OLG LXHDPKG 1 B Luxe Home Desk Instruction Manual

October 30, 2023
OLG

OLG LXHDPKG 1 B Luxe Home Desk Instruction Manual
Luxe Home Desk

Parts List:

  • Glass Tempered Table Top
    Table Top

  • Stainless Steel Table Frame
    Table Frame

  • Foot Plate w/ adjustable foot

  • 8 – M6 x 16

  • 8 – M8 x 16

Tools included:

M5

Tools required:
Tools required

Specifications

Elecrtic control part:
Input Voltage: 100-240Vac 50/60Hz
Duty cycle: 10%MAX 2min on 18min off

Desk frame part:
Dynamic load: 60KG
The maximum static load: 80KG

Safety warning

  1. Please read this manual carefully before use.
  2. The product must be connected to the correct power supply.
  3. For any accessories connected to the control box, the plug typeand electrical characteristics must conform to its specifications.
  4. Indoor use only.
  5. If the transformer’s external cable is damaged and need to bereplaced,new accessory will be provided by the manufacturer orits service agent.
  6. This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
  7. Children shall not play with the appliance.
  8. Cleaning and user maintenance shall not be made by children without supervision.

STEP 1:
Installation
STEP 2:
Installation
STEP 3:
Installation
STEP 4:
Installation
Complete
Complete

The whole handset surface is a touch panel. If there is no touch within 10 seconds, the screen is locked and all keys are locked correspondingly. You can touch “ ” keys to unlock screen. When screen lightened, all keys unlocked and handset enter operation state.
Instruction

Display Screen
Display the height value of the desk.

Up & Down Key
Please keep pressing UP/DOWN key to adjust desk height until you get an optimum height.

Memory Key
After seting memory keys, the desk can lift automatically to memory height.

How to Set Memory Mode
Click the “ “ key when running to a specific point. The display screen displays “S-” and “-” flashes. At this time, press “ “ button to store the position to the corresponding label. the memory height is successfully saved,Then light press “ “ , the desk moves to memory height automatically.

Set Key
Press the “ “ key when memory bits and internal parameters need to be set.

Initialisation

  1. When “RST” is on the display screen, press the “ ” button until the desk frame reaches its lowest point. After hearing the “di” sound and desk frame rebounds, initialization is completed. (P.S. The button cannot be released during this operation, otherwise the initialization will fail)
  2. Forced initialization: Press the “ ” button until the desk frame reaches its lowest point, then release the button and press it again for about 5 seconds until hear the “di” sound and desk frame rebound, and the initialization is completed.
  3. Restore the factory settings: When new controller is changed or the parameters need to be restored to the factory settings, press the “ ” and “ ” buttons simultaneously, you will hear the first “di” sound after about 5 seconds and second “di” sound after 10 seconds. When the display screen shows “RST”,

Safety Function
When the desktop is on the rise or down, encountered reverse resistance,the desk will rebound.

Handset shows error code and solution

Error code Fault cause Solution
E01,E06,E07 Power fault Change power
E02 Psynchronous height over 1cm Implement the initialization operation 1
E04 Handset fault Unplug and replug the cable of hand set
E05 Anticollision alert Rebound reminder , normal condition
E08 Desktop sloping check the desktop
E11,E21,E40,E41 Connection cable failure Check the connecting cable
E12,E22,E42,E43 Controller fault Exchange the controller
E18,E28 Motor fault change motor
E18,E28 Overloading reduce the loading
HOT Overtime operation Automatic recovery after stop using for 20 minutes

Advanced Function Settings
Limited height setting:Press “ ” and “ ” key for 5 seconds till heard a bee sound, limited height setting success. (minimum limited height 96 maximum limited height 97). Cancel the function, run to the limit height, press “ ” and “ ” again for 5 seconds, hear the buzzer sound,  limited height Cancel.

Pressing “ ” key for 5 second till digital screen display “S-1“ , press “ ” or “ ” key to choose

Diagram

Sydney 02 8188 2732
Melbourne 03 9111 0315
Brisbane 07 3733 1923
Adelaide 08 7111 0810
Perth 08 9468 2707
info@olgoffice.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals