles, rockwool/clay pebbles.

GeoPot 80 dimensions

GeoPot 80 System setup instructions

Fill GeoPot with medium and pot up plants.
Fit PotSock over the base of GeoPot
Water through pot and allow to drain outside the tray. Brush off debris.
From the outside of the module tray push the 3/8” top hat grommet into the hole in the module tray wall.
Thread approx 12” of 3/8” pipe into the tray through the grommet.
Wetting the pipe end will aid insertion.
Remove AQUAvalve collar
Push 3/8” pipe through collar and attach to AQUAvalve nozzle
Rescrew collar – DON’T overturn… when you feel it grip STOP
Remove any slack in the 3/8” pipe by drawing excess out of the tray.
Align the ‘half moon’ section on the rear of the AQUAvalve with the ‘T’ section in the tray.
Firmly push the AQUAvalve onto the ‘T’.
Cut 3/8” / 1/2” pipe to appropriate length
According to the size of your system connect your 3/8” / 1/2” pipe to relevant fitting or tank…
Place GeoPot in tray.
Ensure NO FABRIC IS TOUCHING AQUAVALVE
Place lid over valve onto tray.

Using your front instruction sheet, repeat the module set up instructions for the number of trays. Allow your plants to establish for 7-10 days before turning system on

Advice: If you require any guidance email – info@autopot- usa.com

info@autopot-usa.com I www.autopot- usa.com I +(1) 702-338-0373