iLOQ H50S Padlock User Guide
- October 30, 2023
- iLOQ
Table of Contents
H50S Padlock User Guide
iLOQ S5 / S50
H50S.x31.HC
H50S.x41.HC
H50S Padlock User Guide
05/2023 Rev. 2.0
Document ID 189730
iLOQ Oy support.iloq.com
Safety Information
2.1 Safety signs
| Sign | Description |
|---|---|
| General notice sign. Indicates particularly important information about the |
installation or product.
| Read these instructions carefully before using products. This information is
to ensure your safety and long lifetime of the products.
Overview
The iLOQ H50S is a battery-free, programmable electro-mechanical padlock is a part of the iLOQ S50 product family and can be programmed to the iLOQ 5 Series locking system. The padlock is available with different shackle lenghts (grade 3: 25 /60/100 mm, grade 4: 28/50 mm & grade 5: 27/50 mm). The H50S padlocks are NFC-powered, no batteries are required. Two different versions are available: the H50S.x31 is unlocked and locked with a key and the H50S.x41 is lockable without a key.
Before installation
4.1 General notes
- The instructions should be carefully followed during installation. If there are any deviations from the contents in foreign language versions of the documentation, the English original shall apply in case of doubt.
- These instructions and any maintenance instructions should be passed on by the installer to the user.
- The H50S iLOQ Padlocks must be installed and used effortlessly without the use of excessive force. Do not drop the product.
- Do not modify the product in any way, except in accordance with those modifications described in these instructions.
- All components necessary for the specific installation should be fitted.
- The padlock has a 24 month warranty.
- The key has to be kept securely so that only an authorized person may have access.
- In case of losing a key, blocklisting of the lost key shall be done with the iLOQ Manager software and affected locks shall be reprogrammed.
- We reserve the right to make modifications or further technical developments without further notice.
4.2 Care & maintenance
The product is designed to be maintenance-free. It does not require any
regular maintenance.
4.3 After installation
Test the padlock functionality after installation to ensure that it does not
prevent the lock application from working properly.
Installation
- Install the padlock so that it hangs freely and cannot be submerged in water.
- Use a rain cover (iLOQ A10.73 or A10.74) to ensure the longevity and functionality of the padlock.\
- An accessory chain (iLOQ AH50.10, AH50.11 or AH50.12) can be used to secure the padlock to the installation site.
Operating instructions for iLOQ H50S
Before using the locks, please check the location of the NFC antenna in your
phone to know the best position to hold the phone against the lock-reader
knob. Information may be available in the datasheet of your phone. With
Android mobile phones you may be able to check the NFC antenna location from
the mobile phones NFC menu/information.
Note! Due to large variety of NFC enabled phone models and operating
system versions, iLOQ cannot guarantee that all NFC-enabled phones will work
seamlessly with our locks.
6.1 Opening
To open the H50S
padlock, you can either use:
- An iLOQ S50 Key Fob (with a valid access right), by placing the Key Fob in the middle of the black knob as shown on the left hand side picture.
- A mobile phone with an NFC capability, by placing the NFC aerial in the middle of the knob, as shown on the right hand side picture.
- Present a valid key to the reader knob to activate the lock. Wait until the key shows a green light to indicate that the lock is unlocked.
- Turn the reader knob clockwise 180°. The lock stays in the open-status for 5 to 15 seconds and automatically returns back to the locked-status if not opened (depending on the configured lock opening time).
- Pull the shackle open.
6.2 Closing
6.2.1 Locking manually (H50S.x41 versions)
-
Close the shackle.
-
Turn the reader knob 180° counterclockwise.
-
After closing the lock, ensure that the knob is in locked position and the padlock remains closed.
6.2.2 Locking with a key (H50S.x31 versions)
- Close the shackle.
- Present a valid key to the reader knob to activate the lock. Wait until the key shows a green light to indicate that the lock is unlocked.
- Turn the reader knob 180° counterclockwise. The lock stays in the open-status for 5 to 15 seconds and automatically returns back to the locked-status if not opened (depending on the configured lock opening time).
- After closing the lock, ensure that the knob is in locked position and the padlock remains closed.
Replacing the reader knob
If the reader knob is e.g. damaged and needs a replacement knob, please follow these instructions to replace the reader knob correctly.
- Loosen the fixing screw (with a T10 screwdriver) and pull the knob off.
- Before installing the new knob, add a small amount of CRC silicon grease to the knobs IP gasket.
- Insert the new knob on and tighten the fixing screw (1.5 Nm).
Disposal of decommissioned products
| Never discard an electrical appliance in household waste. Follow the local
laws and regulations for safe and environmentally friendly product disposal.
---|---
| Before discarding products, bear in mind that most iLOQ products are
reusable. All programmable products can be reset to factory settings, after
which they can be reused in another system.
Recycling instructions of decommissioned products are depicted below.
| Decommisioned product | Sorting |
|---|
Decommissioned iLOQ fittings, mounting accessories and thumb turn knobs can be
recycled as scrap metal.|
Decommissioned iLOQ products containing electronics and circuit boards, such
as iLOQ Lock Cylinders, keys, net bridges, door
modules, key and RFID readers, and relay cards, must be recycled at an
electrical and electronic equipment collection point.|
iLOQ products containing batteries and accumulators, such as key fobs,
programming keys and clock circuits, should be recycled at a regional
collection point for batteries and small accumulators.|
Most iLOQ packaging materials are suitable for cardboard and plastic
recycling.|
Compliance
iLOQ H50S Padlocks, including following product variants: H50S.331.110.HC,
H50S.331.15HC, H50S.331.25.HC, H50S.331.60.HC, H50S.341.110.HC,
H50S.341.15.HC, H50S.341.25.HC, H50S.341.60.HC, H50S.431.28.HC,
H50S.431.50.HC, H50S.441.28.HC, H50S.441.28C.HC, H50S.441.50.HC,
H50S.441.50C.HC, H50S.531.27.HC, H50S.531.27C.HC, H50S.531.50.HC,
H50S.531.50C.HC, H50S.541.27.HC, H50S.541.27C. HC, H50S.541.50.HC,
H50S.541.50C.HC, H50S.331.110C.HC, H50S.331.25C.HC, H50S.331.60C.HC,
H50S.341.110C.HC, H50S.341.25C.HC, H50S.341.60C.HC, H50S.311.110.SD,
H50S.311.15.SD, H50S.311.25. SD, H50S.311.60.SD, H50S.531.27.HCA,
H50S.531.50.HCA, H50S.541.27.HCA, H50S.541.50.HCA, H50S.531.27C.HCA,
H50S.531.50C.HCA, H50S.541.27C.HCA and H50S.541.50C.HCA are in conformity with
the requirements of the directives declared on this page.
CE
SIMPLIFIED EU DECLARATION OF CONFORMITY:
Hereby, iLOQ Oy declares that the radio equipment type H50S Padlocks are in
compliance with Directive 2014/53/EU. The full text of the EU declaration of
conformity is available at the following internet address:
https://www.iloq.com/en/company/patents-and-approvals/
Communication standard: NFC 13,56 MHz Load modulation (ASK) ISO/IEC 14443A, no
transmitter.
FCC
Chapter 1, Subpart A, Part 2 of Title 47 of the Code of Federal Regulations
The conformity was assessed in accordance the following standard:
FCC – FCC Rule Part 15
Note: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
ISED
Innovation, Science and Economic Development Canada (ISED)
The conformity was assessed in accordance the following standard: ISED – ICES
003, Issue 7: 2020 – class B
UKCA
Hereby, iLOQ Oy declares that the radio equipment type H50S Padlocks are in
compliance with the UK relevant statutory requirements. The full text of the
declaration of conformity is available at the following internet address:
https://www.iloq.com/en/company/patents-and-approvals/
H50S Padlock User Guide
iLOQ S5 / S50
H50S.x31.HC
H50S.x41.HC
iLOQ
www.support.iloq.com
Elektroniikkatie 10
90590 Oulu
Finland
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>